KOAKUMA X6 Three Axis Linkage Wireless Charger Car Holder User Manual
- June 9, 2024
- KOAKUMA
Table of Contents
Three-Axis Linkage
Wireless Charger Car
Holder
User Manual
Product introduction
1 Left arm clamp
2 Right arm clamp
3 Bottom bracket
4 indicator lights| 5 Wireless charging coil area
6 Button
7 Type-C charging port
8 Nut
---|---
Product parameters
Product name: X6
Operating frequency: 110K-205KHZ
Recommend Charging distance: ≤ 4mm
Input: 5V/2A, 9V/2A
Output power: 5W/7.5W/10W/15W
Applicable mobile phone: 4.0-6.9 inches
Product size: 98.56321.34 mm
Net weight: 135.2 g
Lighting mode
Mode | Indicator light |
---|---|
Power on | Indicator light is always on |
Standby | Indicator light is always on |
Charging | Indicator light breathing |
Full Charged | Indicator light breathing |
Foreign object detected | Indicator lights flash for 5s and turn off |
Over temperature protection status | Indicator light off |
Instructions for use
-
The product and the accessories are assembled and tightened by the ball head nut (compatible with other ball head diameter 17mm) ,and fixed in the suitable position of the car. Connect the product with QC3.0 car charger or ≥PD18W car charger (optional) by cable, and insert it into cigarette lighter .
-
After power on, the indicator light is always on, and it can automatically detect whether there is a mobile phone on the product:
1 When there’s a phone on it, the clamping arms hold the phone in a constant state.
2 Without a phone on it, the product will automatically open its arms and bottom bracket within 5 seconds to wait for the phone to be put upon it. When the mobile phone is placed on the product, the bottom support holds the mobile phone, the wireless charging coil will sense the metal parts of the mobile phone through the FOD, depending on the size of the phone, the bottom holder and the clamp-arms move simultaneously to the center of the coil, to automatically clamp the phone and charge it (if the phone has a wireless charging function) , because the ratio of length to width of the phone is basically the same, so the positions of the charging coil and the receiving coil are automatically aligned relative to each other. The charging efficiency can be ensured without adjusting the base support manually.
(The dual-coil version supports charging Samsung Z-FILP phones) -
If the phone does not support wireless charging, the indicator will flash and turn off for 5s (there may be part of the mobile phone without wireless charging function can not be detected by this product, the need to press the button to clamp the mobile phone.
-
In order to ensure the efficiency and stability of charging, the best wireless charging distance is ≤4mm and can not penetrate the metal, so need to avoid using metal or too thick mobile phone case, this allows the phone to charge quickly and wirelessly . (Charging distance ≥4mm is inefficient and ≥6mm may not charge)
-
The Way to remove the phone:
Click any button on the left or right, clamp-arms and bottom bracket are open to the maximum, waiting to take out the phone, if the phone is not taken out within 5 seconds, the product will automatically clamp the phone again. -
If the product does not turn on the light or flicker, button and wireless charging does not work, clamp-arms do not open or close, please stop using and return to the seller for Solving the problem.
Product description
- Wireless charging for devices that meet Qi wireless charging standards.
- Wireless charger supports 15W fast charging, Universal Apple and Android models.
- Wireless charging detective: when the mobile phone with wireless charging function close to machine and be sensed, it will open the left and right arm to automatically clamp the mobile phone, and start wireless charging.
- Foreign object detective: when a phone without wireless charging function is close to the machine and be sensed, the machine opens the clamp-arms and also automatically clamp the phone, it is used as a normal phone stand without charging.
- Fixed in the car air outlet, 360°adjustable, you can adjust the direction of your phone at will.
- Circuit protection function: over-current protection, overheat protection, short circuit protection
- Certification:FCC,CE,ROHS
Suction cup holder
Position the sucker in the right position (dashboard and windshield), adjust
the angle, press the locking-key to make the sucker lock firmly.
After fixing, the angle and distance can be adjusted at will. (TPU sucker +
drop glue double adsorption, one-key to lock.)
Air vent mount
Adjust the position of the support part and the Rotatory vent-mount according to the position of car outlets, install the machine to the car outlet, select the locking switch gear according to the thickness of the blades; Suitable for most automobile air outlet. The silicon rubber of the clamp mouth contacts the air outlet, more tightly fits, better protects the outlet not to be scratched.
Product details
- This product has a built-in capacitor, after power off within 5 minutes can still open the clamp arm twice, to prevent it can not open the clamp-arms after the car stalled.
- This product uses the clamp-arms and the bottom support_three-axis linkage automatic clamp design.
- The anti-slip silicone pad is designed with Partial slit design, which will not block the keys of the mobile phone.
- This product has a circular cooling hole, to protect mobile phone charging does not heat.
Packing list
- Car wireless charger *1
- USB cable *1
- Suction cup holder*1
- Air outlet clip *1
- User Manual *1
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
Warning: changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm
between the radiator and your body.