APPAREO AT-130 Cellular Asset Tracker Installation Guide
- June 6, 2024
- APPAREO
Table of Contents
AT-130
INSTALLATION MANUAL
Document revision: 0.4
Last revised: February 5, 2021
© 2020-21 Appareo Systems, LLC. All Rights Reserved.
AT-130 Installation Manual. All content within is copyrighted by Appareo
Systems, LLC, and may not be reprinted without permission.
The content of this manual is furnished for informational use only, is subject
to change without notice, and should not be construed as a commitment by
Appareo Systems. Appareo Systems assumes no responsibility or liability for
any errors or inaccuracies that may appear in the content contained in this
guide.
AT-130, Appareo, Appareo Systems, and the Appareo logo are trademarks or
registered trademarks of Appareo Systems. All other trademarks are property of
their respective owner. Appareo Systems, 1810 NDSU Research Circle North,
Fargo, ND 58102 USA.
Visit us online at www.appareo.com
Questions? E-mail us at [email protected]
Record of Revision
Revision Number| Change Description| Revision Date| Inserted
By
---|---|---|---
0.1| Prototype release| 11/11/20| AAL
0.2| Added regulatory verbiage| 12/4/20| AAL
0.3| Added regulatory verbiage, changed maximum torque.| 1/11/21| AAL
0.4| Added regulatory verbiage.| 2/5/21| AAL
Compliance
-
This device complies with part 15 of the FCC Rules and applicable RSS standards. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
-
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help. -
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
-
In order to comply with FCC and ISED RF Exposure requirements, this device must be installed such that a minimum separation distance of 20 cm is maintained between it and all persons during normal operation.
-
Afin de se conformer aux exigences d’exposition aux RF de la d’ISDE, cet appareil doit être installé de telle sorte qu’une distance de séparation minimale de 20 cm soit maintenue. entre lui et toutes les personnes pendant le fonctionnement normal.
-
FCC ID: 2AETC-AT130
About AT-130
The Appareo Asset Tracker, model AT-130 is a cost-effective, cellular, IP69K- rated asset tracking device with ultra-long battery life and industrial operating temperature range (-40 ℃ to +85 ℃).
Activating AT-130
In order to use AT-130, you need to activate it.
- Peel off the clear label on the back of the unit shown below. Flip over the unit to remove the magnet.
- Put the magnet in the Device Activation slot for five seconds. Check your asset tracking software to confirm that the device is activated (it should appear within 5-10 minutes if the unit is outside with the logo facing up).
Once the device is activated, discard the magnet or return it to the initial holding slot.
Installing AT-130
Installation Location
Choose an installation location that meets the following specifications:
- Mounted on a clean, flat surface.
- Mounted as high up as possible.
- The top (recommended) or top side of the unit has a clear view of the sky (not underneath or blocked by a metal surface).
- The device shall be installed so on the equipment so that the operator is, at minimum, 20 cm away from all external surfaces of the device.
Installing AT-130
Use 1/4″ or M5 bolts, washers, and nuts to mount AT-130 to its mounting
location. Torque to a maximum of 15 ft-lbs.
The spacing between bolts is 114mm, as shown below.
600840-000064, rev 0.4
Documents / Resources
|
APPAREO AT-130 Cellular Asset
Tracker
[pdf] Installation Guide
AT130, 2AETC-AT130, 2AETCAT130, AT-130 Cellular Asset Tracker, Cellular Asset
Tracker, Asset Tracker, Tracker
---|---