APPAREO 608065-000034 Gateway Installation Guide

APPAREO 608065-000034 Gateway

Specifications

• Name: Gateway 100, Gateway 260, Gateway 270, Gateway 360, Gateway 370
• Models: 240433, 608065-000034, 608065-000043, 608065-000034, 608065-000040
• Features:
  • Cellular
  • Wi-Fi
  • GPS
  • 433 MHz Radio
  • Satcom CAN Module
  • RS232 Broad R Reach

Product Usage Instructions

System Overview
Gateways are embedded computers that provide interfacing capability among a variety of wired and wireless networks. Refer to the table above for the specifications of each gateway.

General Information

Special Tools Required
No special tools are required for the installation of the gateway.

Hardware Components Background

Electrical Characteristics

• Product Rating: DC 12.0V/1A

Weight and Balance Information
The total weight of the gateway and antennas is listed below:

Equipment Dimensions
The dimensions of the equipment are as follows:

Conditions for Operation

IMPORTANT NOTICE:
This device can be configured to transmit on the 433 MHz frequency following the requirements of FCC Part 15.231(a-d). It must be used as a control signal, and failure to adhere to this requirement voids the authority to operate the equipment.

FAQ (Frequently Asked Questions)

• Q: Are special tools required for installing the gateway?
  A: No, special tools are not required for installation.

• Q: What is the electrical rating of the product?
  A: The product has a DC rating of 12.0V/1A.

• Q: What happens if the device is not configured to transmit on the 433 MHz frequency as a control signal?
  A: Failure to adhere to this requirement voids the authority to operate the equipment.

600840-000045
Gateway Installation Manual

Models: 608065-000034, 608065-000040, 608065-000043, 240433

This document and the information contained herein are the property of Appareo Systems, LLC and are confidential. They may not be disseminated or redistributed without the written permission of Appareo Systems, LLC| APPAREO SYSTEMS, LLC

FARGO, NORTH DAKOTA 58102

---|---
Gateway Installation Manual
DOCUMENT NUMBER

600840-000045

| Document Type

Manual

| Last Revised

June 28, 2023

| Rev

2.3

| Sheet

1 of 12

Record of Revisions

Revision Number| Change Description| Effective Date| Inserted By
---|---|---|---
1.0| Initial draft| 12/4/18| Lee Hinsz
1.1| Addition of model 608065-000040| 4/2/20| Lee Hinsz
1.2| Added ANATEL notification| 7/27/21| AAL
1.3| Added model 608065-000043| 8/19/21| GJG
2.0| General clean up, added Gateway 100, added additional cert approvals| 9/29/22| AAL
2.1| Added NCC warning statement and RATEL approval| 1/04/23| AAL
2.2| Updated System Overview table, Parts List notes| 5/16/23| AAL
2.3| Added Korean Class A Notice| 6/28/23| AAL

SYSTEM OVERVIEW

Gateways are embedded computers that provide interfacing capability among a variety of wired and wireless networks. Refer to the table below for the specifications of each gateway.

Name| Model| Cellular| Wi-Fi| GPS| 433

MHz Radio

| Satcom Module| CAN| RS232| Broad R Reach
---|---|---|---|---|---|---|---|---|---
Gateway 100| 240433| | x| x| | | x| x|
Gateway 260| 608065-

000034

(Middle Specification)

| x| x| x| | | x| x| x
Gateway 270| 608065-

000043

(Middle Specification)

| x| x| x| | | x| x| x
Gateway 360| 608065-

000034 (High

Specification)

| x| x| x| x| x| x| x| x
Gateway 370| 608065-

000040 (High

Specification)

| x| x| x| x| x| x| x| x

GENERAL INFORMATION

SPECIAL TOOLS REQUIRED

• SAE standard and/or metric wrenches, sockets, and screw drivers
• Torque wrench (in-lbs)

HARDWARE COMPONENTS BACKGROUND

Electrical Characteristics

• Product Rating : DC 12.0V/ 1A

Weight and Balance Information
The total weight of the gateway and antennas is listed below.

Table 1 Weight and Balance Information

Equipment Dimensions
Equipment dimensions are outlined in the table below for all required components in gateway installations. All figures given are representative of maximum equipment dimensions (where applicable).

Iridium – GNSS – 4G Cell Antenna

(HIRD-S2-0146A-01)

| 124.3| 80.3| 80.3

Conditions for operation

IMPORTANT NOTICE!!!!
This device can be configured to transmit on the 433 MHz frequency following the requirements of FCC Part 15.231(a-d). This requirement is that the transmission must be used as a control signal. It can include data transmission as well, or not, but in all cases it must be a control signal. Failure to adhere to this requirement voids the authority to operate the equipment.

INSTALLATION

With equipment installed, final configuration must meet the minimum separation distance in Table 5 and Section 3.2.

PARTS LIST FOR INSTALLATION
The following parts are required for the installation of a gateway.

Table 3 Parts List for Installation

Parts List for Installation

Item| Nomenclature| Part Number| QTY
1| Gateway*| 153510-000124 (MS)| 1
153510-000125 (MS)
153510-000126 (HS)
153510-000127 (HS)
153510-000159 (MS)
153510-000160 (HS)
153510-000162
2| 4G Cell – 433 MHz – WLAN

Antenna

| 252005-0000010 (HCEL-S2-0164A-00_Rev0 4G CELL-433MHz- WLAN)| 1
3| Iridium – GNSS

– 4G Cell Antenna

| 252005-000009 (HIRD-S2-0146A-0_RevA Iridium-GNSS-4G)| 1

*Only select one gateway part number to be utilized for installation.

• (MS) = Middle Specification gateways only contain cellular, WIFI, and GPS modules. Please terminate unused antennas.
• (HS) = High Specification gateways contain cellular, WIFI, GPS, Satellite Communications, 433 Radio Modules.

INSTALLATION INSTRUCTIONS

Install the gateway and antennas using the following steps:

1. Find an installation location for the gateway that meets these specifications: REQUIRED:

   • Meets the spacing requirements in Table 4.

   • Connectors point downward or sideways/horizontal (not up).

   • Avoid areas of moving parts or debris. For example, don’t mount it on the bottom of a frame that may be covered in mud or brush against crop/brush underneath.

   • Avoid high temperature areas such as engine bays, near exhaust systems, or on hydraulic manifolds.

   • Supports the preferred antenna locations in Step 2 (due to antenna cable length).
     RECOMMENDED:

   • Connectors pointing downward.

   • Do not mount directly next to other RF antennas (such as cell, radio, or Wi-Fi).

   • Mount within line of sight of the operator to observe LED.

2. Find an installation location for the antennas that meet these specifications:
   REQUIRED:

   • Meets the spacing requirements in Table 4.

   • Fins of the antennas are facing upward. The steel plate the antennas are mounted to should be flat and be towards the bottom of the installation. Do not mount sideways or upside down.

   • Antennas have line of sight to connected devices and sky.

   • Avoid mounting directly next to steel plates, tanks, or other structures. For example, avoid mounting the antenna on the side wall of an air cart, spreader, or sprayer tank.

   • Avoid mounting directly next to other RF antennas.

   • Do not mount inside the cab.

   • Do not run antenna cables alongside other electrical harnessing, especially high power circuits.
     RECOMMENDED:

   • Mount GPS antenna as central on the machine as possible.

3. Mount the gateway enclosure to the cab with ¼” or 6-mm fasteners and a torque of 30 in-lbs.

4. Torque the antenna terminations to gateway RF SMA connectors with a torque spec of 8.5 +/- 2 in-lbs.

The gateway and antennas must follow the distances in the following table and illustration to comply with FCC part 1.310 and ISED RSS-102.

Table 4 Separation Distance

4G Cell – 433 MHz – WLAN
Antenna
(Recommended minimum spacing between antennas is 7.5 cm)| 30 cm (in USA)
40 cm (in Canada and Europe)| 20 cm
**Iridium – GNSS – 4G Cell Antenna**| 30 cm (USA)

40 cm (in Canada and Europe)

| ** 20 cm
Gateway**| 20 cm| N/A

NOTE: Ensure the 4G Cell – 433 MHz – WLAN antenna has a metallic ground place of 300 x 300 mm for the mounting.

Torque the antenna mounting nut (M14x1) to 30 +/- 0.5 in-lbs.

REGULATORY INFORMATION

FEDERAL COMMUNICATIONS COMMISSION NOTIFICATION TO USER

Models: 608065-000034, 608065-000040, 608065-000043, 240433

These devices comply with Part 15 of the Federal Communications Commission (FCC) Rules. Operation is subject to the following two conditions:

1. These devices may not cause harmful interference, and
2. these devices must accept any interference received, including interference that may cause undesired operation.

These devices must be operated as supplied by Appareo Systems LLC. Any changes or modifications made to these devices without the express written approval of Appareo Systems LLC may void the user’s authority to operate these devices.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

INDUSTRY CANADA NOTIFICATIONS TO USER
Models : 608065-000034, 608065-000040, 608065-000043, 240433

These devices comply with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

ANATEL NOTIFICATION TO USER
This equipment is not protected against harmful interference and may not cause interference with duly authorized systems.

For more information, see the ANATEL website www.anatel.gov.br.

SOUTH AFRICA TYPE APPROVAL

UZBEKISTAN APPROVAL
This device has IEC Class 3 protection.

ARGENTINA APPROVAL

NCC WARNING STATEMENT

RATEL APPROVAL

KOREAN CLASS A NOTICE
600840-000045, rev. 2.3

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>