VENTURE LED Bluetooth Sensor Kit User Manual

: June 6, 2024
: VENTURE

Table of Contents

LED Bluetooth Sensor Kit
IMPORTANT SAFETY INFORMATION
Wiring Diagram
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LED Bluetooth Sensor Kit

VENTURE LIGHTING’S LED BLUETOOTH SENSOR KIT

USER MANUAL

Before You Begin
Read These Instructions Completely and Carefully

WARNING – RISK OF FIRE, ELECTRIC SHOCK, INJURY, OR PROPERTY DAMAGE

Failure to follow these instructions or altering equipment could result in injury or damage and void warranty. Venture assumes no liability for injury, damages, or losses of any kind that may arise from the improper, careless, or negligent installation, handling, or use of this product.
This equipment must be installed and serviced per applicable codes and ordinances by qualified personnel (ex. licensed electrician) familiar with the operation of the product and any hazards involved.
Disconnect power to the equipment and allow it to cool before installing or servicing.
Handle sharp edges with care. To prevent wiring damage, do not expose wiring to sharp edges.
Verify that all electrical connections have been properly made and the fixture is grounded to avoid potential electrical shocks.
It is the responsibility of the installer to confirm the proper input voltage is used with this equipment.
Do not handle energized equipment when hands are wet when standing on wet surfaces, or in water.

IMPORTANT SAFETY INFORMATION

All wiring and connectors used with this equipment shall be rated at a minimum of 90°C (194°F).
Bluetooth Sensor rated to operate in temperatures from -30°C to 70°C.
Bluetooth range: 15m to 20m but is highly dependent on the surrounding environment.

Bluetooth PIR Sensor Installation Instructions (Without Drop-Down Arm)

STEP 1: Attach threaded side mount nipple to sensor enclosure using (2) provided screws.

VENTURE LED Bluetooth Sensor Kit - Bluetooth PIR
Sensor

STEP 2: Push sensor threaded nipple through 1/2″ knockout on the fixture.
STEP 3: Thread nut onto threaded nipple on inside of fixture to secure the sensor in place.
STEP 4: Twist on the Highbay lens to the sensor.
NOTE: Lowbay lens available as an accessory.
STEP 5: Mount power pack to fixture using (2) 5/8″ screws.
NOTE: DO NOT puncture wires or LED modules.
NOTE: Pilot holes may be required.
STEP 6: Make electrical connections according to the wiring diagram.

Wiring Diagram

NOTE: Fixture may contain only one driver.

Bluetooth PIR Sensor Installation Instructions (With Drop-Down Arm)

STEP 1: Attach threaded side mount nipple to sensor enclosure using (2) provided screws.

VENTURE LED Bluetooth Sensor Kit - Bluetooth PIR
Sensor

STEP 2: Attach side mount nipple to drop-down arm by pushing in place until it clicks. There are 2 tabs that need to line up for it to click into place.
STEP 3: Open the drop-down arm so it is in 2 halves.
STEP 4: Push sensor threaded nipple through 1/2″ knockout on the drop- down arm.
STEP 5: Thread nut onto threaded nipple on inside of drop-down arm to secure the sensor in place.
STEP 6: Feed wires through arm and side mount nipple on the drop-down arm.

VENTURE LED Bluetooth Sensor Kit - wire

STEP 7: Snap 2 halves of the drop-down arm together.
STEP 8: Push drop-down arm threaded nipple through 1/2″ knockout on the fixture.
STEP 9: Thread nut onto threaded nipple on inside of fixture to secure the sensor in place.
STEP 10: Twist on the Highbay lens to the sensor.
NOTE: Lowbay lens available as an accessory.
STEP 11: Mount power pack to fixture using (2) screws.
NOTE: Be sure not to puncture wires or LED modules.
NOTE: Pilot holes may be required.
STEP 12: Make electrical connections according to the wiring diagram (above).