HELLA GUTMANN QSMM56V6500ML0222S0 Mega Macs 56 Diagnostic Device User Guide

HELLA GUTMANN QSMM56V6500ML0222S0 Mega Macs 56 Diagnostic Device User

Guide

1. About this Quick Start Guide

Translation of Original Operating Instructions
The quick start guide comprises the most important information in a clearly visible form to facilitate the start with the mega macs 56.

1.1 Notes for the Use of the Quick Start Guide
This quick start guide contains important information relevant to operator safety.

Go to www.hella-gutmann.com/manuals to find all the manuals, instructions, references and lists about our diagnostic devices, tools and much more.

Please also visit our Hella Academy under www.hella-academy.com and expand your knowledge with various online tutorials and other training courses.

Please read the quick start guide entirely. Pay special attention to the first pages containing the safety instructions.
They are provided solely to assure your safety when working with the device.

You are recommended to read the individual work steps in the manual again while working with the device, in order to avoid danger to personnel and equipment or operating errors.

The device shall be operated exclusively by personnel qualified in vehicle engineering. Information and knowledge included in this training is not explained further in this quick start guide.

The manufacturer reserves the right to modify this quick start guide and the device itself without prior notice. We therefore recommend checking for any updates. This quick start guide must accompany the device in case of sale or other transfer.

The quick start guide must be kept for the entire service life of the device and accessible at any time.

1.2 Range of Functions
The range of functions of the software may vary depending on the country, the licenses acquired, and/or the optionally available hardware. This documentation may therefore describe functions that are not available on the individual device. Missing functions can be enabled by acquiring a corresponding license subject to charge and/or additional hardware.

2. Safety Precautions

2.1 Safety Precautions – Risk of Injury

2.2 Safety Precautions for the mega macs 56

2.3 Safety Precautions for Testing/Measuring Devices

3. Product Description

3.1 Delivery Contents

3.1.1 Checking Delivery Contents
Please check the delivery contents upon receiving your device so that complaints can be issued immediately regarding any potential damage.

Proceed as follows to check the delivery contents:

1. Open the package supplied and check for completeness based on the delivery slip.
Should you identify any damage to the package, then open the package in the presence of the delivery service and check the device for hidden damage. Any transport damage to the package supplied and damage to the device shall be registered in a damage report by the delivery service.

2. Take the device out of the packaging.

3. Check the device for mechanical damage and shake it slightly to ensure that there are no loose parts inside.

3.2 Intended Use

The mega macs 56 is a mobile device for detecting and rectifying faults in automotive electronic systems.

It uses a diagnostic interface to establish a connection to the automotive electronics and to provide access to descriptions of the vehicle system. A lot of this data is transferred to the device directly from the Hella Gutmann diagnostic database via online connection. Therefore, the device must be permanently online.

The device is not suitable for repairing electrical machines and equipment or home electrics. Diagnostic devices from other manufacturers will not be supported.

If the device is used in a way not authorized by Hella Gutmann, the safety of the device may be influenced.

The device is intended for industrial use. Outside of industrial environments, e.g., in commercial areas or in the centre of a town, radio interference suppression measures may need to be taken.

3.3 Using the Bluetooth® Function
The terms of use of the Bluetooth® function may be restricted or prohibited through law or corresponding legal regulations in certain countries.

Observe the provisions in force in the respective country before using the Bluetooth® function.

3.4 Operating the Device

NOTICE
Damage or destruction of the display
Never touch the display using a tool or pointed metal object.
Always use your finger.

The device is equipped with a touch screen display. All menus and functions can be selected and or activated by slightly touching with the finger or just by pressing the arrow keys ▼ ▲.

3.5 Connections of the mega macs 56

3.6 DT VCI Connections

3.6.1 Meaning of the Flashing Frequencies

4. Installation of the Hella Gutmann Drivers Package

4.1 System Requirements of Hella Gutmann Drivers

• Windows 7 SP1 or higher
• Windows administrator rights

4.2 Installation of the Hella Gutmann Drivers Package
To obtain all the data about the related vehicle provided by Hella Gutmann, the device requires a permanent online connection and the installed driver package Hella Gutmann Drivers. To keep the connection costs down, Hella Gutmann recommends a DSL connection and a flat rate.

1. Install the Hella Gutmann Drivers on the office or repair shop PC.
   The driver package Hella Gutmann Drivers program is on the supplied HGS data carrier.

2. Connect the device to a web-compatible PC.

Once the connection symbol in the top symbol bar changes from black to green, the online connection has been set up successfully and is active.

5. Initial Start-Up

This section gives a description of how to switch the device on and off as well as all the necessary steps for the first use of the device.

5.1 Charging the Battery
Prior to putting the device into operation, charge the battery for at least 8 to 10 h while the device is switched off.

Proceed as follows to charge the battery:

1. Insert the voltage supply plug into the device’s socket.
2. Insert the power plug into the plug socket.

The battery is being charged.

5.2 Switching On the Device

NOTE

• When starting the device for the first time and after every software update, you need to
  confirm the general terms and conditions (GTC) of the Hella Gutmann Solutions GmbH.
  Otherwise, certain device functions will be unavailable.

• The first time the device is started you need to confirm also the order processing agreement
  of the Hella Gutmann Solutions GmbH. It governs the handling of personal data pursuant to the GDPR.

• If mega macs 56 recovery (“Rescue App”) is displayed when switching on the device, contact the responsible support staff or the Hella Gutmann Technical Help Line.

To switch on the tool:

Now you can start working with the device.

5.3 License Release

NOTE
In order to use the full scope of the purchased licenses you need to connect the device to the HGS server prior to the first start-up.

Proceed as follows to connect the device with the HGS server:

Now you can start working with the device.

5.4 Switching off the Device

Proceed as follows to switch off the device:

6. Configuring the Device

Configure all interfaces and functions under>Settings< in the main menu.

6.1 Configuring the Interfaces
Here you can configure the interfaces for the printer, BPC-Tool, Bluetooth® and WLAN.
Configure all interfaces of the device under Settings > Interfaces.

If there are several possible connections to devices or tools, the fastest and most stable connection is always preferred.

The hierarchy for connection is as follows:

1. USB
2. Bluetooth®
3. WLAN

6.1.1 Configuring the Bluetooth® Adapter
Configure the Bluetooth® adapter here.

The integrated Bluetooth® module enables a wireless connection to a PC on which the driver package Hella Gutmann Drivers is installed.

6.1.1.1 Searching for Bluetooth® Adapter

NOTE
If the device has already been delivered with a Bluetooth® adapter, both devices are already
assigned to each other ex works.

Proceed as follows to search for the Bluetooth® adapter:

The automatically assigned Bluetooth® adapter address appears in the field Bluetooth® adapter address.

7. Working with the Device

7.1 Symbols

7.1.1 General Symbols

7.1.2 Symbols in the Main Menu

7.1.3 Symbols in the Vehicle Selection Menu

7.1.4 Symbols in the Vehicle information menu

7.2 Diagnostics

7.2.1 Preparing Vehicle Diagnostics
The selection of the correct vehicle is a basic precondition for trouble-free vehicle diagnostics. The device provides assistance to simplify the selection, e.g., indicating the installation position of the diagnostic connector or vehicle identification by VIN.

The following ECU functions are possible in the >Diagnostics< menu:

• Trouble code readout
• Parameter readout
• Actuator tests
• Service reset
• Basic settings
• Codings
• Test function

Proceed as follows to prepare vehicle diagnostics:

1. Select the desired vehicle under >Vehicle selection< in the main menu.
2. Select >Diagnostics< in the main menu.

3. Insert the DT VCI into the vehicle’s diagnostic connector.
Both LEDs of the DT VCI flash. The DT VCI is ready for operation.

Now you can select the type of diagnostics.

7.2.2 Performing Diagnostics
Proceed as follows to perform diagnostics:

1. Select the desired vehicle under >Vehicle selection< in the main menu.
2. Select >Diagnostics< in the main menu.

7.3 Calling Up Vehicle Information
Here you have an overview of the following vehicle information:

• Car History
• Component help
• Service data

NOTE
You require an online connection if you wish to access all available information.

Proceed as follows to call up vehicle information:

1. Select >Vehicle information< in the main menu.
2. Select the requested type of information using the symbols.

Certain types of information may not be available depending on the selected vehicle.

8. Measurements

NOTE
The use of the measuring technology menu requires the optionally available measurement module (MT 56).

Here you can select measured variables and channel. Then you can perform various measurements.

Measurement technology is a digital signal acquisition and output. This means that the voltage signal is detected and saved within a few microseconds. Only if there are enough values saved, the signal will be displayed as a curve on the screen.

8.1 Oscilloscope
The use of the measuring technology menu requires the optionally available measurement module (MT 56).

Use the oscilloscope for measuring and/or depicting the following measured variables:

• Voltage
• Current
• Resistance

Current measurements are allowed exclusively with the clamp meter from Hella Gutmann. Depending on the required measurement, different clamps are to be used.

CAUTION
Overvoltage
Fire hazard/danger of damage to the device and its surroundings
Comply with the max. permitted voltage load of the oscilloscope channels

8.1.1 Performing Oscilloscope Measurements
Proceed as follows to perform oscilloscope measurements:

HELLA GUTMANN SOLUTIONS GMBH
Am Krebsbach 2
79241 Ihringen
GERMANY
Phone: +49 7668 9900–0
Fax: +49 7668 9900–3999
[email protected]
www.hella-gutmann.com
© 2022 HELLA GUTMANN SOLUTIONS GMBH

Read More About This Manual & Download PDF:

References

• gutmann.com
• Startseite | Trainingsportal
• Hella Gutmann Solutions GmbH: Hella Gutmann Solutions
• Hella Gutmann Solutions GmbH: Manuals

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>