CMSIS-DAP/DAPLink User Manual

• Introduction

• Feature

• MDK Config
  o [Debugger Select](https://github.com/wuxx/nanoDAP/blob/master/user_manual_en.md

  debugger-select)

  o Target Detect
  o [Flash Algorithm](https://github.com/wuxx/nanoDAP/blob/master/user_manual_en.md

  flash-algorithm)

  o Reset Setting

• DAPLink Usage
  o Drag-and- Drop
  o [Firmware Upgrade](https://github.com/wuxx/nanoDAP/blob/master/user_manual_en.md

  firmware-upgrade)

Introduction

CMSIS-DAP/DAPLink is a cmsis-dap debugger made by MuseLab which support SWD/JTAG and a USB CDC serial port.

Feature

• open source hardware/software
• 5V/3.3V power supply to target board
• SWD interface
• JTAG interface
• USB CDC serial port
• DAPLink is a upgrade of CMSIS-DAP, which support drag-n-drop program
• DAPLink support drag-n-drop upgrade the firmware

MDK config

plug the debugger into PC USB, if everything is ok, there will appear a CDC port and a USB HID device

Debugger Select

select CMSIS-DAP Debugger in Option -> Debug

Target Detect

click Settings in Option -> Debug, recommend to select the swd port, and config the frequence to 10MHz

Flash Algorithm

you need to config the flash algorithm for your target mcu, here is a example with stm32f1x Note: select the Reset and Run for target auto reset after program done.

Reset Setting

Generally, you may need to start the mcu when program done, config the Reset type to SYSRESETREQ here and select Reset and Run in the Flash Download Page above.

DAPLink Usage

Drag and Drop

plug the DAPLink into PC USB, there will be a USB DISK appear called DAPLink,

DAPLink support drag and drop program, just drag the binary with suffix hex or bin into the DAPLink, the DAPLink will do all the program work.
Tips: one firmware can only support one type of MCU drag-n-drop program, for different type of MCU, you may need to compile the source yourself.

Firmware Upgrade

DAPLink implement a bootloader with USB MSD, which made it very easy for the firmware upgrade.

1. short the nRST and GND.
2. plug the DAPLink into PC USB, a USB DISK named MAINTAINENCE will appear.
3. disconnect the nRST and GND.
4. drag the new firmware into the MAINTAINENCE, wait for a few moment, then upgrade done, a new USB DISK DAPLINK will appear with replace of MAINTAINENCE

References

• nanoDAP/doc/DAPLink_MSD.png at master · wuxx/nanoDAP · GitHub
• nanoDAP/doc/debug_select.jpg at master · wuxx/nanoDAP · GitHub
• nanoDAP/doc/flash_algorithm.jpg at master · wuxx/nanoDAP · GitHub
• nanoDAP/doc/nanoDAP2.jpg at master · wuxx/nanoDAP · GitHub
• nanoDAP/doc/reset_select.jpg at master · wuxx/nanoDAP · GitHub
• nanoDAP/doc/target_id1.png at master · wuxx/nanoDAP · GitHub
• nanoDAP/doc/usb_device.png at master · wuxx/nanoDAP · GitHub
• nanoDAP/user_manual_en.md at master · wuxx/nanoDAP · GitHub
• nanoDAP/user_manual_en.md at master · wuxx/nanoDAP · GitHub
• nanoDAP/user_manual_en.md at master · wuxx/nanoDAP · GitHub
• nanoDAP/user_manual_en.md at master · wuxx/nanoDAP · GitHub
• nanoDAP/user_manual_en.md at master · wuxx/nanoDAP · GitHub
• nanoDAP/user_manual_en.md at master · wuxx/nanoDAP · GitHub
• nanoDAP/user_manual_en.md at master · wuxx/nanoDAP · GitHub
• nanoDAP/user_manual_en.md at master · wuxx/nanoDAP · GitHub
• nanoDAP/user_manual_en.md at master · wuxx/nanoDAP · GitHub
• nanoDAP/user_manual_en.md at master · wuxx/nanoDAP · GitHub

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>