SILVERCREST Electric Stove Sek 2000 B2 Instructions

: June 6, 2024
: SILVERCREST

SILVERCREST® Electric Stove SEK 2000 B2 Instructions

Electric Stove SEK 2000 B2

ELECTRIC STOVE

Operation and Safety Instructions

This product is only suitable for well insulated spaces or occasional use.

Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the device.

Parts Guide

Introduction

Congratulations for purchasing your new device. You have selected a high- quality product. The instruction manual is an integral part of this product. It contains important information regarding safety, device handling and disposal. Familiarise yourself with all operating and safety instructions before using the product. Only use the product as described and for the areas of use specified. Please make sure to hand over all documents when handing the product over to third parties.

Intended use

This device is only intended for heating closed and dry rooms during transitional periods. The device is not intended for use in rooms exposed to potentially hazardous conditions, such as corrosive or explosive atmospheres (dust, vapour or gas). Do not use the device outdoors. Any other use or modification of the device is regarded as improper use and poses a considerable risk of accidents. We shall not assume liability for any damages resulting from improper use. The device is intended for private use only.

Scope of delivery

1 Electric stove
1 Instruction manual
4 Stands
12 Screws

Equipment

Electric stove
Operating panel
Thermostat
Screws M4 x 15 mm
Stands
Ventilation grille

Technical data

Voltage rating: 220-240 V~, 50 Hz
Power rating: 1750 W – 1950 W
Protection class: I
Environmental conditions: 0 °C to +35 °C
Device dimensions: approx. 38 x 23 x 51 cm
Heat output:
Heating level 1: 950 W
Heating level 2: 1950 W

Information requirements for electric local space heaters

Model identifier(s): SEK 2000 B2

ROWI Germany GmbH
Werner-von-Siemens-Str. 27
76694 Forst
GERMANY

Safety information

Please read all safety information and instructions.

Failure to comply with the safety instructions and precautions may result in serious injury and/or property damage.

For future reference, keep all safety instructions and precautions in a safe place!

General safety information

The device is only intended for indoor use!

Read this instruction manual carefully before using the device. They are an integral part of the device and must be available at all times.
Only use the device for the intended purposes described.
Please verify that the mains voltage required (see type plate on the device) corresponds to your mains voltage.
In the event of any malfunctions, the device may only be repaired by our authorised service centre.
The device may only be installed on a firm, level, dry and non-combustible surface.
Please ensure that the power socket is easily accessible to be able to quickly disconnect the power plug from the mains, if necessary

Electric shock protection

Danger to life by electrical current!

Contacting the live cables or components is dangerous to your life!

Only connect the device to a correctly installed grounded power socket.
If the device falls to the ground or sustains a severe impact, or if it falls into water, stop using it immediately. In such cases, please contact our service centre.
If the power supply cable of this device is damaged it should be replaced by the manufacturer or by its customer service or a similarly qualified person, to avoid danger.
Never use the device in the direct vicinity of a sink, bath tub, shower or swimming pool as water spray may enter the appliance.
Never allow water or other liquids to enter the device. Therefore:
- never use the device outdoors,
- never place containers filled with liquids, such as drinking glasses, vases, etc., on the device,
- never use in a very humid environment such as a bathroom. If any liquids do get into the device, unplug the power cord immediately and ensure the device is repaired by a qualified technician.
Never attempt to reach through the protective grilles into the interior of the device using your fingers or any other objects.
Never touch the device, the mains cable or the mains plug with wet hands.
Always unplug the mains cable by pulling the plug. Never pull on the cable itself.
Ensure the power cable does not kink or become trapped.
Take care to ensure that the power cord is not damaged by sharp edges.
Keep the mains cable away from hot surfaces (e.g. cookers/ stoves).
If you do not intend to use the appliance for an extended period of time, unplug the appliance from the wall socket. Only then is the device completely free of electrical current.
Extension cord use is prohibited.
Using an external timer or a separate remote control system, such as a radio socket with the device is prohibited.

Fire risk!
Since the device operates at high temperatures, observe the following safety instructions to prevent fire hazards.

Risk of overheating!
To avoid overheating of the device, never cover it with anything.

Do not place any flammable objects (e.g. curtains, paper, etc.) in the immediate vicinity of the device during operation.
Never use the device to dry textiles or other things on, above or in front of the device.
When setting up the device, observe a minimum clearance of 0.5 m from other devices or the wall.
Never operate the device in potentially explosive atmospheres or in the vicinity of flammable gases or liquids.
Never place the device directly under a wall-mounted power socket as the heat generated could damage its electrical components.
Always ensure that air can always enter and exit the device freely. Failure to do so may result in heat build-up in the device.
Never leave the device running unattended. Damage is almost always indicated by the formation of intense odours. If this occurs, unplug the power cord immediately and arrange for the device to be inspected.

Injury prevention

Observe the following instructions to prevent injuries.
Please take care to ensure that the mains power cable never becomes a tripping hazard or causes someone to get caught in it or step on it.
Maintain an adequate distance from the device so that hair or clothing is not sucked into the device by the fan.

Beware of hot surfaces!
Some parts of the product can become very hot and cause burns. Pay particular attention when children and vulnerable people are present.

Child safety

Children are usually unable to assess hazards correctly and are often vulnerable to personal injury. Please keep this in mind:
This device may only be used under adult supervision to ensure that children do not play with it.
Always ensure that the device is out of the reach of children.
Be careful to ensure that the packaging film does not become a lethal trap for children. Packaging film is not a toy.
This device can be used by children aged from 8 years and above and by physically, sensory or mentally restricted persons if they are supervised or given instructions on safe use and understand the hazards involved. This device is not a toy for children to play with! Cleaning and user maintenance shall not be carried out by children without supervision.
Children under the age of 3 are to be kept away from the device unless they are continually supervised.
Children between the age of 3 and 8 are only allowed to switch the device on or off if they are supervised or given instructions on safe use and understand the hazards involved, provided that it has been placed or installed in its intended normal operating position.
Children between the ages of 3 and 8 shall not plug in, regulate, clean the heater or perform user maintenance.

Installation preparation

Remove all packaging materials and all transport bracing from the device.
Check the delivery contents for completeness and any signs of damage.

Stand installation

After you have completely unpacked the device, place it upside down on a clean surface so that you can fully see the underside (Fig. 1).
Take a stand 5 and insert 3 screws 4 through the holes (Fig. 2).
There are 3 matching holes in each corner of the device. Now take the stand 5 with the screws 4 uand place it exactly over the matching holes.
When the screws 4 are inserted in the correct holes, tighten them with a screwdriver (Fig. 3).
Please proceed in the same way with all four stands 5 until they have all been assembled.
The device can now be placed on its stands 5 . The device is ready for start-up (Fig. 4).

Starting-up

Please find a suitable location for the device before starting it up.

For safe and trouble-free running of the device, choose an installation location which meets the following requirements:

```
* The floor should be firm, flat and horizontal.
```
- The device should be set up at least one metre away from furniture, curtains and other easily flammable objects.
- Do not place the device in a hot, wet or very humid environment.
- A grounded socket protected by a residual-current device with overload protection should be available in the vicinity of the device.
- The power socket should be easily accessible so that the mains connection cable can be easily disconnected, if necessary.
- Extension cords are prohibited.
Plug the device cable into the grounded power socket.

IMPORTANT! The cable must remain on the rear-side of the device and must not come into contact with any hot elements.

Device operation

The device is operated via the operation panel 2 and the thermostat 3 on the right-hand side (Fig. 5).
The first switch with the [ ] symbol switches the flame effect on and off. The flame effect can be used with or without the heating function. If the switch is set to the [ O ] symbol, the flame effect is switched off. If you press the switch to the left [‒], you will activate the device.
For a low amount of heating, switch the first heating level with the [ I ] symbol to the [‒] symbol to turn it on and to the [ O ] symbol to turn it off. The heating function can be used with or without the flame effect.
For full heating power, switch on both heating levels [ I ] and [ II ] using the on/off switches.
Heating level [ II ] only functions if the switch for heating level [ I ] is also set to the [‒] symbol. The temperature of the two heating stages can be controlled using the thermostat 3 by setting it between the [‒] and [+] settings. Turning the thermostat 3 clockwise until you hear an audible click will switch on the device. [‒] represents the lowest temperature (left) and [+] (right) the highest temperature.

PLEASE NOTE! Thanks to automatic operation, the hot-air control (thermostat) maintains the preprogrammed temperature at a constant level.

First, turn the thermostat 3 to the right in the direction of the maximum value. Leave the switch in this position until the air in the room has reached your desired temperature.

PLEASE NOTE! When you use the device for the first time, a slight odour may occur.

Overheat protection

For your safety, this device features overheating protection. If the temperature inside the device becomes too high, it will switch off automatically. In this case, proceed as follows:

Disconnect the power plug from the mains.
Wait until the device has cooled down for at least 20 minutes.
Ensure that the ventilation grilles 6 are not obstructed and clean them with a soft, dry cloth.
Restart the device. After you have done this, you can continue to use the device as normal. If the fault occurs repeatedly and no apparent fault can be found, arrange for the unit to be repaired or stop using it immediately.

Maintenance and cleaning

CAUTION! RISK OF ELECTRIC SHOCK!
Before cleaning, always unplug the device from the mains and allow it to cool down completely.
Clean the outside of the device with a soft, dry cloth. Do not use liquids under any circumstances, especially ones containing petrol, or cleaning agents, as these will damage the device.
Remove dust and dirt from the ventilation grilles 6 regularly using a vacuum cleaner.

Disposal

The device packaging is made of environmentally friendly materials that you can dispose of at your local recycling centres.

The product and packaging materials are recyclable, dispose of it separately for better waste treatment. The Triman logo is valid in France only.

Please note the labelling of the packaging materials during waste separation, these are marked with abbreviations and numbers which indicate the following: 1–7: Plastics/20-22: Paper and cardboard/80-98: Composite materials.

Do not dispose of the product with your regular household waste. Bring it to a municipal collection point for recycling! For information on how to dispose of the old device, contact your local authority or city council.

Service

If any problems occur during use of your ROWI Germany product, please proceed as follows:

Contact us
You can contact the service team of ROWI Germany at:

ROWI Germany GmbH
Werner-von-Siemens-Str. 27
76694 Forst
GERMANY
lidl-services@rowi-group.com
Service-Hotline: +800 7694 7694
(free call from a German landline)

IAN 365183_2101

Most problems can be resolved with the skilled technical support of our Service Team.