BE Ratchet Locking Jack Stands Instruction Manual

: October 27, 2023
: BE

Table of Contents

BE Ratchet Locking Jack Stands
OPERATING INSTRUCTIONS MANUAL
INSPECTION
ASSEMBLY
OPERATION
MAINTENANCE
WARRANTY INFORMATION
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BE Ratchet Locking Jack Stands

BE-Ratchet-Locking-Jack-Stands-PRODUCT-IMG

OPERATING INSTRUCTIONS MANUAL

MODEL NO.| CAPACITY| BASE SIZE| MIN. HEIGHT| MAX. HEIGHT
---|---|---|---|---
35.200.002| 2 Ton| 7.59” x 6.88”| 11-1/8”| 16-15/16”
35.200.003| 3 Ton| 8.15” x 7.4”| 11-13/16”| 17-7/16”
35.200.006| 6 Ton| 11.22” x 9.84”| 15-3/4”| 24-3/8”
35.200.012| 12 Ton| 11.81” x 10.63”| 17-11/16”| 27-1/2”

SAFETY & WARNING INFORMATION

This is the safety notification symbol. This symbol will notify you of any potential injury hazards. Please follow all instructions that follow this symbol to avoid possible injuries or death
Indicates a hazardous situation. If proper stepsare not followed, death or serious injury could result

IMPORTANT: READ ALL INSTRUCTIONS BEFORE USE

Before using these jack stands, be sure to read all content within this manual, ensuring that you understand the operating procedures, maintenance requirements and all safety warnings. The owner and/or operator shall have an understanding of the product, its operating characteristics, and safety operating instructions before operating this device. Safety information shall be emphasized and understood. If the operator is not fluent in English, the product and safety instructions shall be read to and discussed with the operator in the operator’s native language by the purchaser/owner or his designee, making sure that the operator comprehends their contents. These jack stands meet or exceed ASME/PASE 2014 standards

ACTIONS TO HELP PREVENT DANGEROUS SITUATIONS

Study, understand and follow all instructions before operating this device.
Do not exceed the rated capacity stated.
Use only on hard, level surfaces.
Lift only on areas of the vehicle as speciﬁed by the vehicle manufacturer.
No alterations shall be made to this product.
Jack Stands are designed to support stated capacity. Stands should only be used to support partial loads that consist of one end of a vehicle. Always use as a matched pair to support one end of a vehicle only.
Never use jack stands to support both ends or one side of a vehicle.
Use only one (1) pair of stands per vehicle.
Rated capacity is per pair only.
Failure to heed these warnings may result in serious personal injury and/or property damage.

INSPECTION

This device shall be inspected immediately if the device is believed to have been subjected to an abnormal load or shock. It is recommended that this inspection be made by a manufacturer’s or supplier’s authorized repair facility.
Owners and/or operators should be aware that repair of this equipment may require specialized knowledge and facilities. It is recommended that an annual inspection of the product be made by a manufacturer’s or supplier’s authorized repair facility and that any defective parts, decals, or safety labels or signs be replaced with manufacturer’s or supplier’s speciﬁed parts.

DAMAGED EQUIPMENT AND ADD-ONS
Any jack stand that appears to be damaged, is found to be worn or operates abnormally in any way will be removed from service and destroyed immediately.
Alterations
Because of potential hazards associated with this type of equipment, no alterations shall be made to the product.
Attachments and Adapters
Only attachments and/or adapters supplied by the manufacturer shall be used.

SETUP

Prior to each use, visual inspection (See Pg.2) shall be made to the device by checking for abnormal conditions, such as cracked welds, damaged, loose or missing parts.
Consult the vehicle owner’s manual to determine the location of support points.
Be sure to set the vehicle in park with the emergency brake on and wheels securely chocked.
Be sure that the vehicle and the jack stands are on a hard, level surface.

ASSEMBLY

Insert ratchet bar into collar.
Lift ratchet bar upward to ensure the ratchet and locking pawl positively engage at each and every position.
To lower, lift the handle, disengage the locking pawl from the ratchet bar and slowly move the ratchet bar down.
Use a hammer and punch to bend the locking tab inward (3 & 6 Ton). This will prevent the ratchet bar from accidentally coming loose.
For 12 Ton jack stands, tighten the provided hex bolt into the collar to prevent the loss of the ratchet bar (See bottom of page for details).

OPERATION

For correct stability choose a hard and ﬂat surface.
Engage the hand brake and put the vehicle into gear.
Adjust the ratchet bar to the desired height, and lock it with the locking handle.
Secure the jack stand with the safety pin.
Jack up your vehicle as speciﬁed by the manufacturer.
Centre the load over the saddle of the jack stand. It is advisable to leave the jack in place when the weight of the vehicle is supported by the jack stand.
To remove the jack stand, jack the vehicle up again, pull the jack stand free, then lower the vehicle to the ground.
Protect the jack stands from corrosion by cleaning them thoroughly. Do not apply oils or lubricants to any portion of this product

MAINTENANCE

Inspect each stand before use. Ensure all parts move freely. Only apply grease to the locking handle pivot point of this product and ensure all excess grease is wiped away before stand is used. If rust appears, sand away the rust area and cover with appropriate utility paint. Please note that there are no replacement parts available for this product.

WARRANTY INFORMATION

TWO YEARS LIMITED WARRANTY

For a period of two (2) years from your purchase date, BE AG & INDUSTRIAL will repair or replace (at its option) without charge, your BE AG & INDUSTRIAL product if it was purchased new and the product has failed due to a defect in material or workmanship which you experienced during normal use of the product. This limited warranty is your exclusive remedy.
If this BE AG & INDUSTRIAL product is altered, abused, misused, modiﬁed, or undergoes service by an unauthorized technician, your warranty will be void. We are not responsible for damage to ornamental designs you place on this BE AG & INDUSTRIAL product and such ornamentation should not cover any warnings or instructions or they may void the warranty. This warranty does not cover scratches, superﬁcial dents, and other abrasions to the paint ﬁnish that occur under normal use.
To access the beneﬁts of this warranty, contact the dealer or retailer where the unit was purchased. For further assistance, you can contact BE AG & INDUSTRIAL at warranty@brabereq.com for conﬁrmation that this warranty applies. Thereafter, you may be advised to return the product under warranty, freight prepaid, to the dealer or directly to the BE AG & INDUSTRIAL service department.
Subject to the law in your state:
(1) Your sole and exclusive remedy is repair or replacement of the defective product as described above.
(2) BE AG & INDUSTRIAL is not liable for any incidental damages, including but not limited to, lost proﬁts and unforeseeable consequences.
(3) The repair and replacement of this product under the express limited warranty described above is your exclusive remedy and is provided in lieu of all other warranties, express or implied. All other warranties, including implied warranties and warranties of merchantability or ﬁtness for a particular purpose are disclaimed and, if disclaimer is prohibited, these warranties are limited to two years from your date of purchase of this product.