Lyfco OH-008 Towel Dryer Instruction Manual
- October 30, 2023
- Lyfco
Table of Contents
Lyfco OH-008 Towel Dryer
Product Information
The product is a swivel heated towel rail that is designed to keep towels warm and dry. The power leg mount is included for the installation of the power cord. Please note that the product is provided by Konsumentkontakt Arc E-commerce AB and the contact details are Box 3124, 13603 Haninge Sverige.
Product Usage Instructions
Before installing the swivel heated towel rail, please ensure that you read and understand the user manual and follow the instructions carefully. Failure to do so may result in electric shock or other hazards.
- Start by locating a suitable location for the towel rail. Choose a location that is close to an electrical outlet and where the towel rail can be easily accessed.
- Once you have chosen a location, use the power leg mount to install the power cord. Make sure that the power cord is securely attached before proceeding.
- Next, attach the towel rail to the wall using the appropriate screws and brackets. Make sure that the towel rail is level and securely attached to the wall.
- Connect the power cord to the electrical outlet and switch on the power. The towel rail should start heating up immediately.
- Wait for a few minutes for the towel rail to heat up fully. Once it is heated up, you can hang your towels on it and they will start to dry and warm up.
Please note that if you experience any issues with the installation or usage of the swivel heated towel rail, please contact Konsumentkontakt Arc E-commerce AB for assistance.
PARTS LIST
PARTS / ASSEMBLY
Leg Mounts (leg for mounting the unit)
Wall Bushing (conduit for wall power)
MOUNT WARMER
INSTALL POWER LEG FLANGE
This only applies to the Power Leg Mount 1 for the Hard-Wired option (bottom-
right leg). The Wall Bushing 1 allows the Power Cord to be passed into the
wall cavity for hard-wiring to your home’s electrical wiring.
NOTE: Before proceeding, make sue you have a plan for directing the power
cord to an existing circuit. It may be necessary to use a fishing tool after
drilling the 1/2″ hole to pull the cord to a location for connecting to
power(see page 10 for ideas).
After ensuring there are no obstructions behind the wall, drill a 1/2-inch
hole through the drywall at the wall marking made earlier. Inset the Wall
Bushing 1 throught the Power Wall Flange D and screw the bushing into the hole
you drilled into the drywall. Screw the bushing until it’s snug and the small
holes in bushing are aligned vertically.
INSERT POWER CORD
While holding the warmer near the wall, inset the power cord through the Wall
Bushing 10 and pull the cord tight from within the wall cavity.(see the next
pages for ideas on connecting the power cord to power inside the wall).
NOTICE FOR HOW TO INSTALL THE SWIVEL HEATED TOWEL RAIL
Noted: In order to ensure the normal use of the internal components,
Please install the warmer according to the drawings operation after taking out
the product.
- Step 1: Taking out the product and place it in a flat place. Cutting off the Switch and plug straps. Installing the middle one and cut it off.
- Step 2: Please do not rotate 360 degrees after cutting off the straps, and Select for installation is Only up or down 90 degrees in a flat condition.
- Step 3: Please cut off the rest straps after finishing the installation, Thank you for vour understanding and Wish you a happy life.
CAUTION: Risk of electric shock
Correct Disposal of this product
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.
Konsumentkontakt
Arc E-commerce AB
Box 3124
13603 Haninge
Sverige