SONOFF PIR3-RF Motion Sensor User Manual

June 6, 2024
SonOFF

PIR3-RF
User manual V1.0
Motion Sensor

SONOFF TECHNOLOGIES CO., LTD.

The device can be operated intelligently by working with the SONOFF 433MHz RF Bridge to communicate with other devices.
The device can work with other gateways supporting 433MHz wireless protocol.
Detailed information is in accordance with the final product.

Operation instruction

  1. Download APPhttp://app.coolkit.cc/dl.html
  2. Pull out the battery insulation sheet The device has the version with battery and without battery(Battery model: CR2450).
  3. Add sub-devices
    Connect the Bridge before adding the sub-device.

Launch eWeLink APP, select the Bridge to be paired, tap “Add” and select “Alarm”, and you will hear a “Beep” that indicates the Bridge enters the pairing mode, then short press the pairing button on the device (or make the device detect the movement ) that the pairing is successful when the red LED keeps on for 1s and the Bridge makes a“Beep-Beep” sound.
If the addition failed, move the sub-device closer to the Bridge and try again.

Installation methods

Method1:

Method 2:

The motion sensor-based is not included, please purchase it separately.
Do not install on the metal surface, otherwise, it will affect the wireless communication distance.
The device’s weight is less than 1 kg. An installation height of less than 2 m is recommended.

Specifications

Model PIR3-RF
RF 433.92MHz
Power supply 3V button cell(Battery model: CR2450)
Detection Distance .8m (Indoor space)
Detection angle 100°
Working temperature -10°C-40°C
Working humidity 10-90%RH (non-condensing)
Material PC
Dimension 40x35x28mm

Product Introduction

LED indicator status instruction

LED indicator status Status instruction
Red LED stays on for 1 s A movement is detected
Red LED stays on for 5s Switched to the”home” mode
Red LED flashes twice Low-battery notification
Green LED stays on for 5s Switched to the “away” mode

Features

PIR3-RF is a 433MHz low-energy motion sensor that can detect the movement of objects in real-time. Connect it with the Bridge and you can create a smart scene to trigger other devices.

Application Mode

The device has“home” and“away” modes. The “away” mode is set by the factory default.
In the “home” mode, long-press the mode switching button for 5s until the LED indicator flashes red and holds 5s, this indicates the device enters the“home” mode.
In the “home” mode, long-press the mode switching button for 5s until the LED indicator flashes green and holds 5s, this indicates the device enters the“away” mode.
“Away” mode: Trigger a message and push to the app once every 5s.
“Home” mode: trigger and push a message once when no movement is detected for the 60s.

FCC Warning

Changes or modifications not expressly approved by the party responsible for compliance could avoid the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Hereby, Shenzhen Sonoff Technologies Co., Ltd. declares that the radio equipment type PIR3-RF is in compliance with Directive 2014/53/EU.The full text of the EU declaration of conformity is available at the following internet address: https://www.sonoff.tech/usermanuals

TX Frequency:
WiFi: 2412-2472MHz
RX Frequency:
WiFi: 2412-2472MHz SRD: 433.92MHz (RFR2)
Output Power:
14.43dBm(802.11b), 11.94dBm(802.11g), 11.96dBm(802.11n20)

Shenzhen Sonoff Technologies Co., Ltd.
1001, BLDG8, Lianhua Industrial Park, Shenzhen, GD, China
ZIP code: 518000 Website: sonoff.tech MADE IN CHINA

Documents / Resources

| SONOFF PIR3-RF Motion Sensor [pdf] User Manual
PIR3-RF, Motion Sensor, PIR3-RF Motion Sensor
---|---
| Sonoff PIR3-RF Motion Sensor [pdf] User Manual
PIR3-RF Motion Sensor, PIR3-RF, Motion Sensor, Sensor
| Sonoff PIR3-RF Motion Sensor [pdf] User Manual
PIR3-RF, Motion Sensor, PIR3-RF Motion Sensor
| SONOFF PIR3-RF Motion Sensor [pdf] User Manual
PIR3-RF, PIR3RF, 2APN5PIR3-RF, 2APN5PIR3RF, PIR3-RF, Motion Sensor

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals