Sonoff IFAN04-L Wi-Fi Smart Ceiling Fan with Light Controller User Manual
- October 30, 2023
- SonOFF
Table of Contents
DIY-IFAN04-L
Wi-Fi Smart Ceiling Fan with Light Controller
User Manual
IFAN04-L Wi-Fi Smart Ceiling Fan with Light Controller
Works with everything
Product Introduction
The
deviceweightis less than 1 kg. The installation height of less than 2 m is
recommended.
Features
This is a Wi-Fi smart controller for the ceiling fan with light that allows
you to remotely turn on/off the fan and light separately, adjust the fan
speed, schedule it on/off and share it with your families to control together,
etc. on the eWeLink App.
Operating Instruction
-
Power off Please install and maintain the device by a professional electrician. To avoid electric shock hazard, do not operate any connection while the device is powered on!
-
Wiring instruction
Please install protection devices before connecting the live wire. (e.g. fuses or air switches).
Make sure all wires are connected correctly. -
Download the eWeLink APP
http://app.coolkit.cc/dl.html -
Power on
After powering on, the device will enter the quick pairing mode during the first use, thenthe device makes two short beeps and one long beep.
The device will exit the quick pairing mode if not be paired within 3mins. If you want to enter the quick pairing mode again, press and hold the pairing button for 5s, or keep turning the device on and off repeatedly for 3 times (on-off-on-off-on) until the buzzer makes two short beeps and one long beep. -
Add the device
Tap “+” and select “Quick Pairing’, then operate following the prompt on the App.
Compatible Pairing Mode
If you fail to enter Quick Pairing Mode, please try “Compatible Pairing Mode” to pair.
- Press and hold the pairing button for 5s until the buzzer makes two short beeps and one long beep then release. Press the pairing button for 5s again until the buzzer makes a high frequency of beeps, which means the device has entered “compatible pairing mode”.
- Tap“+” and select” Compatible Pairing Mode” on App.
Select Wi-Fi SSID with ITEAD-***+ and enter the password 12345678, and then go back to eWelLink App and tap “Next”. Be patient until pairing completes.
Keep turning the device on and off repeatedlty for 5 times (on-off-on-off-on- off-on-off-on) to enter “compatible pairing mode”.
Remove the Battery Insulation Sheet 
After factory setting, RM433R2 remote
controller is bound to iFan04 by default. Simply remove the battery insulation
sheet to use. If the device connected to iFan04 is not controlled by the
remote controller, try to learn the remote controller again.
Learning Method for iFan04 and RM433R2 Remote Controller 
After powering
on iFan04, press any button on the controller until the buzzer makes a “beep”
sound within 5s, then all the buttons are learned successfully. If you do not
operate any step within 5s, power the device on again and repeat the above
operation.
This device canlearnup to 10 remote controllers. The 11th remote controller
will automatically cover the firstlearned one, and so on.
Specifications
| Model | iFan04-L, iFan04-H |
|---|---|
| Input | 100-240V AC 50/60Hz 5A |
| Output | iFan04-L: |
Light: 100-240V AC 50/60Hz 3A Max
Tungsten lamp: 360W/120V Max LED: 150W/120V Max
Fan: 100-240V AC 50/60Hz 2A Max
iFan04-H:
Light: 100-240V AC 50/60Hz 3A Max
Tungsten lamp: 690W/230V Max LED: 300W/230V Max
Fan: 100-240V AC 50/60Hz 2A Max
RF| 433MHz
Wi-Fi| IEEE 802.11 b/g/n 2.4GHz
App operating systems| Android & iOS
Working temperature| -10°C-40°C
Material| PC VO
Dimension| 116x55x26mm
Switch Network
Select the “Wi-Fi Settings” “inthe “Device Settings” interface on the eWeLink App to change. Re-establish Pairing
Method 1:
Press the “pairing button” on the device for 5s until the buzzer makes two
short beeps and one long beep then release, which means the device has entered
quick pairing mode, so it can be added in the eWeLink App again.
Method
2:
Press the “pairing button” on RM433R2 remote controller for 5s until the
buzzer makes two shortbeeps and one long beep then release, which means the
device has entered quick pairing mode, 50 it can be added in the eWeLink App
again. Method 3:
Keep turning the device on and off repeatedly for 3 times (on-off-on-off-on)
until the buzzer makes two short beeps and one long beep then release, which
means the device has entered quick pairing mode, so it can be added in the
eWeLink App again.
In quick pairing mode, press any button on the remote controller to exit the
current mode.
Factory Reset
Deleting the device on the eWeLink APP indicates you restore it to factory setting.
Remote Controller Specifications
| Model | RM433R2 |
|---|---|
| RF | 433MHz |
| Remote controller size | 87x45x12mm |
| Remote controller base size | 86x86x15mm (not included) |
| Power supply | 3V button cell x 1 (Battery model: CR2450) |
| Material | PC VO |
Remote Controller Introduction
iFan04 can be controlled by RM433R2 remote controller. After learning is
successful, you can control the device connected with iFan04 according to the
button instruction below. This featureis referred to as a short-distance
wireless communication, unrelated to Wi-Fi network communication. 
RF Clearing Method:
Press and hold the RF clearing button for 5s the buzzer makes “beep, beep”
sound after clearing is successful.
The buzzer of iFan04 n factory default setting will indicate you with the
“beep” sound whenyou turn on/off the fan, adjust the fan speed, and the device
enters pairing mode, but no a “beep” sound is made when you turn on/off the
light. You can press the “Mute” button on the paired RM433R2 remote controller
to silence the buzzer.
Common Problems
Fail to pair Wi-Fi devices to eWeLink APP
-
Make sure the device is in pairing mode. After three minutes of unsuccessful pairing, the device will automatically exit pairing mode.
-
Please turn on location services and allow location permission. Before choosing the Wi-Fi network, location services should be turned onand location permission should be allowed.
Location information permission is used to obtain Wi-Fi list information. If you click Disable, you will not be able to add devices. -
Make sure your Wi-Fi network runs on the 2.4GHz band.
-
Make sure you entered a correct Wi-Fi SSID and password, no special characters contained. Wrong password is a very common reason for pairing failure.
-
The device shall get close to the router for a good transmission signal condition while pairing.
FCC Warning
Changes or modifications not expressly approved by the party responsible for
compliance could avoid the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept anyinterference received,
including interference that may cause undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
This equipment should be installed and operated with minimum distance20cm
between the radiator & your body. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
Note:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuantto part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmfulinterference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connectthe equipmentinto an outlet on a circuit different from that to which the receiver is connected.
- Consultthe dealer or an experienced radio/TV technician for help.
Hereby, Shenzhen Sonoff Technologies Co., Ltd. declares that the radio
equipment type iFan04-L, iFan04-H is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the
following internet address:
https://sonoff.tech/usermanuals
Shenzhen Sonoff Technologies Co., Ltd.
1001, BLDGS, Lianhua Industrial Park, shenzhen, GD, China
ZIP code: 518000
Website: sonoff.tech
MADE IN CHINA
Documents / Resources
|
Sonoff IFAN04-L Wi-Fi Smart Ceiling Fan with Light
Controller
[pdf] User Manual
IFAN04-L Wi-Fi Smart Ceiling Fan with Light Controller, IFAN04-L, Wi-Fi Smart
Ceiling Fan with Light Controller, Smart Ceiling Fan with Light Controller,
Ceiling Fan with Light Controller, Fan with Light Controller, Light
Controller, Controller
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>