SNORE CIRCLE YS20 Sleep Breathe Monitor User Manual
- June 6, 2024
- SNORE CIRCLE
Table of Contents
Manufacturer: WFLY Electronics Co., Ltd.
Address: Unit 2103-2104, Changhong Sci-tech Building, Science and Technology
Park, Nanshan District, Shenzhen, China
Service email: kf@wfly.cn
Hereby, we WFly Electronics Co., Ltd. declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. This product can be used across EU member states. The adapter shall be installed near the equipment and shall be easily accessible. The operating temperature of the device is between -10°C to 50°C.
0verview
Snore Circle VS20 (hereinafter “this device”) is a smart wearable device specially designed to monitor breathing at home. It allows you to monitor your breathing snoring, sleep duration, sleeping position, and other data in real- time and provides personalized suggestions to help improve your quality of sleep. We hope this device can help you sleep better!
Introduction
This device is composed of the main component (including face mask), straps and the magnetic charging cable.
Product parameters
[ Product name] : sleep breathe
[ Brand 1 : Snore Circle
Model ] : YS20
[ Size of main component ] : 29.4’24.5’11.5MM
[ Size of mask 1 : 105.0’95.8’55.6MM [ Weight ] : 18.5g
[ Battery capacity : 3.N/55mAh
[ Run time I : About 16 hours
[ Product components ] : Main component (including face mask) xl, User Manual
xl, Quick Start Guide xl, charging cable xl, white strap (5) x4, white strap
(M) x4, white strap (L) x4.
Power On/Off
Press and hold the power button for 3 seconds to turn on the device. The power
indicator will turn on for 10 seconds and the Bluetooth indicator will flash
for 10 seconds before turning off.
Power Off
Press and hold the power button for 3 seconds to turn off the device. The
power and Bluetooth indicators will turn off when the device is powered off.
(1) The power indicator will automatically turn off after 10 seconds to save
power. You can press the power button to turn it on again.
(2) Press the power button to check the status of the device. A solid light
indicates the device is working.
Battery Instructions
(1) Chocking the battery level You can determine the battery level by checking the color of the power indicator. A yellow light indicates the device has a low battery and requires charging.
A green light indicates the device has sufficient battery and does not require charging.
Pair the device with the sleep breathe App and go to the Monitor interface to
view the specific battery level
(2) This device uses a rechargeable lithium-polymer battery.
(3) It takes approximately 2 hours to fully charge the battery.
(4) Connect the magnetic charging cable to the USB port to charge the device.
A power indicator will flash when the device is charging and stay on when it
is fully charged.
App download
How to download:
(1) iPhone: Search for sleep breath via the App Store to download and install
the app. (2) Android: Search for Sleepbreathe in Google Play to download and
install the App. (3) Scan the QR code below.
http://qrcode.vvfly.cn/ys20_app.htm
Pairing
a) Open the sleep breathe App and ensure Bluetooth is on.
(2) The Bluetooth indicator will flash for 10 seconds when the device is
powered on. indicating that the device is ready for pairing.
(3) Hold your phone close to the device and follow the instructions on the App
to pair the device. A solid Bluetooth light indicates pairing is successful.
(4) If your device cannot be found, please check it is powered on, move it
close to your phone, and try again. Follow the instructions on the App to pair
the device.
Pairing your device with the app allows you to view device data.
(1) Only phones with 105 8.0 or above or Android 4.3 or above are supported.
(2) Due to operating system requirements, some Android phones require you to
grant the App access to your location. Access to Bluetooth is required to
search for the device. (3) The device only needs to be paired once. Unless
otherwise unpaired, it will automatically connect to your phone the next time
it is used.
(4) The device will automatically reconnect with the App when it is turned on
and close to your phone.
App Functions
(1) Ensure your phone’s Bluetooth is enabled and the device is turned on.
(2) Open the sleep breathe App and move your phone close to the device.
(3) Click “Pair” to pair the device.
(4) You can start monitoring your sleep when the device status is “Connected”.
(5) The Monitor interface displays real•time sleep data such as suspected
respiratory events and snoring.
(6) The Reports interface allows you to view the quality of your sleep and
statistical analysis. Detailed sleep data and suggestions are provided based
on the data report.
(7) You can view the definitions for technical terms on the Device interface.
Wearing Instructions
Three types of straps are included with this device. Please choose the type
that is right for you. Avery loose or tight strap will lead to inaccurate
monitoring data. The strap should be slightly taut when worn.
(1) Choose two white straps of the same length and feed them through the round
holes on each side of the mask. Press the end of the straps to flatten them.
(2) Position the mask with the white straps behind your ears. When you pull the mask forward, the distance between the tip of your nose and the top of the mask should be roughly the width of three fingers
(3) Reposition the mask to your face to start monitoring.
FAQ
(1) Does the device have to be connected to the App when used?
A: Yes, the device must be connected to the App during use. The App can
display monitored data in real-time and store previous data, so you can check
your sleep data at any time. Once paired, your device will automatically
connect to your phone when turned on.
(2) Is the App compatible with all phones?
A: The Apo supports phones with either i05 8.0 or above or Android 4.3 or
above. It is currently compatible with 99% of phones on the market.
(3) Does the power indicator stay lit once powered on?
A: No. Once the device is powered on. the power indicator and Bluetooth
indicator will turn on for about 10 seconds before automatically turning off.
Press the power button to turn on the power indicator and Bluetooth indicator
for another 10 seconds.
(4) How do I know if the device is working?
A: The Monitor interface in the App will display real-time data when the
device is operating.
(5) How long does it take to charge the device and how long can it be used for
once fully charged?
A: It takes about two hours to fully charge the device, after which it can
typically be used for up to 16 hours. If you use the device for more than 8
hours a day, it is recommended to charge it once a day.
(6) How do I select the right strap for me?
A: Three types of straps are included with this device. Please choose the one
that is right for you. When you pull the mask forward. the distance between
the tip of the nose and the top of the mask should be roughly the width of
three fingers. If the data report shows that the device is misplaced or falls
off for a prolonged period of time, it is recommended to use a smaller strap.
(7)Can the App run in the background?
A: Yes, it can. However, to improve your user experience, it is not
recommended to run it in the background as this may increase the risk of real.
time monitoring being interrupted by other programs.
(8) Why the ideal working temperature of the equipment is room temperature
(25t)?
A: A temperature sensor is used to collect respiratory data from the user’s
mouth and nose. This sensor is extremely sensitive to the ambient temperature,
which may affect the accuracy of the collected data.lf the temperature is too
low, the mask will produce water droplets.
Troubleshooting
(1)The device doesn’t turn on/off Try charging the device using the USB cable.
if the problem persists. please contact the manufacturer.
(2) The device cannot be charged Please check that the magnetic charging cable
is properly connected and that the power adapter works. if the problem
persists. please contact the manufacturer.
(3) Real-time data is not displayed on the App. Please restart the device and
pair it with the App again. How to restart the device: Press and hold the
power button for 3 seconds to turn off the device, then turn it on again and
reconnect it to the app. How to restart the app: Close the app from the
background processes and open it again.
(4)The device cannot connect to the App Please restart the device and your
phone’s Bluetooth and try again.
Precautions
(1) The ideal working temperature of the equipment is room temperature (25’C),
and the storage temperature is -10’C • SOY. (2) Keep the main component away
from direct sources of airflow. such as fans.
(3) Keep the device away from sources of fire or high temperatures (e.g.
electric heaters. microwaves, ovens. etc.).
(4) Keep the device away from high impact or strong vibration to avoid damage.
(5) Do not use chemicals, detergents, etc. to clean the device. Keep the
device dry; do not wash it.
(6) Do not attempt to remove or replace the built.in lithium polymer battery
on your own so as to avoid damage.
(7) Do not throw the device into the fire to prevent the possibility of an
explosion.
(8) This device is not a toy. Please keep it out of the reach of children to
prevent accidental swallowing or other dangerous incidents.
(9) The device cannot be used while charging.
(10) The adapter or other power output for the charging dock must be less than
S watts and comply with local safety standards.
(11) please unplug the special magnetic charging cable as soon as charging is
complete to avoid any potential danger.
(12)Charge the battery within a temperature range of St to 4St.
(13)When the device and its accessories reach the service life, they should be
disposed of in accordance with the relevant local laws and regulations. Do not
discard them at will. (14) rf you experience any discomfort while using this
device, stop using it immediately. (1S)Read the instructions carefully before
using this device.
This product is not a medical device. It only provides data for reference and
does not diagnose diseases.
After-sales Service
(1) This product is covered under a one. year warranty from the date of purchase. (2) Artificial damage is not covered by warranty.
Declaration of Hazardous Substances or Elements
In accordance with the relevant regulations and requirements of the Administrative Measures on the Control of Pollution Caused by Electronic Information Products of the People’s Republic of China, the following table includes the component names of the electronic product and the toxic and hazardous substances contained within.
Component Name|
Toxic and Hazardous Substances and Their Concentration
---|---
Lead (Pb)| Mercury (Hg)| Cadmium (Cd)| Hexavalent
Chromium
(Cr6+)| Polybrominated
Biphenyls
(PBB)| Polybrominated
Diphenyl Ethers
(PBDE)
Housing| 0| 0| 0| 0| 0| 0
Buttons| 0| 0| 0| 0| 0| 0
User Manual| 0| 0| 0| 0| 0| 0
Standard Battery| 0| 0| 0| 0| 0| 0
face mask| 0| 0| 0| 0| 0| 0
straps| 0| 0| 0| 0| 0| 0
pac Package DOX| 0| 0| 0| 0| 0| 0
Metallic components| 0| 0| 0| 0| 0| 0
- -0″ indicates that the concentration of the hazardous substance in all homogeneous materials in the component is below the limit requirement of the S.I/T11363-1006 standard.
- • x” indicates that the content of the toxic and hazardous substance in at least one homogeneous material of the component exceeds the limit requirement of the 5J/111363-2006 standard.
Environmental Friendly Use Period
‘ The above use period is based on normal operating conditions (temperature/humidity) Product Standard: Q/YZFD 006-2020
Component | Environmental Friendly Use Period |
---|---|
Sleepbreathe |
FCC Caution
§ 15.19 Labelling requirements. This device complies with part 15 of the FCC
Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference. and (2) this device must accept any
interference received, including interference that may cause undesired
operation.
§ 15.21 Information to the user. My Changes or modifications not expressly
approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
§ 15.105 Information to the user.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device. pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions. may cause harmful interference to radio
communications. However. there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception. which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the Me Meowing measures: -Reorient or relocate
the receiving antenna. -Increase the separation between the equipment and
receiver. Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected. -Consult the dealer or an experienced
radio/TV technician for help.
‘ RF warning for Portable device:
The device has been evaluated to meet general RF exposure requirements. The
device can be used in portable exposure conditions without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>