VOLVO A2DIY-VOL CD Changer Controlling Radios Installation Guide

VOLVO A2DIY-VOL CD Changer Controlling Radios

PRODUCT SAFETY & DISCLAIMER

READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLING, FAILURE TO DO SO MAY CAUSE PERSONAL INJURY OR DAMAGE TO PRODUCT AND/OR PROPERTY

• This installation guide is provided as a GENERAL installation guide, some vehicles vary and may require additional steps. We do not accept responsibility for third party labor charges or modifications. Exercise due-diligence when installing this product.
• We do not accept any responsibility for vehicle damage or personal injury resulting from the installation of this product.
• Careless installation and operation can result in equipment damage.

Requirements:
Radio with cd changer controls

Introduction

Many Volvo car owner’s adamant about keeping cars system as stock possible, will be thrilled with the A2DIY-VOL kit which adds modern Bluetooth features without changing the look and feel of dashboard components. Features Bluetooth Hands-Free and music streaming from any Smartphone with A2DP and HFP support. remote control for both Apple and Android devices allows users to track up/down, pause, increase/decrease device volume, answer/end calls and more. Optional Fast charging kit to keep devices fully charged while on the road. Newest version (10.3), AUX input is no longer offered. Support for Bluetooth 5.0 and Call number announcement on car speakers. Keep the radio and car you love while enjoying Bluetooth features only available on newer cars. For more details, see Frequently Asked question at the end of this guide.

Installation

Warning : Although not critical, we recommend disconnecting battery. Keep in mind, most Volvo radios are coded and will not operate without code. Radio code must be available for radio to operate upon reconnection

1. Remove radio by pressing both spring-loaded release tabs as seen in Fig. 1
2. Place finger inside release ring and pull outward as seen in Fig. 2
3. Connect harness 8-pin plug (See Fig. 3) to “CD” port (See. Fig. 4). Factory CD changer (if present) must be disconnected.
4.  Use clip to secure microphone to headliner or visor (See Fig. 5)
5.  Route microphone cable (10 ft. long) down side pillar, under steering column and into radio cavity,
6.  Connect microphone right angle plug to module “MIC” input. (See Fig. 6) Wind noise will negatively affect phone audio. Users are advised to install microphone away from wind/ventilation ducts etc.
7. Tap YELLOW wire from installation harness to YELLOW/PURPLE (Battery supply) wire on radio harness or another source for 12V battery accessory supply (See Fig. 7)

Secure module and proceed to next section.

Optional charging kit

Optional USB charger can be added to the A2DIY-HON. Should you decide to add this option, we suggest one of 3 connecting options:

1.  Flush to dash/panel requires drilling a ¾” hole
2.  Flush with Support bracket (Mount USB terminal wherever your installation demands without drilling)
3.  USB port- (default)

Features

• Input voltage: 6-24V DC
• Working current: 30mA
• Default output voltage: 5V or 3V-12V (if device supports it)
• Max output power: 24W

Should you decide to add the USB Port, we suggest 2 mounting options:

•  Flush to dash/panel requires drilling a ¾” hole in the dash
•  Flush with Support bracket (use this option to mount USB terminal wherever your installation demands without drilling)
•  Flush to Dash or Panel (requires drilling)

1. Drill a ¾” hole in the dash or panel using a step drill bit or equivalent (See Fig. 10)
2.  Insert USB male terminal through the ¾” hole created in step 1 and connect to module USB port (See Fig. 12)
3.  Push USB head (See Fig. 13) until it snaps in place and flush with mounting surface (See Fig. 14)
4. Tuck and secure any extra wire from moving parts and test operation

USB with Bracket Mount (No drilling)

1. Locate a flat surface at location of choice within 3.2 ft. of radio and mount USB support bracket (See Fig. 15) to surface using adhesive/tape or screws.
2. Insert the 6 ft. USB male terminal through bracket hole (See Fig. 16) and connect to Module USB port (See Fig. 12)
3. Push USB head until it snaps in place and flush (See Fig. 17)
4. Connect BLACK wire to ground (radio chassis or harness ground wire), and RED or YELLOW to accessory or battery supply. Your choice!Accessory connection: charging is possible with ignition/engine “ON”. Battery connection: charging is possible at all times. Tuck away any extra wires and verify BLUE LED is lit.

Pairing module

Pairing varies among devices but basic steps are the same. This process is done upon initial install and will not have to be repeated

1.  Turn Ignition and radio “ON” Blue LED in adapter peephole will flash (pairing mode)
2.  On A2DP device: go to Settings, Wireless & Networks, Bluetooth Settings
3.  Select Bluetooth and turn on, select Bluetooth settings
4.  Tap Scan for devices.
5.  Wait for Bluetooth device name (See below) to appear and select it. Once paired Blue LED inside peephole flashes once every 2 seconds and confirmation tone is heard on car speakers

One connection
The A2DIY-VOL connects to one device at a time. You must disconnect/unpair first device before pairing a second, or simply disable Bluetooth on first device.
Notes:

1.  New! On incoming calls, ring tone and call number announced on car speaker. Additional tone (static) heard during call number announcement (this is normal)
2. Media remote does not control Volvo radio functions.

Media remote button

Pairing Bluetooth remote button: Ensure Bluetooth is enabled on your device (e.g., Smartphone/Tablet etc.) Press and hold pause/play button (See Fig. 18) until Blue LED flashes Scan smartphone for available devices and select BT009 from list. (Blue LED turns off).

Installation
Attach button to steering wheel (includes holder) or dashboard using included double sided tape – your choice!

Operation

Once paired with smartphone/Tablet, users may perform the following functions on iOS devices with Bluetooth 3.0 and later or Android 4.0 or later. Media remote functions do NOT apply to Volvo radio.

Charging

Media button built-in rechargeable 200mAH battery may last up to 10 days. Use supplied USB cable to charge. Red LED indicates charging; Full charge is reached  after 2 hours at which time LED turns off.

Volvo Bluetooth comparison chart

When radio is in CD changer (Bluetooth Mode)  Optional

Operation

1.  Turn ignition to ACC and radio “ON”
2.  Press radio “CD” CHG” or “CHGR” button to enter “Bluetooth” mode
3.  Launch smartphone music streaming application
4.  Use media remote to change tracks, adjust device volume, pause playback, answer/end calls etc.
5. Place phone call or ask someone to call.
6.  Adjust call volume with media remote, steering wheel controls or radio volume knob.
7.  To end call press media remote, Pause/Play
8.  If correct operation is confirmed go ahead and reinstall radio.

Warning: Playlist and Track selection is NOT possible using Volvo radio buttons. Use audio device built-in controls and display or media remote  to access and control audio files and applications.

Notes:
Adding additional load to electrical system in older vehicles can result in alternator whine or similar noise. We recommend installing a noise filter

Frequent ask questions & troubleshooting

1.  What’s the difference between A2D-VOL and A2DIY-VOL? See Bluetooth comparison chart on previous page. Major difference is A2D-VOL does not support hands-free calls
2.  Does the A2DIY-VOL work on all Volvo radios? NO; works only on Volvo “SC” and select “CT” radios with CD changer controls.(non-changer controlling radios are not supported)
3.  Can I control Smartphone from radio buttons? NO; use Smartphone built-in controls and display to operate device, or included remote control. Radio volume button is used to set playback level.
4.  Can I pair or save more than one device to the A2DIY-VOL? YES; pair more than one device, but only one can be active at a time.
5.  What happens if streaming and call comes in? Streaming will mute, call number announced on car speakers, call rings on car speakers. To be connected with caller simply press media remote pause/play button. To end call press, pause/play. Streaming resumes.
6. Can I connect module to the CD changer plug in trunk/hatch? NO; Trunk/hatch location is not ideal for connecting Hans-free module.
7.  During call number announcement, there is static like noise in background. Is this normal? YES. It is normal for background hiss/tones during call number announcement. The background tone/hiss will cease as soon as announcement ends or call is answered.

Disclaimer

•  This product has no affiliation with Volvo.
•  We’re not liable for misuse of this product.
•  We recommend professional installation.

Email support@discountcarstereo.com
© 1995-Oct-21 Discount Car Stereo All rights reserved. Information in this document is subject to change without notice. Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders.

References

• 📧support@discountcarstereo.com
• Discount Car Stereo > Accessories > BLU-RMT Bluetooth Media remote control for Android and iOS devices Zoom
• Discount Car Stereo > Accessories > NF3A In-line Noise Suppression Filter (3A)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>