Vision X TREM-85246XX Tremor XD LED Beacon Large

Product Information

• P/No. TREM-85246XX
• Color: X (Please refer to the color code for specific color)

Features:

• Tough diecast aluminum housing
• Virtually unbreakable polycarbonate lens
• Military standard vibration resistance
• Upward-facing LED for increased awareness from above
• Selectable Day/Night mode
• Flash synchronization of multiple beacons
• SAE and California Title 13 approved

Product Usage Instructions

WARNING:
Read carefully and understand all instructions before operating.

Follow these guidelines to ensure safe usage:

• It is not recommended to use magnetically mounted warning devices on the outside of a vehicle in motion. Usage is at the sole risk and responsibility of the user.
• Risk of electrical shock; do not use in an environment with gas, combustible or explosive materials, or hot objects.
• Do not open, repair, or modify the product.
• Use only under the recommended voltage and frequency requirements.
• Do not look directly at the light, as this will result in dazzling.
• Minimum distance from lighted objects should be 0.1m.
• The specification in this manual is based on standard lab testing, different environments may influence the data.
• California Proposition 65 Warning: This product contains chemicals known to the State of California to cause cancer, and birth defects or other reproductive harm. For more information, please visit www.P65Warnings.ca.gov

Installation:

1. Prepare a suitable area on the vehicle’s surface by wiping it clean to prevent scratching.
2. Drill a 10mm (3/8) hole into the surface for the wires to exit through for connection to a power source. Alternatively, the wires can be directed through the side of the lamp’s base for connection to a power source.
3. Place the mounting base in position on the vehicle’s surface. Using the plate as a template, drill three holes for fitment and secure to the surface using the supplied mounting bolts. A mounting pad is included and can be installed between the surface and the mounting plate.
4. Route the wires as planned in step 2. Connect the red (+) wire to 12/24VDC and the black (-) wire to the ground. Test.
5. Note: If the mounting plate is not required, use the lamp’s base as the template when drilling holes for fitment to the vehicle.

Wiring:
Follow these instructions for wiring:

• Strobes together for synchronization
• WHITE: Apply to +VDC for low/high power switching
• All units must be set to the same pattern

Synchronized Flashing:
For Simultaneous or Alternating Flash:

1. Apply +VDC to RED and YELLOW wires simultaneously, then remove YELLOW.
2. Note: For flash patterns #1~#3, Group 1 Units will flash in an anti-clockwise rotator; Group 2 Units will flash in the clockwise rotator.

Flash Patterns:

• 4 SINGLE FLASH

• 8 STEADY ON

WARNING

Read carefully and understand all instructions before operating.

• It is not recommended to use magnetically mounted warning devices on the outside of a vehicle in motion. Usage is at the sole risk and respondibility of the user.
• Risk of electrical shock; do not use in an environment with gas, combustible or explosive materials, or hot objects.
• Do not open, repair or modify.
• Use only under the recommended voltage and frequency requirements.
• Do not look directly at the light, as this will result in dazzling.
• Minimum distance from lighted objects 0.1m.
• The specification in this manual is based on standard lab testing, different environments may influence the data.
• California Proposition 65 Warning: This product contains chemicals known to the State of California to cause cancer, and birth defects or other reproductive harm.

For more information, please visit www.P65Warnings.ca.gov.

FEATURES

• Tough diecast aluminum housing and virtually unbreakable polycarbonate lens.
• Military standard vibration resistance.
• Upward-facing LED for increased awareness from above.
• Selectable Day/Night mode.
• Flash synchronization of multiple beacons.
• SAE and California Title 13 approved.

INSTALLATION

1. Prepare a suitable area on the vehicle’s surface by wiping it clean to prevent scratching.
2. Drill a 10mm (3⁄8″) hole into the surface for the wires to exit through for connection to a power source. Alternatively, the wires can be directed through the side of lamp’s base for connection to a power source.
3. Place the mounting base in position on the vehicle’s surface. Using the plate as a template, drill three holes for fitment and secure to the surface using the supplied mounting bolts. A mounting pad is included and can be installed between the surface and the mounting plate.
4. Route the wires as planned in step 2. Connect the red (+) wire to 12/24VDC and the black (-) wire to the ground. Test.

Note: If mounting plate is not required, use the lamp’s base as the template when drilling holes for fitment to the vehicle.

1. Drill holes 1 2 3 4 on the mounting surface for wire exit and mounting bolts.
2. Secure the beacon onto the mounting surface with mounting bolts.
3. Note: Mounting holes 1 2 3 are different from 1’ 2’ 3’. Check and mark the correct location before drilling.

WIRING

• RED: To 10–33V DC(+) Fuse at 3A
• BLACK: To chassis/ground (-)
• YELLOW: Flash pattern change +VDC. Connect Yellow wires of strobes together for synchronization
• WHITE: Apply to +VDC for low/high power switching

All units must be set to the same pattern

WIRING DIAGRAM

SYNCHRONISED FLASHING

For Simultaneous or Alternating Flash:

1. Apply +VDC to RED and YELLOW wires simultaneously, then remove the YELLOW wire to enter Grouping Mode, units will display short flashes:
   • Single flash = Group 1
   • Double flash = Group 2
2. To change Group, momentarily apply +VDC to YELLOW wire:
   • Both units in the same Group will flash together.
   • Two units in the different Groups will flash alternately.
3. Save and exit Grouping Mode by disconnecting all power.

Note: For flash pattern #1~#3,

• Group 1 Units will flash in an anti-clockwise rotator;
• Group 2 Units will flash in the clockwise rotator.

FLASH PATTERNS

SPECIFICATIONS

(-30°C – + 80°C)

| ECE Ratings| ECE R10
Weight| 1kg / 2.2lbs| EMC Approval| CISPR25 Class 3
 | SAE Compliance| J845 Class 1, W3-1

WARRANTY TERMS & CONDITIONS

1. Warranty items will be replaced or repaired to working condition and returned without cosmetic alterations.
2. Proof of purchase is required to validate all warranty claims. The warranty period is valid starting from the original date of purchase.
3. All products must have been purchased through a Vision X Authorized Dealer/Reseller to be eligible for warranty.
4. Damage resulting from any improper installation, accident, abuse, neglect, or normal wear is not covered under warranty.
5. Any product used in mining applications is warranted for one year only.
6. Actions that void the warranty include:
   • Opening of the lighting fixture
   • Cutting any connectors or cords
   • Broken Glass
   • Damage caused by physical abuse
   • Lights operated in environments outside their stated specifications*
7. All customer warranties should be handled through the Dealer/Reseller the product was originally purchased from. The customer is responsible for delivery to Vision X Returns in Auburn, Washington.
8. If a product is deemed not covered under warranty, the customer will be responsible for the return shipping charges.
9. Items not covered under warranty can be repaired at the customer’s expense for parts and labor, at the discretion of Vision X Lighting, who will provide an estimated repair cost before proceeding with the repair.

Distributed by:
Vision X Lighting 1601 Boundary Blvd. Auburn WA, 98001 USA Made in Taiwan.

For more info visit
www.visionxusa.com.

References

• P65Warnings.ca.gov
• Vision X Lighting USA – Global LED Lighting Systems

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>