XC60 Wall Box Selected By Volvo Cars User Guide

Wall box selected by vlovo cars

Copyright and trademarks
Copyright 2024 eSystems MTG GmbH
All rights reserved.
Subject to availability and technical modifications.
All hardware and software names used are trade names and/or registered trademarks of the relevant manufacturers:
Issued by: 01/2024
Revision: 3.0

YOUR Wallbox

With permanently connected charging cable With socket

Front Panel

About this document

To perform all the steps described here, the Wallbox must be fully configured and ready for operation. For  information on this, see the Assembly and installation  instructions. For further information, see Additional information.
Charging a vehicle without authentication  (Free-Charging)
No approval is required. Connect the charging cable and charge: This is the default factory setting.
Prerequisites

• Charge level LED (2) is lit in white.

• Operating / error status Led (1) is lit in white.

• If the LEDs are not lit, briefly press the button  (1).
  1.  Only for version with socket:
  Plug the charging cable into the socket on the Wallbox.
  2.  Plug the charging cable into the vehicle connection.

• The charge level LED (2) initially pulses white while vehicle identification is in progress.

• When the charge level LED (2) is pulsing  green, the charging process has been started  successfully.

• When charging is complete or the vehicle is  fully charged, the charge level LED (2) is continuously lit in green.
  3.  If an error occurs, fix the error as described in the operating instructions.

Connecting to the Wallbox using the web app

Follow the steps below to use the web app:

1. Keep the access letter to hand.

2. Find the list of available WiFi devices on the laptop,  tablet or smartphone.

3. Select the Wallbox from the list of available WiFi  devices using the WiFi code (SSID) from the access  data letter.

4. Establish a connection with the selected Wallbox.
   If a connection could not be established, see  Assembly and installation instructions, section  Commissioning: No connection to web app established via WiFi.

5. Enter the WiFi password for the Wallbox (network  key) from the access data letter.

6. When the connection has been established successfully, open the web browser.

7. Enter the host name of the Wallbox from the  access data letter in the address bar. The login  area is displayed in the web app with a login  option.
   Note
   When accessing the web app, the web browser  may display a warning stating that the page  poses a security risk or that a secure connection  cannot be established (depending on the  browser). Depending on the web browser, the “Advanced” button can be used to enable access  to the web app via an additional button or link.

8. Select standard user as the user role.
   Note
   System settings can only be made as the Service user, see operating instructions.

9. Enter the password for the standard user (from  access data letter).
   After a successful login, the Overview is displayed.

There are now two quick start options for charging the  vehicle:

• Access protection remains disabled, vehicle is  charged without authentication, see Charging a vehicle without authentication (Free-Charging).
• Enable access protection and register the RFID  chip, see Registering the RFID chip.

Registering the RFID chip

DANGER
Risk of injury due to RFID sensor for persons with cardiac pacemaker or defibrillator

• If you use a cardiac pacemaker, maintain a distance of at least 60 cm from the RFID sensor on  the front panel.
• If you use a defibrillator, maintain a distance of  at least 40 cm from the RFID sensor on the front  panel.

1. Log in as a service user.
   In the web app, select Vehicle management,  Approved list in the navigation.

2. Disable Free charging.

3. Select Add RFID chip.

4. Hold up the RFID chip to the RFID sensor (5) on the front panel of the Wallbox.

5. Wait until the RFID chip has been identified.
   A beep sounds and the RFID LED (5) lights up green briefly as soon as the RFID chip has been successfully identified.

6. Give the RFID chip a name of your choice in the  web app.

7. Select Add to approved list.
   The RFID chip is added to the approved list and is  displayed as a registered chip in the Approved list screen.

Charging a vehicle with an RFID chip
Prerequisite
Charge level LED (2) is lit up white (no vehicle identified yet).

1. Only for version with socket:
   Plug the charging cable into the socket on the Wallbox.

2. Plug in the charging cable on the vehicle.
   The charge level LED (2) pulses white (vehicle identification in progress).
   The charge level LED (2) pulses yellow (waiting for authentication).

3. Hold the RFID chip up to the RFID sensor (5) on  the front panel of the Wallbox and wait for identification:
   A beep sounds and the RFID LED (5) lights up green briefly as soon as the RFID chip has  been successfully identified.
   When the charge level LED (2) is pulsing  green, the charging process has been started  successfully.
   When charging is complete or the vehicle is fully charged, the charge level LED (2) is continuously lit in green.

Further information
The Wallbox provides the following additional authentication methods, see operating instructions:

• Plug & charge
• Auto charge
• Approval by remote control
• Approval in the web app

When using OCPP, the backend operator’s server  issues the charging approval remotely.

Additional information

For the operating instructions, assembly and installation instructions,  the full text of the EU Declaration of  Conformity and other documents, see https://public.evse-manuals.com/volvo/index.html
EU conformity
eSystems MTG GmbH hereby declares that the following radio equipment types GHO22E202x,  GHO22E213x, GHO22E223 comply with Directive  2014/53/EU.
x may represent any letter.
The Wallbox is used for charging electric vehicles that comply with the generally applicable standards and directives for electric vehicles.
The Wallbox is suitable for stationary use indoors and outdoors and in private and semi-public spaces for operation within the defined electrical and environmental specifications.

Safety

To ensure safe operation of the Wallbox, observe the requirements for the target group and the intended  use, along with the safety instructions for operation,  see operating instructions.

eSystems MTG GmbH
Bahnhofstr. 100
73240 Wendlingen
Germany
www.esystems.de

Documents / Resources

| VOLVO XC60 Wall Box Selected By Volvo Cars [pdf] User Guide
XC60 Wall Box Selected By Volvo Cars, XC60, Wall Box Selected By Volvo Cars, Selected By Volvo Cars
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>