kogan KA52CWCLRWA Smarter Home 40W 90+ Cri Natural Cool and Warm White Ceiling Light User Guide

KA52CWCLRWA Smarter Home 40W 90+ Cri
Natural Cool and Warm White Ceiling Light
User Guide

SAFETY & WARNINGS

• WARNING: The ceiling light must be installed by a licensed electrician.
• The ceiling light is rated 220-240V. Ensure to the voltage supply at your home corresponds to this.
• The LEDs of the ceiling light cannot be replaced. Do not disassemble the product.
• The ceiling light generates heat during operation. Keep the surrounding air convection for heat dissipation.

COMPONENTS

OVERVIEW

Ceiling Light

Metal Chassis

Remote Control

light will automatically return the status before it was turned off.
• Additionally, this button can be used to pair/unpair the remote control with the ceiling light. For instructions, see the Remote Control section of this user guide.
3| Increase Brightness| • Short press to increase the brightness step by step.
• Long press to increase brightness gradually.
4| Warm Light (3000K)| • Short press to increase the color warmth step by step.
• Long press to increase the color warmth gradually.
5| Night Status| • Set the night light status to Warm Light (3000K) with 10% brightness.
• Press any key to release from this function.
6| Cyclic Conversion| Set the light setting to cyclic conversion:
Cool Light – Warm White Light – Medium Warm Light
7| Automatic Turn Off| • Short press this key to set the ceiling light to turn off automatically after 30 minutes.
• Press any other key to release from this function.
8| Decrease Brightness| • Short press to decrease the brightness step by step.
• Long press to decrease brightness gradually.
9| Cool Light (6500K)| • Short press to decrease the color warmth step by step.
• Long press to decrease the color warmth gradually.
10| Medium Warm Light (4000K)| Press this key to set the ceiling light to medium warm light of 4000K with lower brightness.
11| Power Off| Short press this key to turn off the ceiling light.

INSTALLATION

Note: The ceiling light must be installed by a licensed electrician.

Step 1:

• Open the package and remove the ceiling lamp. Pull the metal chassis outward and remove it.
• Turn off the power supply to avoid electric hazards.
  

Step2A:
To install the light directly into the ceiling:

• Pass the power cable through the threading hole of the metal chassis.
• Fix the metal chassis to the ceiling with expansion screws and self-tapping screws.
• Ensure the metal chassis is fixed firmly.

Step 2B:
To install the light into an installation point mounted on the ceiling:

• Ensure the installation point is mounted firmly.
• Pass the power cable through the threading hole of the metal chassis.
• Fix the metal chassis to the mount using the self-tapping screws.
• Ensure the metal chassis is fixed firmly.

Step 3:

• Strip 8-10mm of the power cable as shown in the image.
  

• Insert the stripped end of the power cable into the metal chassis interface.

• Check that the cable is secure and is aligned.

• To remove the power cable, press the red button on the metal chassis and remove the power cable.

Step 4:

• Align the side of the ceiling light so that the opening of the groove is towards the metal chassis. Slide the ceiling light into the metal chassis completely.
  

• Push it gently against the ceiling level and you will hear a click sound.

• Ensure the ceiling light is fully seated.

CONNECT TO SMARTERHOME™ APP

Install App
Download the “Kogan Smarter Home” app from the Play Store (Android) or App Store (iOS).
Register
If you do not have a Kogan SmarterHome™ account, register or sign in with a verification code sent by SMS.
To register:

1. Tap to enter the registration page.
2. The system automatically recognizes your country/area. You can also select your country code manually. Enter your email address and tap ‘Next.’
3. Alternatively, you can select ‘Register by the mobile number’ and enter the verification code sent to you by SMS.
4. Create a profile on the next page to define your location and room.
   

Set device in pairing mode
When the device is first turned on, it may automatically enter pairing mode which is indicated by the ceiling light flashing rapidly.
If not automatically in pairing mode when powered on, you can manually set the device in pairing mode by turning on and turning off the wall switch 3  times until the ceiling light starts flashing rapidly.

Add device through the network

1. Once registered, tap “+” in the upper right corner of the app’s home page to add a new device through the network.

2. Select the product type from the list of options in the opp (Lighting >Indoor Bulb).

3. Ensure that the device is in pairing mode, with the ceiling light flashing rapidly, and tap “Confirm light is rapidly flashing”.
   

4. Upon successfully confirming pairing mode, enter your Wi-Fi details. It is important that your SmarterHome™ device and the opp are connected to the same Wi-Fi network during setup.

5. The device will commence the pairing process and connect to the opp. Ensure your Wi-Fi router, mobile phone, and the SmarterHome™ device are kept close until the connection is complete.

6. After successfully being added, you will have the option to rename the device and assign it to a location. It will now be listed on the app’s home page.  Tap the device listing to enter its control page.
   

Notes:

• The device and the opp have to use the same Wi-Fi network.
• The device is only compatible with 2.4Ghz networks.

REMOTE CONTROL

By default, the remote control will be paired with the ceiling light when taken out of the package. You can also pair and unpair using the Power On button on the remote control.

Pairing with the Ceiling Light

1. Turn off the ceiling light at the wall switch for 10 seconds.
2. Turn on the ceiling light at the wall switch.
3. Within 30 seconds after turning on the light, press and hold the Power On button on the remote until the light flashes 3 times. Your remote is now successfully paired with the ceiling light.

Unpairing the Remote with the Ceiling Light

1. Turn off the ceiling light at the wall switch for 10 seconds.
2. Turn on the ceiling light at the wall switch.
3. Within 30 seconds after turning on the light, press and hold the Power On button on the remote until the light flashes 6 times. Your remote is now unpaired with the ceiling light.

Group Control using the Remote
You may connect multiple ceiling lights to the same wall switch and pair them to the same remote control. There is no limit on the number of ceiling lights that can be controlled by the same remote at the same time.
For group control by the same remote, ensure that all ceiling lights are connected to the same wall switch.
To control/pair the remote with a group of lights:

1. Unpair the remote with each individual ceiling light as instructed in the Unpairing the Remote with the Ceiling Light section.
2. Turn off the group of ceiling lights at the wall switch for 10 seconds.
3. Turn on the ceiling lights at the wall switch.
4. Within 30 seconds after turning on the ceiling lights, press and hold the Power On button on the remote until the lights flash 3 times. Your remote is now successfully paired with all ceiling lights.

GOOGLE HOME CONTROL

Note:
You will need to have set up a Google Home account prior to linking your Kogan Smarter Home” device.

Adding “SmarterHome” to the Google Home app

1. icon to access the ‘Add and manage’ page.
   From the home page of the Google Home app, select the “+”

2. Select ‘Set up device’, then under the Works with Google banner, select ‘Have something already set up?’

3. Select the search bar and type ‘Smarter Home’ to locate the Kogan SmarterHome™ service.
   

4. Tap ‘Authorise’ to grant Google permission to access the SmarterHome™ app and your devices.

5. From here, you will be prompted to sign in to your SmarterHome™ account using either your email or mobile phone number, depending on which method you used to register your account.
   

6. Once connected, the app will display any compatible devices linked to your Smarter Home” account. From here you can assign them to rooms and set up any routines.

7. Tap on any of the devices to view a list of available commands.
   

Note:
Please note that Google Home can only control the base/core functions of any compatible Smarter Home” devices. To make full use of this product’s smart functionality, please use the Kogan Smarter Home” app.

AMAZON ALEXA CONTROL

Note:
You will need to have set up an Alexa account prior to linking your Kogan SmarterHome™ device.

Adding “SmarterHome” to the Alexa app

1. From the home page of the Alexa app, select the – icon in the top-right and select Skills & Games from the sidebar.

2. Select the search bar and type ‘Smarter Home’ to locate the Kogan Smarter Home” skill.
   

3. Tap ‘Enable to Use’ to add the Kogan Smarter Home” skill to Alexa.

4. From here, you will be prompted to sign in to your Smarter Home” account using either your email or mobile phone number, depending on which method you used to register your account.

5. Tap ‘Authorise’ to grant Alexa permission to access the Smarter Home” app and your devices.
   

6. Once connected, the app will perform a search and display the devices linked to your SmarterHome™ account.

7. When your devices have successfully connected to the Alexa app, you will be able to control your Kogan SmarterHome™ devices via Alexa’s voice commands.

Note:
Please note that Alexa can only control the base/core functions of any compatible Smarter Home” devices. To make full use of this product’s smart functionality, please use the Kogan SmarterHome™ app.

SPECIFICATIONS

NOTE

Need more information?
We hope that this user guide has given you the assistance needed for a simple setup.
For the most up-to-date guide for your product, as well as any additional assistance you may require,
head online to help.kogan.com
kogan.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>