LEVITON DRKDN-UXX Wi-Fi Room Controller Instruction Manual

: June 6, 2024
: Leviton

Table of Contents

Description
Pre-Requisites
Installation
**
Configuration and Programming
LIMITED 5 YEAR WARRANTY AND EXCLUSIONS
FCC COMPLIANCE STATEMENT
Customer Support
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

LEVITON DRKDN-UXX Wi-Fi Room Controller Instruction Manual

WARNINGS

TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE WIRING!

CAUTIONS

To be installed and/or used in accordance with appropriate electrical codes and regulations.
If you are unsure about any part of these instructions, consult an electrician.
Use this device with copper or copper clad wire only.
For indoor applications only.
Save these instructions.

Description

The DRC Wi-Fi Room Controller is designed to be used to coordinate and control multiple Intellects'” fixtures and sensors within a room, as well as connected to the system Wi-Fi network for coordination with other GreenMae DRCTM devices. It provides all energy management functionality both as required by code and as desired by the user. All aspects of the system can be configured to meet the specific needs of the end user and their application. An initial configuration can be created without any special tools using only the room controller and installed devices within the room. System refinements can be made using the Leviton GreenMwe’ DRCTM app from your smartphone or other Wi-Fi enabled Android™ or iOS™ device.

DRKDN-U1W
(one button)

DRKDN-U2W
(Two Button) **

**

DRKDN-U4W
(Four button)

DRKDN-U8W
(eight buttons)

Pre-Requisites

NOTE: For connection to Wi-Fi network and smartphone.
NOTE: For connection to Intellect & LuminaRFT” devices.

Requires standard device back box.
May be multi-ganged.
Decora faceplate purchased separately.
Each room requires at least one room controller, other keypads may be used as remote keypads.

Installation

TO AVOID FIRE, SHOCK, OR DEATH; TURN OFF POWER at circuit breaker or fuse and test that power is off before wiring!
Remove 3/4 in. of insulation from each wire lead and connect per diagram. After all connections have been made, ensure that all wire connectors are firmly attached and there is no exposed copper.
Gently place wires and device into wall box and secure with mounting screws.
Install Decora® wall plate. Installation is complete.

NOTE: This device accepts Decora® wall plates (both types – screw less and with screws). If screw plates are used, remove the four tabs at the corners of the mounting strap to avoid interference with the wall plate.

SPECIFICATIONS

Input Voltage/ Frequency| 120-277VAC, 30mA Max, 50/60Hz
Input Current Max| 250mA
Input Current Standby Power| < 0.5W
IP Rating| IP30
Network Connections| Network 1: Wi-Fi – as client to another access point, or, as an access point for direct connection using the Leviton GreenMax® DRCTM app.

Network 2: 2.4”GHz Wireless Mesh for connection to compatible Intellect, LuminaRF, or Zigbee devices

Operating Temperature| 0-40°C
Storage Temperature| -20-85°C

**

NOTE:** Buttons and wall plates can be custom engraved to your specifications. Contact Leviton for availability and order details. To install a color change kit.Color Change and Button Kits

Squeeze the sides of the button frame to release snap tabs and remove.
Install new buttons and wall plate.

Configuration and Programming

System Configuration is performed using the Leviton GreenMax DRCTM app, downloadable from Google Play or the Apple store. The application can be used to:
Initialize device and connect to network
Assign network devices to this controller
Create groups and scenes
Configure daylighting zones and target lighting levels
Define functionality of buttons
Communication to the room controller is over Wi-Fi. Initial configuration and provisioning must be made by a direct connection to the device. The default SSID and credentials are as follows:
Default SSID: GreenMax DRC-xxxx xxxx is the last four numbers of the MAC address, MAC address is labeled on the side of the device.
Default Wi-Fi Password: leviton0000
NOTE: If Wi-Fi has been disabled, push and hold the reset button for 5 seconds to renewable Wi-Fi.
Subsequent to initial provisioning, the access point name will change to the device name as configured by the user, or, the device may be connected to a building access point at which point in time it will be accessible anytime your phone is connected to the building network.
Status/Reset Button. This button can be used to check status and reset. Each function can be activated be pressing the button then releasing after the appropriate time. The LEDs will flash indicating when each threshold has been crossed. See chart below for functionality:

Press and hold

| Action|

Status LEDs

---|---|---
< 1 second| Re-trigger SSID broadcast and report status| 1 Flash – Controller is an Access Point and is pending connection by the app
2 ﬂashes – Controller is an Access Point and has an active connection
3 ﬂashes – Controller is a Wi-Fi Client and is connected to a network
10 ﬂashes – Controller is a Wi-Fi Client and there is a connection error
5 seconds| Enable/Disable Wi-Fi| 2 rapid ﬂashes when triggered (all LEDs)
10 seconds| Reset Wi-Fi network conﬁguration| 3 rapid ﬂashes when triggered (all LEDs)
20 seconds| Reset to factory default| Rapid continuous ﬂashing (all LEDs)

LIMITED 5 YEAR WARRANTY AND EXCLUSIONS

Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for five years from the purchase date. Leviton’s only obligation is to correct such defects by repair or replacement, at its option. For details visit www.leviton.com or call 1-800-824-3005. This warranty excludes and there is disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product is installed improperly or in an improper environment, overloaded, misused, opened, abused, or altered in any manner, or is not used under normal operating conditions or not in accordance with any labels or instructions. There are no other or implied warranties of any kind, including merchantability and fitness for a particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and fitness for a particular purpose, is limited to five years. Leviton is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or profits or delay or failure to perform this warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.

FCC COMPLIANCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Any changes or modifications not expressly approved by Leviton could void the user’s authority to operate this equipment.

FCC SUPPLIER’S DECLARATION OF CONFORMITY:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation. Manufactured by Leviton Manufacturing, Inc., 201 N Service Road, Melville, NY, http://www.leviton.com

Copyright and Trademark

Information Intellect, LuminaRF and DRC are trademarks and GreenMaxis a registered trademark of Leviton Manufacturing Co., Inc. Zigbee is a U.S. registered trademark of Zgbee Alliance. WiFi is a trademark of the Wi-Fl Alliance. Use herein of other third party trademarks, service marks, trade names, brand names and/or product names are for informational purposes only, are/may be the trademarks of their respective owners:i such use is not meant to imply affiliation, sponsorship, or endorsement. No part of this document may be reproduced, transmitted or transcribed without the express written permission of Leviton Manufacturing Co., Inc.

FOR CANADA ONLY
For warranty information and/or product returns, residents of Canada should contact Leviton in writing at Leviton Manufacturing of Canada ULC to the attention of the Q uality Assurance Department, 165 Hymus Blvd, Pointe- Claire (Quebec), Canada H9R 1E9 or by telephone at 1 800 405-5320.