HUMANTECHNIK 25800 Door Monitor System User Manual

Function

A »mona« monitoring system consists of at least one door monitor and a »mona« video receiver. Up to four transmitters can be registered on to one video receiver. When the door monitor‘s bell button is pushed, a radio- and image signal is transmitted to the »mona« video receiver. The receiver indicates the signals through sound and images on its display.

Safety instructions

• Before putting the devices to use, please read this manual completely and thoroughly.
• Keep the manual safety, so that other users have access to it when needed.
• When using power tools, please follow their manufacturer’s instructions and use protective gear (e.g. safety goggles)
• Before drilling into walls, please make sure that no hidden power lines or water pipes are underneath.  If in doubt, we recommend using a cable/pipe detector.

Inserting the power pack into the video receiver

A power pack is included with the video receiver. Slide the battery compartment open and connect the power pack with the socket. Make sure that it is plugged in the right way round! Insert the power pack into the battery compartment, then slide the lid back on.

Setup of video receiver

Insert the cable of the power supply into “DC 6V” socket located on the underside of the charger base. Plug the power supply into a 230 V mains socket. Place the receiver into the charger base. Before initial operation, you should fully charge the receiver for about 15 hours. It is advisable to place the receiver regularly into the charger base in order to charge the power pack and therefore establish interruption-free operation.

Setup of door monitor
There are two possibilities of feeding power to the door monitor: 1st possibility: With six type AA batteries 2nd possibility: The door monitor can be  directly supplied with power via the doorbell wire of your house (+12V DC).

Inserting the batteries into the door monitor

Remove the securing screw and take the battery casing off the back of the door monitor. Insert six batteries (type AA, 1,5 V, alkaline) into the battery compartment. Make sure to match the correct polarity, as incorrect orientation might damage the device! When replacing the batteries, always use good quality alkaline batteries, as  these can last up to two years per battery set (depending on the frequency of use).

Direct power supply on doorbell wire, connection to +12V DC

  We recommend the following installation be done by pro-  fessionals. Do not use the permanent power supply by doorbell wire together with the batteries! This form of power supply is recommended for frequent monitoring functions or when the motion detector is activated.

Remove the battery casing. There are rubber-covered openings in the casing. Carefully cut a hole where you wish to thread the doorbell wire through. Connect the wires according to the illustrations below.

Wiring schematics for door opener function: The trigger has a closing contact (Contact is normally open):

The trigger has an opening contact (Contact is normally closed):

Wall mounting

1. Choose a suitable location for the door monitor. Be sure to consider the average height of visitors.
2. Drill two 6 mm holes in the correct position into the wall. Use the supplied screws and wall plugs and fix the battery casing to the wall.
3. Insert the door monitor.
4. Lock the door monitor into the battery casing with the securing screw.

The door monitor is resistant to splash water and can be mounted outdoors.

Controls and display

Video receiver

Door monitor

Video receiver display

The figures show the regular display which appears when the receiver is activated from standby mode.

A Battery charge status
B Indication during a call
C Battery status of door monitor (when used with batteries)
D Signal strength of monitor
E Zooming
F Rejecting a call
G The plug icon appears when the door monitor is powered by 12 V wire.
H Number of current monitor
I Function definition for left softkey
J Function definition for right softkey

Switching the video receiver on / off

Press and hold until the video receiver switches on. To switch the video receiver off, press and hold again.
Please note that the switched-on receiver will automatically enter standby mode after 20 seconds of the last key entry. Press any key at any time to awaken the receiver from the standby mode.

Registering additional door monitors

The receiver and monitor are already registered together when purchased as a set. The following instructions are for the registration of up to3 additional monitors:

1. Press any key to switch the display on. Press the menu key to enter the main menu. With the navigation keys, select “Register” and press the menu key once more to start the search price dure.

2. Door monitor: Take the battery casing off. Press the call button and use a pointed object (e.g. needle or bent paper clip) to press and hold the register key. See the figure below for the location of the register key.

3. When a single prompt tone is heard, you can release the register button. The registration of the monitor has been successful. If a double prompt tone is heard, the registration has failed. In this case, turn the receiver off. Disconnect the according door monitor from its power source (take batteries out / disconnect from power supply) for 30 seconds. Reconnect the power source. Switch the receiver on and repeat the previous steps.
   Make sure that monitor and receiver are not too far apart.

4. A maximum of 4 monitors can be registered. If an attempt is made to register more than 4 door monitors, the register interface will display “Register full”.

Resetting the registration

All registered monitors can be deleted. To delete the registered monitors, press and hold the Accept key and the right key simultaneously for 5 seconds. The register interface will then display „Register deleted“.

Viewing monitor feeds

If multiple door monitors have been registered, the receiver can toggle between the transmissions of the various door monitors. Press and hold the Monitor key  for 1 second. The video receiver will display a list of the connected monitors. With the Navigation keys ” ” and “ “, select the desired monitor. The images from the selected monitor will be displayed. Please note: This function is only available if the door monitor is connected via the DC+12 V wire feed.

Activating the door monitor motion detector

The door monitor camera can automatically activate and transmit the image when an object moves in front of it. When the automatic snapshot function is activated, 1 – 3 pictures (depending on the selected setting) will be taken. In order to activate the motion sensor, remove the battery casing and switch the selector to “ON”. To deactivate the motion sensor, switch the selector to “OFF”. To automatically save a photo of the detected object,
refer to “Snapshot settings” (Page 29). Video monitor operation

When the call button of the door monitor is pressed, the video receiver rings, and the video image of the visitor appears on the display.

• In order to talk to the visitor, press the Accept key
• To decline, press the End key , this will cancel the ring and video feed.
• To zoom in on the video feed, press and hold the Monitor key

The video conversation will automatically end after 2 minutes. The internal video feed ends automatically after 5 minutes.

Unlock

If the door monitor has been installed accordingly with the electric door lock, press the Unlock key  during the conversation to open the door.

Monitor night vision

The infrared LEDs of the monitors will automatically light the scene when the ambient light becomes too dark. This light is not visible to the person in front of the monitor.

Video receiver: Setting date and time

1.  Press any key to switch the display on. Press the menu key to enter the main menu. With the navigation keys, select “Date & Time”. Press the right key (Select) to enter the selection.
2. The hours cursor blinks. Adjust the hours with the Navigation keys ” ” and ” “. With the right Navigation key ” “, select the minutes and adjust with ” ” und ” “.
3. Press ” ” again to enter the date setting. As described above, use ” ” and ” ” to adjust the date.
4. Press “Save”  to save the settings and return to the previous menu.

The time format is 24 h and the date format is YY-MM-DD. Date and time should be set in order to correctly display the time of captured images.

When replacing batteries or in case of a total discharge of the video receiver’s power pack, date and time must be set again.

Video receiver: Setting the transmission volume

The call volume can be adjusted to 9 levels.

• During a video transmission, press the Navigation keys ” ” and ” ” to adjust the volume.
• If the receiver is in standby mode, press any key to switch the display on. Press the menu key  to enter the main menu. With the navigation keys, select „Volume“, then press “Select” . The volume can be adjusted by pressing “ ” and ” ” Press „Back“ to save the setting and return to the previous menu.

Video receiver: Adjusting display brightness
The display brightness can be adjusted in 9 levels.

• During a video transmission, press the Navigation keys “ ” and ” ” to adjust the brightness.
• If the receiver is in standby mode, press any key to switch the display on. Press the menu key to enter the main menu. With the navigation keys, select “Brightness”, then press “Select” . The volume can be adjusted by pressing “ and “ .
  Press “Back”  to save the setting and return to the previous menu.

Video receiver: Toggle key tone

1. Press any key to switch the display on. Press the menu key to enter the main menu. With the navigation keys, select “Key tone”.Press the left key  (Select) to enter the selection.
2. Use ” ” and ” ” to enable or disable the key tone.
3. Press “Save”   to save the settings and return to the previous menu.

Video receiver: Automatic snapshot settings

The unique snapshot function records photographs of any visitors whether you are present in the house or not. To activate the Auto Snap function, set the receiver up as follows:

1. Press any key to switch the display on. Press the menu key to enter the main menu. With the navigation keys, select “Auto Snap set.”. Press the right key   (Select) to enter the selection.
2. Use “ and “ keys to choose between 1 to 3 photos and “Off” to enable or disable the function.
3. Press „Save“ to save the settings and return to the previous menu.

With Auto Snap-on, the camera in the door monitor will automatically take photographs of your visitors. If you have unreviewed photographs, the backlight of the Replay key will be blinking.
You can save a photograph during a video feed by pressing the Manual Snap / Monitor key  Up to 50 photographs can be stored. When the store is full, the oldest photograph will be overwritten.
Press “Replay” to view the photographs. Use the Navigation keys to browse. If you wish to delete a photograph, select “Delete” according to the image. When prompted “Delete?”, confirm to delete with “Yes” or “No” to cancel the process.

Viewing and deleting photographs

Management of the stored photographs can also be handled via the main menu of the video receiver. In the case of several registered monitors, the number of the monitor is displayed for the according to photograph. In order to view or delete photographs, please follow as below:

1. Press any key to switch the display on. Press the menu key to enter the main menu. With the navigation keys, select “Snap Show”. Press the left key (Select) to enter the selection.
2. Use the Navigation keys “ and “ ” to browse.
3. If you wish to delete a photograph, select “Delete” in the according image. When prompted “Delete?”, confirm to deleting with „Yes“ or „ No“ to cancel the process.

Video receiver: Reset to factory default
In order to reset the video receiver to the factory defaults:

1. Press any key to switch the display on. Press the menu key to enter the main menu. With the navigation keys, select “Default set.”.
   Press the left key  (Select) to enter the selection.

2. Use “ and “ ” to enable or disable the function.

3. Press “Save” to save the setting.

After resetting, the receiver will return to standby mode.
PLEASE NOTE: All custom settings and stored photographs will be lost!

Video receiver: Setting the alert/ringtone tone volume
The volume of the alert tone can be adjusted in 5 levels. Number „0“ is silent and „4“ offers maximum volume.

1. Press any key to switch the display on. Press the menu key to enter the main menu. With the navigation keys, select „Alert volume“.
   This entry can be found on the third page of the main menu.
   Then press „Select“ .

2. The alert tone volume can can be adjusted by pressing “ and “ “.

3. Press „Back“ to save the setting and return to the previous menu.

Video receiver: AUX output
The charger base features an AUX outlet. It is hereby possible to connect a vibrating pad or to establish a connection with the signal systems lisa and signolux.
PLEASE NOTE: In order to use this function, the video receiver must be placed in the charger base!
Vibrating pad (A-3303-0):
Plug the vibrating pad into the AUX outlet.
Connecting a Humantechnik signal system:
With the auxillary cable A-2974-0, a connection to the following transmitters can be established:

• lisa RF doorbell transmitter acoustic (A-2466-0)
• signolux Universal Acoustic Transmitter (A-2656-0, to be connected over the doorbell input socket. Please set the receivers accordingly to display the door-signal)

Maintenance and care

»mona« devices do not require any maintenance. If the units become dirty, simply wipe them clean with a soft, damp cloth. Never use spirits, thinners or other organic solvents. Do not set the units up where they will be exposed to full sunlight for long periods. In addition, they must be protected against excessive heat, moisture and severe mechanical shocks.
Note: These products are not protected against splash water (Except door monitor). Do not place any containers filled with water, such as flower vases, or anything with an open flame, such as a lit candle, on or near the products.
Please make sure that the batteries are not exposed to excessive heat from such as sunlight, fire or anything similar.

Warranty

The »mona« devices are very reliable products. Should a malfunction occur despite the units having been set up and operated correctly, please contact your dealer or the manufacturer directly. This warranty covers the repair of the products and returning them to you free of charge. It is recommended that you send in the product in its original packaging, so keep the packaging for the duration of the warranty period.
The warranty does not apply to damage caused by incorrect handling or attempts to repair the unit by people not authorised to do so (destruction of the seal on the unit). Repairs will only be carried out under warranty if the completed warranty card is returned accompanied by a copy of the dealer‘s invoice/till receipt.
Always specify the product serial number in any event.

Disposal of used electric and electronic units (applicable in the countries of the European Union and other European countries with a separate collection system). The symbol on the product or the packaging indicates that this product is not to be handled as ordinary household waste but has to be returned to a collecting point for the recycling of electric and electronic units.
You protect the environment and health of your fellow men by the correct disposal of this products.
Environment and health are endangered by a faulty disposal.
Material recycling helps to reduce the consumption of raw material.
You will receive further information on the recycling of this product from your local community, your communal disposal company or your local dealer.

Technical specification Door monitor:

Technical specification Video receiver:

These devices comply to the following EC standards:

– 2011 / 65 / EC RoHS-Directive
– 2012 / 19 / EC WEEE-Directive
– 2014 / 53 / EC RED-Directive
Compliance with the directives listed above is confirmed by the CE seal on the device. CE compliance declarations are available on the Internet at www.humantechnik.com within the „service“ section.
Technical specifications subject to change without prior notice.

Humantechnik Service-Partner

Great Britain

Sarabec Ltd
15 High Force Road
GB-Middlesbrough TS2 1RH| Tel.: +44 (0) 16 42/ 24 77 89
Fax: +44 (0) 16 42/ 23 08 27
E-mail:enquiries@sarabec.co.uk
---|---

For other service-partners in Europe please contact:

Humantechnik Germany
Tel.: +49 (0) 76 21/ 9 56 89-0
Fax.: +49 (0) 76 21/ 9 56 89-70
Internet: www.humantechnik.com
E-mail: info@humantechnik.com
RM2580-0 – 2020-12

Documents / Resources

| HUMANTECHNIK 25800 Door Monitor System [pdf] User Manual
25800 Door Monitor System, 25800, Door Monitor System
---|---

References

• Willkommen
• Service

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>