dormakaba RCI 912-WBT Series Wireless Battery Powered Touchless Switch Installation Guide

: June 6, 2024
: dormakaba

Table of Contents

OVERVIEW
SENSING DISTANCE ADJUSTMENT
RECEIVER I/O DIAGRAM
PAIRING & RESET
- Transmitter/Receiver Pairing:
REGULATORY STATEMENTS
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

dormakaba RCI 912-WBT Series Wireless Battery Powered Touchless Switch

OVERVIEW

Infrared motion detection technology
Non-contact activation with hands or reflective objects is clean and hygenic
The detection distance is adjustable from 1-12″ (3-30cm)
High sensitivity infrared, quick response
2.4GHz wireless transmission adopts wireless transmitter/receiver
Low power consumption sensor provides long battery life
Receiver 3 Amp @ 30 VDC output can be used with automatic door and access control
After receiving the signal, the door opening signal is output for 1.5 seconds
Receiver voltage input 12~30 VDC

SPECIFICATION| 912-WBT, 912-WBT-HC| 912N-WBT, 912N-WBT-HC| 912GL-WBT, 912GL-WBT-HC
---|---|---|---
Power Input| 6 VDC (4 AA batteries)| 3 VDC (2 AA batteries)| 3 VDC (2 AAA batteries)
Static Current| ≤ 80uA| ≤ 80uA| ≤ 80uA
Battery Life| 500 actuations/day ~ 450 Days| 200 actuations/day ~ 250 days| 200 actuations/day ~ 220 Days
Emmission Current| 10mA| 10mA| 10mA
Infrared Modulation Frequency| 38KHz| 38KHz| 38KHz
Infrared Scanning Interval| 100ms| 100ms| 100ms
Response time| ≤ 130ms| ≤ 130ms| ≤ 130ms
Transmitter Range| >30M (100′) in clear line of sight| >30M (100′) in clear line of sight| >30M (100′) in clear line of sight
**Working Temperature*| -42˚C ~ 45˚C (-43˚F ~ 113˚F)| -42˚C ~ 45˚C (-43˚F ~ 113˚F)| -42˚C ~ 45˚C (-43˚F ~ 113˚F)
Working Humidity| 10 ~ 90% RH| 10 ~ 90% RH| 10 ~ 90% RH
Size| 129mm L x 129mm W x 46mm H (5.0″w L x 5.0″ W x 1.8″ H)| 121mm L x 51mm W x 46mm H (4.8″ L x 2.0″ W x 1.8″ H)| 86mm L x 86mm W x 15mm H (3.4″ L x 3.4″ W x 0.6″ H)
Certifications**| FCC, ISED FCC, ISED| FCC, ISED

SENSING DISTANCE ADJUSTMENT

| The clockwise direction will increase sensing distance.
The counterclockwise direction will decrease sensing distance.
---|---
SPECIFICATION RECEIVER model 912-R

RECEIVER I/O DIAGRAM

PAIRING & RESET

Transmitter/Receiver Pairing:

Press Learn Button for 1 second. LED will change from green to red, indicating learn mode.
Activate Transmitter Button Red, Blue. LED will flash alternately, indicating units are paired.
Select momentary or latching for activation action.

Note: Follow steps 1 & 2 for additional units.

Reset receiver:

Press and hold Learn Button for 5 seconds.
Will delete memory

Note: As this device uses wireless transmitter and receiver technology, location of these devices is critical to optimal operation. Locating the receiver in close proximity to other electrical devices and connections may cause erratic behavior.
Should this happen, relocate the receiver.

REGULATORY STATEMENTS

FCC statement:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help

ISED statement:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.

Documents / Resources

| dormakaba RCI 912-WBT Series Wireless Battery Powered Touchless Switch [pdf] Installation Guide
RB506, 2AED9-RB506, 2AED9RB506, RCI 912-WBT Series Wireless Battery Powered Touchless Switch, RCI 912-WBT Series, Wireless Battery Powered Touchless Switch
---|---