REDRAGON Ashe Pro 3 Modes 78 Key Mechanical Gaming Keyboard Instruction Manual

REDRAGON Ashe Pro 3 Modes 78 Key Mechanical Gaming Keyboard

Dear user
Thank you for choosing product. To protect your rights and for better customer service, please read the following warranty rules carefully.

How to connect the keyboard with a computer Wired Connection

1.  Slide the 2.4G/OFF/BT switch on bottom of keyboard to OFF.
2.  Take out the USB A to USB Type C cable in the package and connect the keyboard with your computer.
3.  The computer will recognize and configure the keyboard automatically.
4.  The keyboard will be ready for use when the configuration is finished.
5.  Once the keyboard is powered up, charging begins. The LED marked with M light s flash in green then tun to red . It will turn to red when keyboard is fully recharged.

2.4G Wireless Connection

1.  Slide the 2.4G/OFF/BT switch on bottom of keyboard to 2.4G.
2.  Take out the nano USB receiver and plug it into an available USB port on your computer. The computer will recognize and configure the keyboard automatically.
3.  The keyboard will be ready for use when the configuration is finished.
4.  In some cases, you may need to pair the keyboard. Turn on the keyboard and press [FN]+[2.4G] for about 3 seconds, the LED marked with M flashes in yellow, plug the USB receiver into any available USB port on your computer within 20 seconds. The keyboard will be paired automatically. Make sure the keyboard has enough power before doing so.
5.  The indicator will flash when the battery is low. Please recharge the keyboard in time or it will turn off automatically soon.

Bluetooth Connection

1. Slide the 2.4G/OFF/BT switch on bottom of keyboard to BT.
2. Press [FN]+[BTl ](or [BT2]/[BT3] for other Bluetooth devices), the LED marked with M flashes in blue {or cyan/magenta for the others)
3. Turn on Bluetooth and scan for available devices on your computer or smart phone. It will find “BT3.0KB or BTS.0 KB” device. Select it and it will connect automatically.

Function Introduction

1.  With standard USB and 2.4G/BT connections, the keyboard can be used on computers without any software or driver installation.
2.  There are 20 backlight effects: FN+”\l”key(marked Mon the key)
3.  Commands of key combinations with [FN] key
4. [FN+ESC]:’ ~
11. FN+7]:F7
15. [FN+”-_”]:Fl 1
16. [FN+”=+’1:F12
17. [FN] + [Win]: Disable or enable the [Win] key.
18. [FN] + [Q]: Select Bluetooth device one (for Bluetooth connection).
19. [FN] + [W]: Select Bluetooth device two (for Bluetooth connection).
20. [FN] + [E]: Select Bluetooth device three (for Bluetooth connection).
21. [FN] + [R]: Change to 2.4G wireless connection. Press and hold the [FN]+[4] for 3
22. FN+P=PRTSC
23. FN+U=SCRLK
24. FN+])=PAUSE
25. FN+L=INS
26. FN+;:=HOME
27. FN+”‘=END
28. FN+,<=DEL
29. FN+.>=PGUP
30. FN+/?=PGDN
31. FN+L_CTRL=APP
32. FN+ R_ALT : Switch in 12 backlighting patterns
33. FN + TAB: Set the keyboard to default setting.
34. FN+SPACE: Change backlight color.
35. FN+ t / t : Decrease/increase the backlight brightness,total 5 levels. FN+ /——‘>: Change light running speed, total 5 levels.
36. FN+Capslk: All key in white color by one click
37. FN+Backspace:Turn ON/OFF the backlight

How to charge keyboard

Find the USB A to USB type C cable in the packaging ,plug the keyboard and connect it with computer for charging, the LED indicator of keyboard will be turn to red. Remark: The LED indicator will be turn to red when keyboard is out of battery.

Indicators on keyboard up of left

“A”is for Captals lock indication nM” is for connection mode indication

FAQ

1.  If the keyboard doesn’t respond, please check if the keyboards USB cable is correctly inserted into the corresponding USB port on the computer, or try another USB port on the computer.
2.  If you spill liquid on the keyboard, please unplug the keyboards USB cable from the computer immediately. Wipe off excess liquid and put the keyboard in a dry and ventilated place. Make sure the keyboard is dried naturally before the next use

FCC Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1 )this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>