HYUNDAI WSC 2208 WEATHER STATION Instruction Manual

June 5, 2024
HYUNDAI

HYUNDAI-LOGOHYUNDAI WSC 2208 WEATHER STATION

FEATURES

Weather Forecast
  • Two Weather Icon
  • Sunny, Slightly Cloudy, Cloudy, Rainy and Snow animation
Humidity
  • Indoor & Outdoor measurable range: 20 ~ 99 %
  • Outdoor Humidity Record from Start-Up / Reset, and the corresponded time
  • 24 Hours Min/Max Display for Outdoor Humidity
Time
  1. Radio Controlled Time with Manual Setting Option
  2. 12/24 hour time display selectable
  3. Daily Snooze Alarm function
  4. Perpetual Calendar Up to Year 2069
  5. Day of week in 5 languages user selectable
Temperature
  • Indoor measurable range: −5 °C ~ +50 °C
  • Measures °C / °F user selectable
Wireless Outdoor Sensor
  • Low-battery indicator for Outdoor Thermo Sensor
  • Wall Mount or Table Stand
  • One Wireless Thermo Sensor Included
  • 433 MHz RF transmitting frequency
  • 30 meter transmission range in an open area

MAIN UNIT APPEARANCE

HYUNDAI WSC 2208 WEATHER
STATION-1

Part A – LCD
  1. Time
  2. Date
  3. Day Of Week
Part B – Buttons
  1. “MODE” Button
  2. “SNOOZE / LIGHT” Button
  3. “ALARM” Button
Structure
  1. Battery Compartment
  2. Temperature
  3. Radio Controlled Icon
  4.  “▼/ C / F” Button
  5.  “RESET” Button
  6. “▲/ 12 / 24” Button

OUTDOOR THERMO SENSOR

HYUNDAI WSC 2208 WEATHER
STATION-2

  • Transmission Indication LED
  • Outdoor Temperature display
  • Outdoor Humidity display
  • Battery Compartment
  • Wall Mount Hole
  • “RESET” button
  • “C/F” button
  • Temperature Probe Plug & Jack D9: Stand

GETTING STARTED:

Main Unit:
  • Open main unit battery compartment cover [C2]
  • Insert 3 x AAA batteries observing polarity [“+” and “−” marks]
  • Replace main unit battery compartment cover [C2]
  • Use a pin to press the RESET [B1] button on the rear of the main unit, the main unit is now ready for use
Outdoor Thermo Sensor
  • Batteries compartment (D4) of thermo sensor is locating behind the back cover,
  • Insert 2 x AAA batteries observing polarity [“+” and “−” marks]

INSTALLATION

Main Unit
The main unit can be placed onto any flat surface (C3), or wall mounted by the hanging hole (C1) at the back of the unit.
Outdoor Thermo sensor
The remote sensor should be securely mounted onto a horizontal surface.
Note: Transmissions between receiver and transmitter can reach up to 30 m in open area. Open Area: there are no interfering obstacles such as buildings, trees, vehicles, high voltage lines, etc

WEATHER FORECAST FUNCTION

Operation
  • After Batteries inserted, or holding “WEATHER” button (B8) for 3 seconds, weather icon flash (A5) on the LCD. Enter the current weather by pressing “−” (B5) or “+” (B4) button. Press
    “WEATHER” (B8) button to confirm the setting. The weather forecast may not be accurate if the current weather entered is not correct.

  • There are two weather icons, the left one indicate current weather condition, the right one forecasts the weather in terms of getting better or worse. The weather station will start the first forecast at 6 hours later after the current weather status is entered.

  • The current weather status should be entered again if the altitude of the Main Unit is changed.(Barometric pressure is lower at higher altitude location. Therefore, altitude change will affect the weather forecast).

Weather Conditions
There are totally 5 different weather status animations in the weather forecast.HYUNDAI WSC 2208 WEATHER STATION-3 Note:

  • “Freezing or snow” is shown if the weather forecast is Rainy and outdoor temperature (any channel) is under 0 °C.
  • Frost Alert: “ ” is shown if the outdoor temperature (any channel) is between − 2 °C ~ +3 °C.
  • If there is any inconsistency of weather forecast between Local Weather Station and this unit, the Local Weather Station’s forecast should prevail. The manufacturer will not hold responsible for any trouble that may come up due to wrong forecasting from this unit.

THERMOMETER

RF Transmission Procedure:
  • The main unit automatically starts receiving transmission from outdoor thermo sensor for outdoor temperature & humidity after weather condition setting.
  • The outdoor sensor will automatically transmit temperature and humidity signal to the main unit after batteries inserted.
  • If main unit failed to receive transmission from outdoor thermo sensor in first 3 minutes after the batteries inserted (“- – . –” display on the LCD), hold “SEARCH” button (B9) for 3 seconds to receive transmission manually. RF icon “ ”.
Temperature & Humidity

Past 24 Hours Maximum / Minimum Outdoor Temperature and Humidity

  • After start up, the unit automatically shows past 24 hours maximum outdoor temperature and humidity record. “MAX” show on the LCD
  • After start up, the unit automatically shows past 24 hours minimum outdoor temperature and humidity record. “MIN” show on the LCD.

Recorded Maximum/Minimum Outdoor Temperature and Humidity from Start-up / Reset

  • Press “MEM” button (B3) to view the maximum and minimum temperature and humidity record from start-up or reset. “ ” flash on the LCD.
  • When viewing the memory record, hold “MEM” button for 3 seconds to clear the maximum and minimum record.
  • When viewing the memory record, press “MEM” button (B3) again to check the corresponded time and date for memory maximum and minimum temperature & humidity record. The memory record value and corresponded time and date flash. Press “MEM” button select to view:
  • Time & date for minimum temperature memory record, Time & date for minimum humidity memory record, Time and date for maximum temperature memory record, Time and date for maximum humidity memory record.

Celsius / Fahrenheit

  • Press “°C / °F” button (B5) to select Indoor / Outdoor Temperature in Celsius mode or Fahrenheit mode.
  • If the temperature is out of the measurable range, LL.L (beyond the minimum temperature) or HH.H (beyond the maximum temperature) will be shown on the LCD.

Humidity

  • The humidity measurable range is 20 % ~ 99 %. If the current humidity measurement is lower than 20 %, the LCD would display .
  • For past 24 hours or memory maximum or minimum temperature and humidity record.
    If the record is lower than 20 %, the LCD would display .

Outdoor Temperature Alert Function

  • Press “ALERT” button (B7) to select to activate or deactivate outdoor temperature alert function.

  • Press ALERT button select to:
    Active outdoor upper temperature alert, the icon “ ” besides outdoor temperature digit would display.
    Active outdoor upper& lower temperature alert, the icon “ ” besides outdoor temperature digit would display.
    Active outdoor lower temperature alert, the icon “ “ besides outdoor temperature digit would display.
    Deactivate outdoor temperature alert, alert icon disappear.

  • Hold “ALERT” button (B7) for 3 seconds to enter outdoor temperature alert setting. Icon “ ” or “ ” beside Temperature’s digits flash. Press “+” or “−” button to adjust the setting value, press “MODE” (B2) to confirm the setting. Setting Sequence as follow:
    Upper limit of temperature, Lower limit of Temperature.

  • When it’s alert, the corresponding icon “ ” or “ ” and temperature digit would flash on the LCD. Press any buttons to stop the alert sound, otherwise, it will sound for 2 minutes, and stop automatically.

Comfort Indicator Bar

  • (A6) for the display of pleasant / unpleasant climate.

The use of 1.5 m cord Temperature Probe:

  • Insert the probe plug (D8) to the jack on the right hand side of the Thermo Sensor Unit.
  • Put the cable outside and leave the Thermo Sensor Unit indoor to avoid freezing up the battery when the outdoor temperature is below −20 °C.
  • Always use the temperature probe to sense the temperature when the temperature is between the following range: −50 °C ~ 0 °C and +50 °C ~ +70 °C

TIME AND ALARM SETTING

Radio Controlled Clock
  • 1After the start-up of the unit, the clock automatically starts to scan the DCF time signal. Radio Control Icon (A5) flashes on LCD
     (A2) flashes,

Indicating now is receiving DCF signal

| (A2) turns on,

Indicating signal received successfully

| (A2) disappear,

Indicating signal reception failed

---|---|---

  • The clock is automatically synchronized with the DCF radio signal every day at 3.00 a.m. to maintain accurate time keeping. If synchronization with the DCF radio signal fails, “ ” on LCD disappear and the clock then attempts to synchronize with the DCF radio signal at 4.00 am, 5.00 am and 6.00 am.
  • The clock can be set to scan the radio signal manually by holding “▲” button (B6) & “▼” button (B4) for 3 seconds. Each reception takes several minutes. If receptions fail, scanning stops (“ ” on LCD disappear) and repeats again on next full hour. E.g. scanning failed at 8.20 a.m. It will scan again at 9.00 a.m.
  • Stop scanning DCF radio signal manually by holding “▲” button (B6) & “▼” button (B4) for 3 seconds.
  • “DST” shown on the LCD if it is in Daylight Saving Time Mode.

Note: Button will not function while scanning for DCF radio signal unless they are well received or stopped manually.

Manual Time Setting
  • In time display mode, hold “MODE” button (B1) for 3 seconds to enter Clock / Calendar setting Mode.
  • Press “▲” (B6) or “▼” (B4) button to adjust the setting and press “MODE” button (B1) to confirm each setting.
  • (By keeping the “▲” (B6) or “▼” (B4) button pressed, could accelerate the process and reach the desired value more quickly.)
  • The setting sequence is shown as follow: Hour, Minute, Second, Year, Month-Date Sequence, Month, Date, Time Zone and Language of Weekday.
  • There are 5 languages for day of week: German, English, Dutch, Poland and Czech.
  • The languages and their selected abbreviations for each day of the week are shown in the following table.
    Language| Sunday| Monday| Tuesday| wednesday| Thursday| Friday| Saturday
    ---|---|---|---|---|---|---|---
    German, GER| SON| MON| DIE| MIT| DON| FRE| SAM
    English, ENG| SUN| MON| TUE| WED| THU| FRI| SAT
    Poland, PL| NIE| PON| WTO| SRO| CZW| PIA| SOB
    Czech, CZ| NED| PON| UTE| STR| CTV| PAT| SOB
    Dutch, NET| ZON| MAA| DIN| WOE| DON| VRI| ZAT

Note:

  • All Setting mode will automatically exit in 15 seconds without any adjustment.
  • For Time Zone: The Time zone is used for the countries that can receive the DCF time signal but the time zone is different from German time. When the country time is faster than the German time for 1 hour, the zone should be set to +1. Then the clock will automatically set 1 hour faster from the signal time received. If you receive no RC-DCF frequency signal, the time zone should be set to 0.
Daily Alarm Setting
  • Press the “ MODE” button (B1) to select to view
    Time Alarm Time („AL“ shown on the display)

  • When viewing the Alarm Time, hold the “MODE” button (B1) for 3 seconds to enter Alarm Time setting. Press “▲” (B6) or “▼” (B4) button to adjust the alarm time. Press “MODE” button (B1) to confirm the setting.

Snooze Alarm Function
  • Press the “ALARM” button (B3) to activate the alarm function. “ ” appears on the display.
  • When alarm alerts, press any button to stop the alarm. Otherwise, the alarm signal sounds for about 2 minutes, then stops automatically.
  • Press “SNOOZE / LIGHT “(B2) to activate the snooze function. “ ” appears on the display.
  • Press the “SNOOZE / LIGHT” (B2) button when alarm alerts. The alarm snoozes for around 4 minutes, then it alerts again. The snooze function can be enabled for maximum 8 times. “ ” flashes on the LCD during the snooze time.
  • Except “SNOOZE” button, press any button to stop the snooze alarm, or press the “ALARM” button (B2) to deactivate snooze alarm function. disappear from the display.
12/24 Hour Display mode

Press the  “12/24” button (B11) to select 12 or 24 hours mode.

THERMOMETER

  • Press the “°C / °F” (B4) button to select Temperature in Celsius mode / Fahrenheit mode.
  • If the temperature is out of the measurable range, LL.L (beyond the minimum temperature) or HH.H (beyond the maximum temperature) will be shown on the LCD.

BACKLIGHT

Press the “SNOOZE / LIGHT” button (B2), backlight states for 5 seconds.

PRECAUTIONS

  • The clock loses its time information when the battery is removed.
  • Do not expose it to direct sunlight, heavy heat, cold, high humidity or wet areas
  • Never clean the device using abrasive or corrosive materials or products. Abrasive cleaning agents may scratch plastic parts and corrode electronic circuits.

we reserve the right to change technical specifications.
WARNING:
Do not use this product near water, in wet areas to avoid fire or injury of electric current. Always turn off the product when you don’t use it or before a revision. There aren’t any parts in this appliance that are reparable by consumers. Always appeal to a qualified authorized service. The product is under dangerous tension. Old electrical appliances, used batteries and accumulators disposal This symbol appearing on the product, on the product accessories or on the product packing means that the product must not be disposed of as household waste. When the product/ battery durability is over, please, deliver the product or battery (if it is enclosed) to the respective collection point, where the electrical appliances or batteries will be recycled. The places, where the used electrical appliances are collected, exist in the European Union and in other European countries as well. By proper disposal of the product, you can prevent possible negative impacts on the environment and human health, which might otherwise occur as a consequence of improper manipulation with the product or battery/ accumulator. Recycling of materials contributes to the protection of natural resources. Therefore, please, do not throw the old electrical appliances and batteries/ accumulators in the household waste. Information, where it is possible to leave the old electrical appliances for free, is provided at your local authority, at the store where you have bought the product. Information, on where you can leave the batteries and accumulators for free, is provided to you at the store, at your local authority.

CE DECLARATION OF CONFORMITY

The manufacturer (authorised representative): ETA a. s., Zelený prune 95/97, 147 00 Praha 4 – Braník, IČO: 275 44 001, declares that the following product: Weather Station
type – designation: wS 1166, is in compliance with requirements and other relevant provisions of the R&TTE Directive 1999/5/EC regarding on Radio Equipment and Telecommunications Terminal equipment, and is in compliance with RoHS Directive 2011/65/EU on the restriction of the use of certain hazardous substances in electrical and electronic equipment For the conformity assessment the following technical regulations were used:
European harmonized standards

ETSI EN 301 489-3 V1.6.1 (2013-08) ETSI EN 301 489-1 V1.9.2 (2011-09) ETSI EN 300 330-1 V1.7.1 (2010-02) ETSI EN 300 330-2 V1.5.1 (2010-02) EN 60950-1:2006+A11:2009+A1:2010+A12:2011
EN 62479:2010
The test results are introduced in Test reports No. GTSE14060109401, GTSE14060109402, GTSE14060109403 and GTSS14060109403, which were issued by the laboratory
GTSE-Global Limited Technology Sevices Co., Ltd., P. R. China and Declaration of RoHS
(BOM List) issued by the manufacturer with references to the Test Reports RoHS.
We declare that the product fulfills the essential requirements of the abovementioned Directives, thus safety and health of the user, electromagnetic compatibility and efficient use of spectrum.
The device is used to receive a radio time signals at a frequency of 77,5 kHz in the Czech Republic and EU countries.
Declaration issuance date and venue: 12 July 2014, Prague

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals