OPTONICA 6345 Touch Wheel RF Remote Controller User Guide
- June 6, 2024
- OPTONICA
Table of Contents
OPTONICA 6345 Touch Wheel RF Remote Controller
Feature
- Apply to a single color, dual color, RGB, RGBW or RGB+CCT LED controller dimming driver or smart tamp.
- Ultra sensitive color adjustment touch wheel.
- Adopt 2.4GHz wireless technology, remote distance up to 30m.
- Each remote can match one or more receivers.
- Battery-powered (2 x AAA)
- Operate with LED indicator light.
Technical parameter
- Output signal: RF(2.4GHz)
- Working voltage: 3VDC(AAA*2pcs)
- Working current: < SmA
- Standby current: < 1 OµA
- Standby time: 2 years
- Remote distance: 30m
- Working temperature:-30″C~55″C
- Dimension: L 122 W53 H17.5mm
- Weight:60g
Dimension
Operation
-
When turning on the light, the indicator displays blue. when turn off the light, the indicator display red.
-
When touching the color wheel, the indicator will display the same color:
-
When the press or touch operation is invalid (If the light is off), the indicator display red.
-
To extend battery life, no touch or press key operation after a few seconds, the touch wheel will enter sleep state, you need to press any key to make the touch wheel quit sleep state. Match guide Remote match with 2.4G RF controller, dimming driver or smart lamp. there are two kinds of methods to match receivers.
-
Use Match key Match with controller(with match key)
- Match: Short press the match key, then press the on/off key or zone key of the remote within 5s.
- Delete: Long press match key for 5s, delete all matched remote.
- Multiple zones remote only uses a zone key to match each zone receiver.
-
Use Power-up
Match with controller(without match key), dimming driver or smart lamp- Match: Switch off the power, then switch on power again, short press on/off key or zone key 3 times on the remote quickly within 5s after power on, the link is done once the light blinks 3 times.
- Delete: Switch off the power, then switch on power again, short press on/off key or zone key 5 times on the remote quickly within 5s after power on, the unlink is done once the light blinks 5 times.
- Multiple zones remote only uses a zone key to match each zone receiver.
4 zone RGB/RGBW remote
- Short press turn on/off all zone light
- Touch to change the current zone static RGB color.
- Short press select and turn on zone light, long press 2s turn off zone light. Short press the multiple zone key fastly, will select multiple zones synchronously.
- Short press get red, green or blue color directly. long press 1-5s adjust R/G/B brightness continuously.
- For RGB light, the short press turns on/off white(RGB mix), long press 1-5s adjusts saturation continuously, namely changing the current static RGB color to mixed white slowly. For RGBW light, the short press turns on/off the W channel, long press 1-5s adjust W brightness continuously, namely change saturation by adding white color slowly.
- Adjust dynamic mode for the currently selected zone, Short press run next dynamic mode, long press 2s run mode-cycle
- For static color, adjust brightness, short press 10 levels, long press 1-5s for continuous 256 levels adjustment. For dynamic mode, adjust speed, short press 1 0 levels, long press 2s get the default speed.
- Short press recall the scene, long press 2s save current state into S1/S2. 4 zone recall or save synchronously.
Safety information
-
Read all instructions carefully before you begin this installation.
-
When installing the battery, pay attention to the battery’s positive and negative polarity. A long time without the remote control, remove the battery.
When remote distance becomes smaller and insensitive, replace the battery. -
If no response from the receiver, please re-match the remote.
-
Gently handle the remote, beware of falling
-
For indoor and dry location use only.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>