OPTONICA IP20 Power Supply User Manual
- June 3, 2024
- OPTONICA
Table of Contents
User manual
IP20 Power Supply
For your safety, install according to the instructions!
INSTRUCTIONS FOR USER
TECHNICAL SPECIFICATIONS:
Product: Non-waterproof electronic power supply for LED strip
Input voltage: 100-240V/50-60Hz (PRI)
Output voltage· 12V DC (SEC)
Level of protection: IP 20 (indoor use only)
Electrical protection class. Class I
Ambient temperature: -25°C – +40°C
INSTALLATION:
For proper installation follow installation chart shown schema.
Connect cables properly on terminal contacts according to given figure.
IMPORTANT WARNING:
Please read the instructions carefully before installation and preserve it
well Recommend, the lamp must be installed and assembled by qualified
electrician The mains supply should be turned off before installation. Do not
turn the lamp on before the end off installation.
Please use proper wire for connection. The installation of power supply into
circuits with large inductive loads or voltage surges should be avoided. The
output leads should be kept separate and apart from input leads. The lenght of
output leads should be typically 0.5m–2m in order to keep radio interference
minimum. Always ensure that the correct type of LED strip is used and that the
maximum rating is not exceeded. The label power of LED strip must match the
output power of power supply Power supply is for indoor use only It is not
intended that this product is used by children, persons with reduced physical,
sensory or mental capabilities.
NOTE
Wireless controller for RGB must be installed on output power supply at 12V DC for LED products.
PROTECTION FROM BURNS AND FIRE
** Do not operate the LED strip if the ambient temperature (Ta) exceeds
45°C (113° C). Do not modify the LED strip in any way not described in this
manual or instal than genuine Mitea Lighting parts. Use only accessories
approved by Mitea Lighting.
If any of the product**
temperature readouts exceed the level, provide fan assistance to give active
cooling to the installation.
| Symptoms | Possible Causes | Solutions |
|---|---|---|
| None of the LEDs light up | 1.No power to the driver. | Please check to see if |
there is power being delivered to the drivers power supply via the connection
to AC power.
2.The power supply driver connection is wired incorrectly.| Check the polarity
for 12V connections, positive (+) to positive and negative (-) to negative.
See power supply driver wiring diagram (Section Cl).
3.There is no output voltage from the power supply driver.| Check the power
supply driver; it may need to be replaced.
4.The strip wires are not connected properly to the strip or to the driver.|
Check the connectors and polarity.
Make sure strip is cut correctly and strip terminals are making a connection
within the connector.
5.Overvoltage may have damaged the LEDs.| The working voltage should be within
5% of the rated voltage (12V). If overvoltage has damaged the product then
this is not covered by the warranty.
Some of the LEDs do not work| 1.LEDs on the strip are powered in series. If
some LEDs in the centre of the strip do not light and LEDs towards the end of
the strip do light then the LEDs have failed.| Strip may need to be replaced.
2.If the LEDs in the beginning of the strip work but none are working after
the first non-working LED then there is a connection issue. This could be
caused by a poor connection or if the connector is not fitted to the strip
correctly.
This could also be a result of the strip being bent more than the recommended
bending diameter.| Please check the strip connection from the section of the
strip that is not lit. Check soldering connections. Check connector joins.
Strip may need to be replaced.
The strip when lit is dim or not
evenly lit| 1. The power load (total Wattage of all strips connected) exceeds
the rated Wattage of the power supply driver (total output).| The power supply
needed will depend on the total length of strips in use.The power supply
driver will need to have an output that is at least 10% more than the total
wattage needed to power the strip. See section A.
2. The length of wire between the strip and power supply or the length of the
wire in between each strip is too long.| 1.Use shorter strip supply wires.
2.Use thicker supply wires.
3.Make sure that the input voltage of each LED strip is within 90% of the
rated voltage.
3. Too many LED strips are connected to the power supply driver.| 2. Make
sure that the total wattage of all LED strips is within 90% of the total
output of the power supply driver. If the total wattage of all strips exceeds
the driver output then please use a higher wattage driver.
All LEDs are flashing
intermittently| There is an intermittent connection at the power supply
driver.| Please check driver to AC connection and driver to strip connection.
Some of the LEDs are flashing
intermittently| There is an intermittent connection at each strip branch
connection.| Please check all strip connections and check connector joins.
LEDs blink once when power is switch on| Please check that the driver is
compatible.| This is a 12V constant voltage LED strip. You will need to power
the strip using a 12V constant voltage LED driver.
Always switch OFF power before adjusting the wiring or strip.
Information about protection of environment
This product can’t be disposed on the end of-service with garbage from
household, but should be postponed in a place for recycling electrical and
electronic equipment. The alert is on the markings on the product itself,
user’s manual and box.
No part of the specification may be reproduced in any means or used to make
any changes such as translation, transformation or adaptation without
permission from Trgovina Matejic d.o.o.. All rights reserved.
The manufacturer / distributor takes no responsibility for damage or injury
resulting from improper installation or improper use.
IMPORTER: Prima Group 2004 LTD, Bulgaria, 1784 Sofia, Mladost 1, bl. 144,
Ground Floor; Phone: +359 2 988 45 72;
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>