BANNER R90C 4-Port Discrete Bimodal to IO-Link Hub User Guide
- June 6, 2024
- BANNER
Table of Contents
R90C 4-Port Discrete Bimodal to IO-Link Hub
Quick Start Guide
This guide is designed to help you set up and install the R90C 4-Port Discrete Bimodal to IO-Link Hub. For complete information on programming, performance, troubleshooting, dimensions, and accessories, please refer to the Instruction Manual at www.bannerengineering.com. Search for p/n 221279 to view the Instruction Manual. The use of this document assumes familiarity with pertinent industry standards and practices.
- Compact bimodal to IO-Link device converter that connects discrete inputs and sends the value to the IO-Link Master
- Enabled Delay Modes: ON/OFF Delay, ON/OFF/Retriggerable One-shot, ON/OFF Pulse-stretcher and Totalizer
- Measurement Metrics: Count, Events Per Minute (EPM), and Duration
- Discrete Mirroring: Discrete signals (In/Out) from all four ports can be mirrored to any of the four ports, Discrete Out, or the host white wire output
- Outputs a discrete value as received from IO-Link Master Process Data Out
- Discrete Input/output can be independently configured as NPN or PNP
- Rugged over-molded design meets IP65, IP67, and IP68
- Connects directly to a sensor or anywhere in-line for ease of use
- R90C IO-Link hubs are a quick, easy, and economical way to integrate non-IO-Link devices into an IO-Link system
Overview
The R90C-4B21-KQ hub connects two discrete channels to each of the four unique
ports, providing access to monitoring and configuring those
ports with an IO-Link master. Host mirroring is available where a selected
port input/output discrete signal can be routed to Pin 2 (male) on the
PLC/Host connection.
IO-Link®
IO-Link® is a point-to-point communication link between a master device and a
sensor and/or light. It can be used to automatically parameterize
sensors or lights and to transmit process data. For the latest IO-Link
protocol and specifications, please visit www.io-link.com.
For the latest IODD files, please refer to the Banner Engineering Corp website
at: www.bannerengineering.com.
Resources
For more information, see P/N 221282 R90C-4B21-KQ IO-Link Data Reference Guide and P/N 221283 R90C-4B21-KQ IODD Files.
Mechanical Installation
Install the R90C 4-Port Hub to allow access for functional checks,
maintenance, and service or replacement.
All mounting hardware is supplied by the user. Fasteners must be of sufficient
strength to guard against breakage. The use of permanent fasteners or locking
hardware is recommended to prevent the loosening or displacement of the
device. The mounting hole (4.5 mm) in the R90C 4-Port Hub accepts M4 (#8)
hardware. See the figure below to help in determining the minimum screw
length.
CAUTION: Do not overtighten the R90C 4-Port Hub’s mounting screw during installation. Overtightening can affect the performance of the R90C 4-Port Hub.
Status Indicators
The R90C 4-Port Discrete Bimodal to IO-Link Hub has matching amber LED indicators on both sides for each discrete device port to allow for installation needs and still provide adequate indication visibility. There is also an additional amber LED indicator on both sides of the converter, which is specific to the IO-Link communication.
Discrete Device Amber LEDs| IO-Link Communication Amber LED|
Power Indicator Green LED
---|---|---
Indication| Status| Indication| Status| Indication|
Status
Off| Discrete OUT is inactive| Off| IO-Link communications are not present|
Off| Power off
Solid Amber| Discrete OUT is active| Flashing Amber (900 ms On, 100 ms Off)|
IO-Link communications are active| Solid Green| Power on
Specifications
Supply Voltage
18 V DC to 30 V DC at 50 mA maximum
Supply Protection Circuitry
Protected against reverse polarity and transient voltages
Leakage Current Immunity
400 µA
Indicators
Green: Power
Amber: IO-Link communications
Amber: Discrete OUT status
Connections
(4) Integral 4-pin M12 female quick disconnect
(1) Integral 4-pin M12 male quick disconnect
Construction
Coupling Material: Nickel-plated brass
Connector Body: PVC translucent black
Vibration and Mechanical Shock
Meets IEC 60068-2-6 requirements (Vibration: 10 Hz to 55 Hz, 0.5 mm amplitude,
5 minutes sweep, 30 minutes dwell)
Meets IEC 60068-2-27 requirements (Shock: 15G 11 ms duration, half-sine wave)
Certifications
Environmental Rating
IP65, IP67, IP68
NEMA/UL Type 1
Operating Conditions
Temperature: –40 °C to +70 °C (–40 °F to +158 °F)
90% at +70 °C maximum relative humidity (non-condensing)
Storage Temperature: –40 °C to +80 °C (–40 °F to +176 °F)
Required Overcurrent Protection
WARNING: Electrical connections must be made by qualified personnel in
accordance with local and national electrical codes and regulations.
Overcurrent protection is required to be provided by the end-product
application per the supplied table.
Overcurrent protection may be provided with external fusing or via Current
Limiting, Class 2 Power Supply.
Supply wiring leads < 24 AWG shall not be spliced.
For additional product support, go to
www.bannerengineering.com.
| Supply Wiring (AWG) | Required Overcurrent Protection (Amps) |
|---|---|
| 20 | 5.0 |
| 22 | 3.0 |
| 24 | 2.0 |
| 26 | 1.0 |
| 28 | 0.8 |
| 30 | 0.5 |
Banner Engineering Corp. Limited Warranty
Banner Engineering Corp. warrants its products to be free from defects in
material and workmanship for one year following the date of shipment. Banner
Engineering Corp. will repair or replace, free of charge, any product of its
manufacture that, at the time it is returned to the factory, is found to have
been defective during the warranty period. This warranty does not cover damage
or liability for the misuse, abuse, or improper application or installation of
the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES
WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIMITATION, ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING
UNDER COURSE OF PERFORMANCE, COURSE OF DEALING, OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of
Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING
CORP. BE LIABLE TO THE BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA
COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR
SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY
TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT,
STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.
Banner Engineering Corp. reserves the right to change, modify or improve the
design of the product without assuming any obligations or liabilities relating
to any product previously manufactured by Banner
Engineering Corp. Any misuse, abuse, or improper application or installation
of this product or use of the product for personal protection applications
when the product is identified as not intended for such purposes will void the
product warranty. Any modifications to this product without prior express
approval by Banner Engineering Corp will void the product warranties. All
specifications published in this document are subject to change; Banner
reserves the right to modify product specifications or update documentation at
any time. Specifications and product information in English supersede that
which is provided in any other language. For the most recent version of any
documentation, refer to:
www.bannerengineering.com.
For patent information, see
www.bannerengineering.com/patents.
FCC Part 15 and CAN ICES-3 (B)/NMB-3(B)
This device complies with part 15 of the FCC Rules and CAN ICES-3 (B)/NMB-3(B). Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules and CAN ICES-3 (B)/NMB-3(B). These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the manufacturer.
© Banner Engineering Corp. All rights reserved
222806
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>