MONSTER MH11906 iSport Solitaire Lite Earphones User Guide
- June 5, 2024
- Monster
Table of Contents
MONSTER MH11906 iSport Solitaire Lite Earphones
Product Overview
- Headphone
- Eartips x 3 Pairs (M size is installed on the headset)
- SportClip™ x 3 Pairs (M size is installed on the headset)
- Charging C able
- Quick Start Guide & Warranty letter
- Volume Down Button, Track Forward
- Multi Function Button (MFB) (Power On/Play/Pause…)
- Volume Up Button, Track Back
- Indicator Light
- USB-C Charging Port
- MIC
Power On/Off
In power off mode, press and hold the MFB for about 2 seconds to power on the
headphones, the white indicator on for 1 second and you will hear “Power on”.
In power on mode, press and hold the MFB for about 5 seconds to power off the
headphones, the white indicator on for 1 second and you will hear “Power off”.
Pairing
In power off mode, press and hold the MFB for about 5 seconds until indicator
light flashes white, you hear “Power on”…”Pairing”. Now headphones are in
pairing mode. Activate Bluetooth® on your equipment and set it to search for
new devices (new Monster device). When the headphones are paired successfully,
“connected” will be heard.
Note : When you unbox the headphones and power it on for the first time,
it will enter to pairing mode automatically.
Music
Play/Pause: In the music playback mode, press the MFB to play/pause music.
Previous song: In the music playback mode, press and hold the Volume Down
Button for 2 seconds for previous song. Next song: In the music playback
mode, press and hold the Volume Up Button for 2 seconds for next song. Sound
characteristics: Press and hold the volume plus and minus 3 seconds, switch
from “Normal” to “Turbo” will have two “di di” beeps, and switch from Turbo to
Normal will have “di” beep.
Volume Control
Short press the Volume Up or Down Button to turn volume up or down, you hear
tone once you reach the maximum volume or minimum volume.
Call
Answer/End Call: short press the MFB. Reject Call: long press the MFB about 2
seconds.
Voice Control
After connecting to the phone, quickly double press the MFB to activate the
voice assistant.
LED Guide to Indicator Lights
Mode
| ****
Description
| ****
Voice prompts
---|---|---
Power On
| ****
White LED indicator lights for about 1 second
| ****
“Power On”
Power Off
| ****
White LED indicator lights for about 1 second
| ****
“Power Off”
Pairing
| ****
White LED flashes quickly
| ****
“Pairing”
Connected
| ****
No function operation, the indicator light is off
| ****
“connected”
Charging| The white LED indicator lights up when charging, and turns off when fully charged| ****
–
Note:
- Please put the earphones in the correct position to charge.
- It is not recommended to replace the battery privately.
- The battery (battery pack or combination battery) must not be exposed to excessive heat such as sunlight or fire.
FCC Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>