ONFORU D100BL LED Floodlight Instruction Manual
- June 5, 2024
- ONFORU
Table of Contents
LED FLOODLIGHT
Product Manual
MODEL:
- D100BL
- G50BL
SAFETY INFORMATION
Disconnect the power supply before attempting any work on the unit!
-
Installing these units involves work on the mains voltage supply; installation must therefore be carried out professionally in accordance with the appliance national wiring regulations and electrical operating conditions.
-
The product must be installed by a licensed professional electrician.
-
Check all components for damage, do not use the product if it is damaged.
-
To ensure the product can work normally, please use it in the voltage within the range on the lamp label.
-
The floodlight enclosure heats up when the light is on. Please adjust the angle of the light after the power is off for 10-15 minutes. Do not look into the LED light at a short range or for any prolonged period(>5 min).
-
Do not install the unit on (normally) flammable surfaces.
-
Do not alter or change parts of the light at will, in case of the accidents such as breakage, fall, electric shock, fire, etc.
-
To reduce the risk of strangulation the flexible wiring connected to this luminaire shall be effectively fixed to the wall if the wiring is within arm’s reach
-
The light is IP66 waterproof, but the plug is non-waterproof. Please connect the plug indoors or connect to a socket that provides IP65 protection.
-
Please use tools to adjust the lights.
-
The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced.
-
Never plug the light in with wet hands in case of electric shock.
-
This light is a non-dimmable product. To avoid failure, please don’t connect it with the dimming controller.
-
Do not connect this light fixture to an ungrounded electrical system.
WARNING: Installing this light in an ungrounded electrical system may cause the metal parts of the light to carry current if any wires or wire connections are damaged or loose. In this case, anyone who touches the light will receive an electric shock, resulting in injury or death. -
Be sure to use wire nuts/connectors rated for the correct gauge and number of wires used.
NOTE: Make sure there are no exposed wire bundles outside the wire nut/connector (if applicable). -
Be careful not to damage or cut the wire insulation (covering) during installation. Do not let the wires touch any sharp edges.
-
The floodlight is supplied with cable and must be terminated using a terminal block (not supplied) in a suitable IP-rated enclosure (not included).
-
For type Z attachments: The external flexible cable or cord of this luminaire cannot be replaced; if the cord is damaged, the luminaire shall be destroyed.
-
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.
NOTE:
FCC Warning:
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator & your body
PARAMETER
| A-330x35x306 mm / 12.99×1.36×12.05 in
B-242x39x256 mm / 9.52×1.53×10.07 in
---|---
| A- 1.74 kg / 3.83 lb
B- 0.80 kg / 1.76 lb
**| 100-120V ～ 60Hz 220-240V ～ 50Hz
| RGB/2700 ～ 6500K
| IP66
PF| ＞0.5
ta**|
Max Projected Area
A: 0.0243m² B: 0.0616m²
Max. Lighting Coverage
A: 80m² B: 160m²
PAIRING LED LIGHT WITH”Onforu” App.
NOTE:
Turn ON/OFF the Smart LED Light three times until the LED light starts to
flash quickly, which indicates the success of the factory reset.
Step 1: “Onforu” App Download.
There are 2 options for obtaining and downloading the “Onforu” App on your
smart device.
1. Scan the QR code on the right.
2. Search for “Onforu” in the App Store or Google Play.
https://a.smart321.com/wwwyouliang
Step 2: Enter the “Onforu” App. and register an account and log in. If
you already have an account for Smart Life App., Please select “Log in with
existing account”.
Note: You will need your “Onforu” App. username and password to pair with
Amazon Alexa and/or Google Assistant.
Step 3. Please turn on the Bluetooth before connecting LED lights to the
“Smart Life” APP.
Tap the “+” button on the top right corner to add a device, then tap”lighting
device” to enter the next page.
Note: This smart LED Light can only support a 2.4 GHz network and cannot
work with a 5.0 GHz network. Please check if your home network is 2.4 GHz and
make sure that your phone has been connected to your Wi-Fi network. Please
ensure your network is not hidden.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>