Klim PANTHER Wireless Gaming Headset User Manual

: June 5, 2024
: KLIM

Table of Contents

Klim PANTHER Wireless Gaming Headset
PRODUCT DIAGRAM AND PACKAGE CONTENTS
HEADSET CONTROLS
FIRST USE
OTHER FUNCTIONS
WARNINGS AND SAFETY PRECAUTIONS
CONTACT AND TROUBLESHOOTING
TECHNICAL SPECIFICATIONS
Documents / Resources
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)

Klim PANTHER Wireless Gaming Headset

PRODUCT DIAGRAM AND PACKAGE CONTENTS

Package contents

Wireless headset
USB wireless transmitter
USB-C charging cable 3.5 mm audio cable
User m□nu□I

DIAGRAM:

Speaker mute button 2 LED light switch
Volume controller
3.5 mm audio port
USB-C charging port
LED indictor
Microphone LED indictor
Microphone
Power button Ploy/Pause
Microphone mute
Next track
Previous track
USB transmitter 14 Transmitter button
Transmitter LED indicator

Light indicator (headset)

Pairing: flashing in blue and green alternatively
Power on: fixed blue
The wireless mode: flashing in blue while music is playing. Fixed blue when poused
Charging status: fixed orange while charging, which turns off when fully charged.

Light indicator (USB transmitter)

Pairing: blue light flashes
Disconnected: fixed red light
Connected: fixed blue light
Reset state: fixed blue and red light

HEADSET CONTROLS

Power button: press and hold C, for 3 seconds to turn the headset on or off. Play: short press the C, button while music is paused.
Pause: short press the C) button while music is playing.
Next track: Press to go to the next track
Previous track: Press to go to the previous tr□ck
Volume controller: slide to + / – to turn the volume up or down.
Speaker mute: press and hold to mute/unmute sound.
Microphone mute: press I to mute/unmute the microphone. The microphone LED indicator is blue while the microphone is active and off while inactive.
RGB lights: press and hold-‘t’-for 2 seconds to turn the RGB lights on and off.
NOTE: while in Wired mode [using the 3.5 mm port), only the volume slider works. To use oil buttons, activate o wireless mode [Bluetooth or USB receiver),

PHONE CALLS

Answer call: short press during on incoming coll
Reject call: long press during on incoming coll
Hang up: short press while in on active coll While connected to o phone, press twice to diol the lost phone number in your coll record [compotible devices only).

FIRST USE

Note: it is highly recommended to run o full charging cycle before using the headset for the first time. Refer to the section “charging the battery” for charging instructions.

Wired Mode
Connect one end of the 3.5 mm cable to the AUX port on the headset and the other end to o compatible port in your device.
Note: both audio and microphone are compatible while in wired mode, as long as the port supports audio and microphone connections at the some time. If your device hos one port for audio and one port for microphone, please use o 3.5 mm audio/mic splitter cable [not included),
USB Transmitter

Insert the wireless transmitter into the USB port of your device. Once the driver finishes its automatic installation, the transmitter enters a stand-by state and the light indicator turns red.
Turn on the wireless headset: it automatically enters pairing mode. Press and hold the button on the wireless transmitter for 3 seconds to pair the headset to the transmitter. The light indicator flashes in blue quickly.
Once the headset is paired with the transmitter, the light indicator stays lit on blue. After o successful pairing, every time you turn on the headset it connects aoutomotirnlly to your device.

Bluetooth

If the headset is not paired to any device, it enters pairing mode Aoutomotirnlly and the light flashes in blue and green alternatively,
If they have been paired with a different device before, reset any previous connections by pressing both and for 3 seconds.
When in pairing mode:

Activate Bluetooth on your device and open the list of available Bluetooth connections.
Select KLIM Panther to pair the headset with your device.
The light indicator turns blue and the headset is connected.

After o successful pairing, every time you turn the headset on it connects Aoutomotirnlly to your device.
Note: You can only have 1 device connected ot some time. When using the USB transmitter, the Bluetooth connection is deactivated, and vice-versa.

OTHER FUNCTIONS

Charging the battery
Connect the USB charging cable to your computer or another compatible charger [5V /lA or 5V /2AJ, Connect the other end of the cable to the headset. The light turns orange while charging ond turns off completely once the charge has finished.
IMPORTANT: oil wireless modes ore deactivated during the charge, Plug in the 3.5 mm cable to your computer to continue using the headset while it charges, Note: when connected to some i□S devices, the battery status will be shown on the device’s screen [usually the top-right corner).

RGB LIGHTS

Press ond hold the RGB lights button for 2 seconds to turn the lights on or off. Short press to change the light color/effect. The RGB lights are always off while the headphone is charging or in wired mode.
Hint: turning off the RGB lights extends the duration of the battery.

Bluetaath connection reset
Press both and ot some time for 3 seconds. The green and blue LED stays on for 3 seconds, and then the headset enters pairing mode, with the green and blue LED flashing alternatively,

USB wireless transmitter instructions
Power on: plug in the transmitter to the computer and it turns on outomoticolly Power off unplug the wireless transmitter Pairing mode: press and hold the button on the transmitter for 3 seconds to enter pairing mode. The blue light flashes quickly and the headset con be connected. Disconnect: short press the button on the transmitter to deactivate the connection. The light indicator stays red while disconnected. Clear connection: press and hold the button on the transmitter for B seconds. The light indicator stays red and blue while oil connections are cleared.

WARNINGS AND SAFETY PRECAUTIONS

Always charge the headphones with o 5V /1A or 5V /2A charger. Higher voltage may damage the headphones. Fully charge the headphones after they’ve been unused for 3 months. If you don’t intend to use them for o long period of time, charge it every 3 months to protect the battery, Use the headphones in normal temperature and humidity conditions. Avoid exposing them to direct sunlight for extended periods of time. not submerge the headset in water, always keep dry; keep away from fire and other hot objects. disassembling electronic parts or performing repairs should only be performed by qualified personnel. If you experience any trouble with the product, please contact us.

CONTACT AND TROUBLESHOOTING

Do you need additional assistance with your product? Contact us at support@klimtechnologies.com. Our team of specialists is at your disposal and will always reply within 24 hours!
Q: The headset does not work
A: Carry out the following verifications:

Check that the battery is charged
Check that the headset is correctly paired with the USB receiver [blue light). If not, reset the connection and pair again.
Check that the sound is not set too low on the volume knob and that the speakers are not muted vi□ the speaker mute button on the headset.
Check that the correct playback device is selected on your computer /console and that the volume level in the settings screen is adequate

Q: The microphone does not work
A: Carry out the following verifications:

heck that the microphone is not muted vi□ the mute microphone button
Check that the correct recording device is selected on your computer /console and that the microphone volume level in the settings screen is adequate.
Check the voice activation settings in your recording software [push-to-toll< or voice activation, and verify that it is properly set up,