KLIM 20211122 Wireless Keyboard User Manual

20211122 Wireless Keyboard
User Manual

PACKAGE CONTENTS AND PRODUCT DIAGRAM

QUICKSTART GUIDE

Wired mode

Wired mode: connect the USB cable to the keyboard, and then connect it to your computer. Flick the switch behind the keyboard to the ON position. Press the mode switch underneath the keyboard until it is set to “Wired” (orange light).

Wireless mode (2.4G)

Wireless mode (USB receiver): take the wireless USB receiver from behind the keyboard and connect it to your computer. Flick the switch behind the keyboard to the ON  position. Press the mode switch underneath the keyboard until it is set to “2.4G mode” (green light).

Bluetooth mode

Bluetooth mode: Press the mode switch underneath the keyboard until it is set to “Bluetooth” (blue light). Press FN + Q for 3 seconds to look for compatible devices. The light starts blinking to indicate its pairing status. Go to the device you want to pair the keyboard to and select KLIM Shift 5.0 / 3.0 to establish the connection. For detailed Bluetooth instructions and pairing of multiple devices, please check the Bluetooth Connection Mode section on the next page.

IMPORTANT: on any mode, make sure that the ON/OFF switch is set to ON and that the correct mode is selected underneath the keyboard.

CHARGING THE BATTERY

Battery indicators

The light on the spacebar indicates the status of the battery:

White light: full battery.
Yellow light: charging.
Red light (flashing): low battery.

When the keyboard battery is low, connect the cable to your computer or an external power source (such as a USB charger to charge your keyboard. You may continue to use it while it charges.

Tip: lowering the brightness or switching off the RGB lighting completely significantly increases the battery life and reduces the frequency of charges.

Power saving function

In order to preserve battery life, the keyboard lights turn off after 7 minutes of inactivity while on a wireless connection (2.4G or Bluetooth). The keyboard enters a stand-by mode after 30 minutes of inactivity. Ending any wireless connection also puts the keyboard on stand-by mode.

BLUETOOTH MODE

Note: for basic pairing instructions, check the Quick Start Guide in the previous page.

You can pair up to 3 devices at the same time and quickly switch between them, by following the pairing steps detailed in the quick start guide with each of the available keys  (Q, W, E).

Each key has a different light indicator (blue, cyan, purple). While pairing mode is active, the light flashes. Once the keyboard has been paired with the device on the selected key  (Q, W or E), the light will become still and then turn off. If pairing is not completed within 2  minutes, the pairing process stops and the light turns off.

When multiple devices are paired, simply press FN + Q/W/E to select each one. The corresponding light blinks once and then turns off.

Note: depending on your Operating System, one or two device names may appear (KLIM Shift 3.0 or KLIM Shift 5.0). When available, it is recommended to select 5.0.

KEYBOARD SHORTCUTS & THE FN KEY

This is a compact keyboard that does not have the usual 104/105 keys of a full-sized one. However, fear not! You can still access every key and even multimedia shortcuts thanks to the FN key. Simply press and hold the FN key while you press other keys on the keyboard.

The diagram below indicates the location of each set of special function keys:

Red: multimedia
Blue: function keys
Green: backlighting adjustment
Yellow: other

Tip: the small white text/icons indicate the function of that key when pressing it along the FN key.

*diagrams correspond to the US layout, some keys vary in the UK layout

Backlight adjustments

Change backlighting effects, colors, brightness, and speed using these shortcuts. For advanced color customization, you may download our dedicated drivers at www.klimtechs.com/drivers

| Change mode| | Decrease brightness
---|---|---|---
| Change color| | Reduce effect speed
| Increase brightness| | Increase effect speed

Function keys

This set of keys allows you to access the F1-F12 keys as well as the Print screen, Insert, Home, and End.

| Print screen| 5 %
F5| F5
---|---|---|---
Del
Ins| Insert| 6∨
F6| F6
PgUp
Home| Home| 7 &
F7| F7
PgDn
End| End| 8*
F8| F8
1!
Fl| Fl| 9 (
F9| F9
2@
F2| F2| F10| F10
3#
F3| F3| _
F11| F11
4$
F4| F4| = +
F12| F12

Multimedia shortcuts

| Media Player| | Stop
---|---|---|---
| Volume down| | Previous track
| Volume up| | Play/pause
| Mute sound| | Next track

Other shortcuts

| Restore original settings: FN + ESC for 3 seconds,
---|---
| Restore Bluetooth settings: FN + TAB for 3 seconds,
| Windows lock: FN + WIN to lock/unlock the Windows key,
| Select/Pair Bluetooth device 1
| Select/Pair Bluetooth device 2
| Select/Pair Bluetooth device 3
| The keyboard’s default mode is Windows, If using a Mac
computer, press FN + Z to swap the functions of the
Control, Win, and Alt keys to match the Control,
Command and Option keys on a Mac keyboard, Press FN
+ X to return to the normal Windows keys parameters,

KEYBOARD CUSTOMIZATION

Replacing the keycaps

This keyboard includes a set of spare white keycaps that you can install to give your keyboard a unique look. Use the keycap removal tool to extract the keycaps by pressing down until the keycap is hooked, then pulling up. Take the replacement keycap and install it by aligning it with the switch and firmly pressing down.

Tip: make sure you place them in the right position! Otherwise, it can be confusing to use the keyboard (unless you’re a touch typing master, that is).

Here are some layout ideas:

Frame/frameless mode

The frame of the keyboard is removable. Grab the keyboard and push down with your thumbs while pulling the frame upwards.
To reinstall it, simply place it in position again until it is magnetically attached.

Replacing the switches (advanced users only!)

This keyboard is hot-swappable, which means you can swap the switches without any soldering. Here are the instructions on how to go about it:

1. Use the key removal tool to extract the keycaps (as explained in the previous section).
2. Clamp the front and back of the switch (NOT the left and right) using a switch puller and pull up until you completely remove the switch.
3. Take the new switch and push it down with your hand until it is set in place. Pay attention to the switch orientation and make sure the pins are properly aligned!
4. Reinstall the keycap by hand and enjoy your new switches!

TROUBLESHOOTING

If the problem persists, contact us at support@klimtechnologies.com. Our team of specialists is at your disposal and will always reply within 24 hours!

the ON position.
2 Charge the battery.
3. Check that the USB plug (wired or wireless) is properly connected.
4. Check that the correct mode is selected on the Mode Button underneath the keyboard.
The keyboard sometimes stops working temporarily while on 2.4G Wireless Mode.| 1. Make sure that there are no obstacles between the keyboard and the Wireless receiver.
2. Check the battery charge,
3. Make sure you have not exceeded the maximum usage distance.
The keyboard sometimes inputs two presses instead of one| This is known as key chattering and may affect some mechanical keyboards. Remove the keycap and firmly press the switch downwards using a thin tool (make sure it’s not sharp!) a few times, then reinstall the keycap and try again.
The Windows key doesn’t work| Check that the Windows lock is not activated (press FN + WIN key).
The Ctrl/Alt/Windows keys do not work properly| Check that the keyboard is in the correct OS mode (Windows/Mac) by pressing FN + Z/X ,
Bluetooth mode does not work| 1. Check that Bluetooth Mode is selected on the Mode Button underneath the keyboard.
2. Make sure that the device you want to pair the keyboard with is looking for devices when you want to pair it.
3. Try selecting a different Bluetooth Device if available (3.0 / 5.0),
4. Make sure that you have selected the correct device via the FN+Q/W/E keys.
My Wireless USB receiver is not detected.| If the keyboard does not recognize the USB receiver, try pairing them again. Unplug the USB receiver. Select 2.4G mode via the button under the keyboard: the green light will turn on for 1 second and then turn off. Press and hold FN + R for more than 3 seconds, then plug in the USB receiver to pair it,

Technical specifications

Wireless
distance| up to 10 m
Battery capacity| 3,7 V 2000 mAh
Charging time| 3 hours
Charging voltage| 5 V
Charging current| 3 V 1000 mA
Continuous usage time at max. brightness| 10 hours
Key life expectancy| 50 million clicks
Energy saving
auto stand-by| 7 minutes
Switch type| Brown (hot-swappable)
Supported OS| Windows, macOS, iOS, Android

WWW.KLAMTECHS.COM 

Authorized EU representative
Marcus Excelsior Limited
Bracken Road No 51, Carlisle Offices
D18CV48 Dublin, Sandyford
Dublin, Ireland

Marcus Excelsior Limited
2512 Longhorn Place Office Tower
8 Argyle Street, Mongkok, Kowloon Hong Kong

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>