KLIM K-PR-1 Panther Wireless Gaming Headset User Manual

KLIM K-PR-1 Panther Wireless Gaming Headset

Package contents

• Wireless headset
• USB wireless transmitter
• USB-C charging coble
• 3.5 mm audio coble
• User manual

Diagram

1. Speaker mute button
2. LED light switch
3. Volume controller
4. 3.5 mm audio port
5. USB-C charging port
6. LED indictor
7. Microphone LED indictor
8. Microphone
9. Power button Play/Pause
10. Microphone mute
11. Next track
12. Previous track
13. USB transmitter
14. Transmitter button
15. Transmitter LED indicator

Light indicator (headset)

• Pairing: flashing in blue and green alternatively
• Power on: fixed blue
• Wireless mode: flashing in blue while music is plying. Fixed blue when paused Charging status: fixed orange while charging, which turns off when fully charged.

Light indicator (USB transmitter)

• Pairing: blue light flashes
• Disconnected: fixed red light
• Connected: fixed blue light
• Reset state: fixed blue and red light

HEADSET CONTROLS

Power button: press and hold  for 3 seconds to turn the headset on or off.
Play: short press the button while music is paused.
Pause: short press the button while music is playing.
Next track: Press to go to the next track
Previous track: Press to go to the previous track
Volume controller: slide to + / – to turn the volume up or down.
Speaker mute: press and hold to mute/unmute sound.
Microphone mute: press to mute/unmute the microphone. The microphone LED indicator is blue while the microphone is active and off while inactive.
RGB lights: press and hold for 2 seconds to turn the RGB lights on and off.

NOTE: while in Wired mode [using the 3.5 mm port), only the volume slider works. To use oil buttons, activate o wireless mode [Bluetooth or USB receiver),

Phone calls

• Answer call: short press during on incoming call
• Reject call: long press during on incoming call
• Hang up: short press while in on active call

While connected to o phone, press twice to diol the lost phone number in your call record [compatible devices only).

First Use

Note: it is highly recommended to run o full charging cycle before using the headset for the first time. Refer to the section “charging the battery” for charging instructions.

Wired Mode
Connect one end of the 3.5 mm coble to the AUX port on the headset, and the other end to o compatible port in your device.
Note: both audio and microphone ore compatible while in wired mode, as long as the port supports audio and microphone connections at the some time. If your device hos one port for audio and one port for microphone, please use o 3.5 mm audio/mic splitter coble [not included),

USB Transmitter

1. Insert the wireless transmitter into the USB port of your device. Once the driver finishes its automatic installation, the transmitter enters a stand-by state and the light indicator turns red.
2. Turn on the wireless headset: it automatically enters pairing mode. Press and hold the button on the wireless transmitter for 3 seconds to pair the headset to the transmitter. The light indicator flashes in blue quickly.
3. Once the headset is paired with the transmitter, the light indicator stays lit on blue.

After successful pairing, every time you turn on the headset it connects automatically to your device.

Bluetooth
If the headset is not paired to any device, it enters pairing mode automatically and the light flashes in blue and green alternatively,
If they hove been paired with a different device before, reset any previous connections by pressing both and  for 3 seconds.

When in pairing mode:

1. Activate Bluetooth on your device and open the list of available Bluetooth connections.
2. Select KLIM Panther to pair the headset with your device.
3. The light indicator turns blue and the headset is connected.

After o successful pairing, every time you turn the headset on it connects automatically to your device.

Note: You con only hove 1 device connected at the some time. When using the USB transmitter, the Bluetooth connection is deactivated, and vice versa.

Other Functions

Charging the battery
Connect the USB charging coble to your computer or other compatible charger [5V /lA or 5V /2AJ, Connect the other end of the coble to the headset.
The light turns orange while charging and turns off completely once the charge hos finished.

IMPORTANT: oil wireless modes ore deactivated during the charge, Plug in the 3.5 mm coble to your computer to continue using the headset while it charges,
Note: when connected to some iOS devices, the battery status will be shown on the device’s screen [usually the top-right corner).

RGB Lights

Press and hold the RGB lights button for 2 seconds to turn the lights on or off. Short press to change the light color/effect. The RGB lights ore always off while the headphone is charging or in wired mode.
Hint: turning off the RGB lights extends the duration of the battery.

Bluetooth connection reset
Press both   and   at the some time for 3 seconds. The green and blue LED stays on for 3 seconds, and then the headset enters pairing mode, with the green and blue LED flashing alternatively,

USB wireless transmitter instructions

• Power on: plug in the transmitter to the computer and it turns on automatically
• Power off: unplug the wireless transmitter
• Pairing mode: press and hold the button on the transmitter for 3 seconds to enter pairing mode. The blue light flashes quickly and the headset con be connected.
• Disconnect: short press the button on the transmitter to deactivate the connection. The light indicator stays red while disconnected.
• Clear connection: press and hold the button on the transmitter for B seconds. The light indicator stays red and blue while oil connections ore cleared.

WARNINGS AND SAFETY PRECAUTIONS

• Always charge the headphones with o 5V /1A or 5V /2A charger. Higher voltage may damage the headphones.
• Fully charge the headphones After they’ve been unused for 3 months. If you don’t intend to use them for o long period of time, charge it every 3 months to protect the battery,
• Use the headphones in normal temperature and humidity conditions. Avoid exposing them to direct sunlight for extended periods of time.
• Do not submerge the headset in water, always keep dry; keep away from fire and other hot objects.
• Disassembling electronic parts or performing repairs should only be performed by qualified personnel. If you experience any trouble with the product, please contact us.

CONTACT AND TROUBLESHOOTING
Do you need additional assistance with your product? Contact us at support@klimtechnologies.com. Dur team of specialists is at your disposal and will always reply within 24 hours!

• Q: The headset does not work
  A: Carry out the following verifications:

1. Check that the battery is charged
2. Check that the headset is correctly paired with the USB receiver [blue light). If not, reset the connection and pair agaoin.
3. Check that the sound is not set too low on the volume knob, and that the speakers are not muted via the speaker mute button on the headset.
4. Check that the correct playback device is selected on your computer /console, and that the volume level in the settings screen is adequate

• Q: The microphone does not work
  A: Carry out the following verifications:

1. Check that the microphone is not muted via the mute microphone button
2. Check that the correct recording device is selected on your computer /console, and that the microphone volume level in the settings screen is adequate.
3. Check the voice activation settings in your recording software [push-to-toll< or voice activation verify that it is properly set up.

TECHNICAL SPECIFICATIONS

USB transmitter

Headset

Microphone

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>