VAPORESSO Target 80 60W Pod Mod kit User Manual

: June 5, 2024
: VAPORESSO

Table of Contents

SPECIFICATIONS
PACKING LIST
EXPLODED VIEW
FIGURES
USE INSTRUCTIONS
PROTECTIONS
CAUTIONS
WARNINGS
Documents / Resources

60W Pod Mod kit
User Manual

Thank you for choosing the Vaporesso product. Please read this instruction carefully before use to ensure a perfect experience. If there is any additional requirement about this product, please consult the local agent or contact us through our website: www.vaporesso.com

SPECIFICATIONS

Dimensions: 130.9 x 38.3 x 30.8mm
POD Capacity: 5ml/2ml(TPD)
Coils & Suggested Wattage:
GTX 0.2 MESH Coil (45-60W)
GTX 0.3 MESH Coil (32-45W)
Battery Capacity: 3000mAh
Output Power : 5-80W
Charging Current: DC 5V/2A,Type-C
Battery Display : 0.96” TFT Screen

PACKING LIST

1 x TARGET 80 MOD
1 x GTX PODTANK 26 (5ml/2ml TPD)
1 x GTX 0.2 MESH Coil (In-BOX)
1 x GTX 0.3 MESH Coil (In-BOX)
1 x Type-C Cable
1 x User Manual
1 x Warranty Card

EXPLODED VIEW

FIGURES

Figure 1: Replace the coil

Figure 2: Fill e-liquid

USE INSTRUCTIONS

Install the Tank
Install the Tank to the battery by screwing the 510 thread. Make sure they are firmly connected
Replace the Coil
– Place the drip tip of the pod face down, and pull out the used coil;
– Install a new coil to the pod;
– Press the coil to align the coil base with the pod.

Refer to figure 1. 3. Fill E-liquid
– Unscrew the top cap from the pod;
– Fill e-liquid through the filling slot;
– Screw the top cap to reinstall it back into place as shown;
– Please wait 5 minutes for the e-liquid to soak into the coil completely.
* Refer to figure 2.
1. Adjust the Airflow
  Please rotate the pod to match the air-inlet port to adjust the airflow volume.
2. Power On/Off the Device
  Power on/off: press the power button 5 times in 2s.
3. Power Adjustment
  TARGET 80 Kit is using the powerful GTX coil platform, and the suggested power needs to be noticed before starting vaping.
4. Start Vaping
  Press the power button to enjoy an extraordinary vaping experience.
5. Charge the Battery
  After connecting the Type-C cable to the battery, the battery indicator and remaining charging time will be shown on the screen.
6. Lock or unlock the device
  Press the fire button 3 times, then the +, – and mode buttons will be locked. In the same way, the buttons will be unlocked and the screen will be unlocked.
7. Choose a Model
  1. Long press the mode button for main mode selection (Pulse Mode/F(t) Mode/VWN Mode).
  2. Press the mode button 3 times continuously for the secondary menu setting.

*F(t): F(t) MODE (DEFAULT)* F(t) MODE is by adjusting temperature, heating speed and time, F(t) mode releases the flavors of e-liquid adequately, delivering the perfect balanced tasting experience consistently from the first puff throughout.
DIY: DIY**

MODE You can choose traditional VW (H, N, S), VV, BP (Bypass) modes in this section.
*PUL: PULSE MODE (DEFAULT)* PULSE MODE: It’s a mode to improve the vaping experience through constant voltage output, delivering optimal flavor production, throat hit, nicotine satisfaction, and perfect temperature cloud continuously.
SET: SYSTEM SET** System setting includes DEFAULT, SMART VW, PUFF, and VERSION options. SMART VW: when this function is turned on and a POD is installed, the system will recommend the best power.

PROTECTIONS

Short circuit protection & Low resistance protection:
When the load resistance is less than 0.1±0.01, pressing the power button could trigger the short circuit protection or Low resistance protection, the device will close the output, at the same time OLED display will show “SHORT ATOMIZER”.
No-load protection:
When no load resistance is detected, pressing the power button could trigger the no-load protection, the device will close the output, at the same time OLED display will show “CHECK ATOMIZER”.
High resistance protection:
When the load resistance is greater than 5±0.5, pressing the power button could trigger the high resistance protection, the device will close the output, at the same time OLED display will show ” CHECK ATOMIZER “.
Low voltage protection:
When the voltage of the battery cell is lower than 3.3±0.1V, pressing the power button could trigger the low voltage protection, the device will close the output, at the same time OLED display will show “LOW BATTERY”.
PCBA(Printed Circuit Board Assembly):
When the temperature of the PCBA(Printed Circuit Board Assembly) temperature sensor is higher than 70+5 /-10, pressing the power button could trigger the PCBA (Printed Circuit Board Assembly) overheat protection, the device will close the output, at the same time OLED display will show “OVERHEAT”.
Over-discharge protection:
During the process of smoking, when the battery cell voltage is lower than 2.9±0.1V, the device will close the output automatically.
Overcharge protection:
During charging, when the battery cell voltage is greater than 4.1±0.1V, the OLED display will show “100%”. At the end of charging, the battery cell voltage will not exceed 4.2±0.03V.
Auto-shutoff protection:
When the POWER button is held for 10±1 seconds, the device will close the output, at the same time OLED display will show “OVERTIME”.
Battery cell anti-reverse connection protection:
The inversion of the battery cell will not damage the battery.

CAUTIONS

Please turn off the device when it is not in use.
Do not leave the charging device unattended.
Do not drop, throw or abuse your device, which may cause damage.
Please use a standard USB output charger with a proper charging current and voltage range.
Keep away from the water or any flammable gas, or liquid.
Do not expose the device to direct sunlight, dust, moisture, or mechanical shock.
Do not expose the device to extreme temperature. (Recommended temperature range: -10~60 /14~140 while using and -10~45 /14~113 while storing).
EEE Recycling: the product should not be treated as household waste, instead, it should be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
Battery Recycling: the product battery should not be treated as household waste, instead, it should be handed over to the application used battery collection point for recycling.
Only have your device repaired by Vaporesso. Do not attempt to repair it by yourself as damage or personal injury may occur.

WARNINGS

This refillable electronic cigarette is intended for use with compatible e-liquid, which may contain nicotine. Nicotine is an addictive substance and it is not suitable or recommended to use in the following cases:

This device is not suitable for:
– Persons under the legal smoking age
– Persons experiencing heart disease, stomach or duodenal ulcers, liver or kidney problems, long-term throat disease, or difficulty breathing due to bronchitis, emphysema, or asthma.
– Persons with an overactive thyroid gland or experiencing phaeochromocytoma (a tumor of the adrenal gland that can affect blood pressure).
– Persons taking certain medications like Theophylline, Ropinirole or Clozapine and etc..
This device is not recommended for:
– Non-smokers
– Pregnant or breastfeeding women
You may experience the following results if you use nicotine-containing e-liquid with this product. If it happens, please consult a healthcare professional and show them this leaflet if possible:
– Feeling faint – Nausea – Dizziness – Headache – Coughing
– Irritation of the mouth or throat – Stomach discomfort – Hiccups
– Nasal congestion – Vomition – Chest palpitations/pain or an irregular heart rate