VAPORESSO TX80 Forz Waterproof Shockproof and Dustproof User Manual

: June 5, 2024
: VAPORESSO

Table of Contents

SPECIFICATIONS
PACKING LIST
Figure 1 Replace the Coil
Figure 2 Fill E-liquid
EXPLODED VIEW
USE INSTRUCTIONS
PROTECTIONS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

VAPORESSO FORZ TX80
User Manual

Thank you for choosing the Vaporesso product. Please read this instruction carefully before use to ensure a perfect experience. If there is any additional requirement about this product, please consult the local agent or contact us through our website: www.vaporesso.com

SPECIFICATIONS

Dimensions: 133.141.730.1mm
Coils:
GTR 0.15Ω MESH Coil (60-80W)
GTR 0.4Ω MESH Coil (40-60W)
Tank Capacity: Standard: 4.5ml / TPD: 2.0ml
Output Power: 5-80W
Battery Capacity: 1 x 18650(not included)
Display: 0.69″ OLED Screen
Charging Current: DC 5V/2A, Type-C
Tank Connection: 510 Thread

PACKING LIST

1 x FORZ TX80 MOD
1 x FORZ TANK 25 (Standard: 4.5ml/TPD:2ml)
1 x GTR 0.15Ω Mesh Coil (Pre-installed)
1 x GTR 0.4Ω MESH Coil (In Box)
1 x Type-C USB Cable
1 x Drip Tip Cover| 1 x Glass Tube
4 x O-ring
1 x Screwdriver
1 x USB Silicone Plug
1 x FORZ Badge
1 x User Manual
1 x Warranty Card
---|---

Figure 1 Replace the Coil

VAPORESSO TX80 Forz Waterproof Shockproof and Dustproof - Replace the
Coil

Figure 2 Fill E-liquid

VAPORESSO TX80 Forz Waterproof Shockproof and Dustproof - Fill E
liquid

EXPLODED VIEW

VAPORESSO TX80 Forz Waterproof Shockproof and Dustproof - EXPLODED
VIEW

USE INSTRUCTIONS

Install the Tank
Install the tank to the battery by screwing the 510 thread. Make sure they are firmly connected.
Replace the Coil (Please check the Figure 1 on page 1)
– Unscrew the thread base from the tank;
– Pull out the used coil in the tank;
– Install a new coil to the tank;
– Reattach the thread base into place.
Fill the E-liquid (Please check the Figure 2 on page 1)
– Unscrew the top cap from the tank;
– Fill e-liquid through the two filling slots;
– Reattach the top cap back into place;
– Please wait 5 minutes for the e-liquid to soak into the coil completely.
Adjust the Airflow
To adjust the airflow volume, please rotate the air-inlet ring on the bottom of the tank.
Start Vaping
Press and hold the power button to start vaping. For your safety, please do not vape for more than Los at a time.
About Charging
After the Type-C USB cable is connected to the battery, the screen indicator and remaining charging time will be displayed on the screen.
Lock/Unlock the Buttons
Press the power button 3 times continuously to lock or unlock the “+” button, “-” button, and mode button. The power button still works.
Choose a Mode
Press the mode button 3 times continuously or long-press the mode button to start the mode setting.
*F(t): F(t) MODE (DEFAULT)
* After the atomizer is installed, the device will enter the F(t) MODE automatically. By adjusting temperature, heating speed, and time, F(t) mode releases the flavors of e-liquid adequately, delivering the perfect balanced tasting experience consistently from the first puff throughout.
PUL: PULSE MODE
It’s a mode to improve the vaping experience through constant voltage output, delivering optimal flavor production, nicotine satisfaction, and perfect temperature cloud continuously.
ECO: POWER ECO MODE
When the battery level is below 40% and unable to support the preset power, the device will automatically provide an option to enter the POWER ECO mode for increasing endurance.
STC: SMART TEMPERATURE CONTROL MODE
When the temperature heating wire (SS/Ti/Ni) is detected, the device will provide an option to enter the STC (Smart TC) mode automatically.
DIY: DIY MODE
You can choose traditional VW (H, N, S), VV, VT, BP (bypass), and SP (super player) modes in this section. When the coil resistance is extremely low, the device will provide an option to enter the SP (Super Player) mode automatically.
SET: SYSTEM SETTING
System setting includes brightness, flip screen, smart VW on/off, Auto Eco on/off, default and version settings, the operating interface can be customized by yourself.
Smart VW: when this function is turned on and an atomizer is installed, the system will recommend the best power for the user.
Auto Eco:** When the battery level is below 40% and unable to support the preset power, the device will automatically enter the POWER ECO mode for increasing endurance.
DIY MODE
*VWS/VWN /VWH (Variable Wattage Mode)
VWH: high start-up speed
VWN: normal start-up speed
VWS:* soft start-up speed
VT-SS/VT-NI/VT-TI/VT-MI
(Variable Temperature Control Mode)
The SS, NI, and TI modes are only available for the Stainless Steel SUS316L, Nickel 200, and Titanium materials respectively. Choose the MI mode to make a customized setting when other heating wire materials are installed.
VV (Variable Voltage Mode)
Customize the voltage according to your needs.
BP (Bypass Mode)**
A direct voltage output mode depends on the battery level; the effective coil resistance range is from 0.150 to 50.
*SP (Super Player Mode)
In DIY mode, when the coil resistance of the loaded coil is between 0.03-0.050, the system will prompt to enter the super player mode, which is suitable for the RDA/RBA coil with ultra-low resistance.

PROTECTIONS

Short-circuit Protection: When a short circuit is detected, the device will stop working and show “SHORT ATOMIZER” on the screen.
Resistance Protection: When a low resistance is detected, the device will stop working and show “LOW ATOMIZER” on the screen. When a high resistance is detected, the device will stop working and show “HIGH ATOMIZER” on the screen.
No Load Protection: When the device cannot detect the coils, the device will stop working and show “CHECK ATOMIZER” on the screen.
Low Voltage Protection: When the battery working voltage is extremely low, the device cannot be operated, and “LOW BATTERY” will be shown on the screen.
Over Voltage Protection: The main MCU keeps monitoring the output voltage to ensure it does not exceed the rate If it does, the device will stop working.
Overcharge Protection: When the battery is fully charged, the device will stop charging and show “100%” on the screen.
Over-discharge Protection: When the voltage drops to a low value, the device will stop working.
Overtime Protection: The device will stop working if you vape for more than 10 seconds at a time, and “TIME OVER” will show on the screen.
USB High Voltage Input Protection: When the USB port detects an input voltage exceeding the rated voltage, the device will stop charging.

CAUTIONS

Please turn off the device when it is not in use.
Do not leave the charging device unattended.
Do not drop, throw or abuse your device, which may cause
Please use a standard USB output charger with a proper charging current and voltage range.
Keep away from the water or any flammable gas, or liquid.
Do not expose the device to direct sunlight, dust, moisture, or mechanical shock.
Do not expose the device to extreme temperatures. (Recommended temperature range: -10-60°C /14-140 F while using and -10-45°C /14-113 F while storing).
EEE Recycling: The product should not be treated as household waste, instead, it should be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
Battery Recycling: The product battery should not be treated as household waste, instead, it should be handed over to the application used battery collection point for recycling.
Only have your device repaired by Vaporesso. Do not attempt to repair it by yourself as damage or personal injury may occur.

WARNINGS
This refillable electronic cigarette is intended for use with compatible e-liquid, which may contain nicotine. Nicotine is an addictive substance and it is not suitable or recommended to use in the following cases:

This device is not suitable for:
– Persons under the legal smoking age.
– Persons experiencing heart disease, stomach or duodenal ulcers, liver or kidney problems, long-term throat disease, or difficulty breathing due to bronchitis, emphysema, or asthma.
– Persons with an overactive thyroid gland or experiencing phaeochromocytoma (a tumor of the adrenal gland that can affect blood pressure).
– Persons taking certain medications like Theophylline, Ropinirole or Clozapine and etc.
This device is not recommended for:
– Non-smokers
– Pregnant or breastfeeding women
You may experience the following results if you use nicotine-containing e-liquid with this product. If it happens, please consult a healthcare professional and show them this leaflet if possible:
– Feeling faint – Nausea – Dizziness – Headache
– Coughing – Irritation of the mouth or throat
– Stomach discomfort – Hiccups
– Nasal congestion – Vomition
– Chest palpitations/pain or an irregular heart rate