EUROM 334890 Golden 1500 Slim Instruction Manual

EUROM -334890 -Golden -1500 -Slim

Explanation of symbols

The Golden Slim infrared heater is equipped with a rotatable wall bracket so that it can be used horizontally or vertically. This deserves special attention when installing the appliance, because you must take into account the minimal distances from the wall, ceiling and ground in all the optional positions:
The housing, especially the front side of the appliance, becomes extremely hot. For safety reasons, when mounting the Golden Slim infrared heater on a wall (both in horizontal and vertical position), always make sure that the lowest heat point of the protective grid is at least 180 cm from the ground.
This means that if you want to use the infrared heater in both horizontal and vertical position, the holes that you drill for the wall bracket must be at a distance of at least 210 cm (for the Golden Slim 1500) and 220 cm (for the Golden Slim 2000). Make sure that – when mounting the infrared heater – the distance to the ceiling must be at least 25 cm under all circumstances – both for vertical and horizontal use. The minimal distance to any side walls is 50 cm. Make sure that the infrared heater is always directed downwards and never towards the ceiling to prevent overheating of the ceiling.

Production description

This infrared patio heater is energy-efficient, environmentally-friendly and is very suitable for outdoor use. In addition, this infrared heater has a high degree of water-tightness (IP65, completely dust & spray-water tight). Use the infrared heater only for what it was designed to do: heating a patio or an area with a canopy. The infrared patio heater has a separate electric part with a receiving point for a remote control and an On/Off switch at the rear side. Carefully read the safety regulations, the instructions for mounting and operating before you install or operate the infrared patio heater. Any change made to the infrared patio heater can have consequences for safety and the warranty.

Technical data

Safety Warnings

Warnings for installation

1. In the event of incorrect usage or installation, there is a risk of electric shocks and/or a fire hazard.
2. The casing, particularly the front of the device, will get extremely hot, up to 360°C. For safety reasons, the lowest hottest point of the device must always remain at least 180 cm above the ground, secured to the wall.
3. The ceiling or the wall to which the device is mounted must not be made of flammable materials. It must be resistant to temperatures of at least 150°C without burning, melting, deforming or bursting into flames. Check regularly to ensure that the walls and ceiling are not overheating; this could be dangerous! For wall mounting (in all positions): maintain a minimum distance to all side walls of 50 cm and ceilings of 25 cm.
4. Make sure that the infrared heater is always directed downwards and never towards the ceiling to prevent overheating of the ceiling.
5. Before use, check to ensure that the voltage, as indicated on the device, corresponds with the voltage from the electrical point to which it will be connected. The power supply and connection must fulfil the valid, legal standards and national regulations. Only use an undamaged, earthed socket that is protected with a 30 mA earth leakage circuit breaker.
6. When you are using the unit outside, it must be connected to a suitable, waterproof, earthed socket. All electrical connections must remain dry under all conditions. Neither supplier, importer nor manufacturer is liable for incorrect connections!
7. Do not locate the device directly under, above or in front of an electrical socket.
8. When choosing the location of the device, make sure it is out of the reach of children. Make sure that they cannot play with the device.
9. Ensure that the electric cable does not hang off sharp edges, is not twisted around sharp corners, cannot be dragged along and does not come into contact with any hot surfaces. Roll the electrical cable out fully before you insert the plug into the socket. Do not place the cable under carpet, cover with mats, runners or similar and do not place in areas that are walked on frequently. Ensure that it cannot be stepped on and that no (garden) furniture is placed on top of it. Do not bend the cable around sharp corners and do not roll up too tightly after use.
10. Keep all flammable objects, such as (garden) furniture, curtains, clothing, paper, etc. and also electrical cables out of the vicinity of the device (at least one metre)!
11. If you are using the device outdoors, stow tent cloth/plastic etc. or ensure there is additional distance between this type of material and the heater.
12. Never place the unit above or within one metre of a tap or other source of water. Do not install the device in a damp environment, such as a bathroom, washing area or similar indoor environment. Despite the fact that the device is splash-proof, you must be careful with water. Make sure that the device cannot fall into water and never expose it to water jets. Do no operate or touch the device with wet hands. Install the device so that it cannot be operated or touched from a swimming pool, bath or shower.
13. The use of an extension cable or junction box is not advised as this can lead to overheating and fire. If the use of an extension cable is unavoidable, make sure that it is not damaged and that it is an approved extension cable with a minimum diameter of 3×2.5 mm².
14. The electrical capacity of the extension cable and/or junction box must be more than adequate for the device to be connected and the voltage for which the extension cable and/or junction box is intended must correspond with the requirements of the device. Extension cables and junction boxes must fulfil statutory regulations.
15. Always fully extend the (extension) cable in order to prevent overheating!
16. Only use the device if it has been properly secured to a wall or ceiling. Make sure that you always use attachment materials that are suitable for the surface you are working with; consult an expert if required.
17. Never make any changes to the device, electrical cable or plug.
18.  If this device is directly connected to the cabling of your electricity installation, it must be installed by a competent specialist, taking account of the valid laws and regulations and the instructions.

Warnings for use

1. Never cover or block the device; it will overheat and this could lead to a fire risk. Never hang or place objects such as clothing, blankets, cushions, paper, etc. on the device. The minimum distance of 1 metre between the device and flammable materials must always be applied.
2. The casing, particularly the front of the device, will get incredibly hot during use. Never touch the device when it is on or shortly thereafter; it could burn you! Make sure that the wind or other environmental factors do not move any flammable materials into the immediate vicinity of the device. This could include curtains, tent canvas, flags, plastic film, etc. This could lead to burns or fire. Make sure that they do not cover or block the device.
3. Do not store any flammable liquids or materials, such as paint, petrol, gas bottles, etc. in the immediate vicinity of the device. Do not use the device in an environment that poses a fire risk, e.g. near gas tanks, gas pipes or aerosols. This is an explosion and fire risk!
4. Never pull on the cable to remove the plug from the socket or to move the unit.
5. Never stick fingers or pencils or any other objects into an opening in the device.
6. Prevent the cable coming into contact with the device, oil, solvents and sharp objects or becoming hot. Unroll the cable in full before using the device. Check the cable regularly for damage.
7. Remove the plug from the socket if you do not plan to use the unit for an extended period.
8. Warning! Some parts of this device will get very hot and could cause burns. You must pay particular attention to children, vulnerable persons and pets that are present near the device.
9. Make sure there is close supervision if this device is used when there are children, incapacitated person or pets present. Never leave them alone with a working device.
10. Children younger than 3 must be kept out of the vicinity of the device unless they are continuously supervised.
11. Children aged between 3 and 8 may only switch the device on and off if the device is installed at its usual workplace and they are under supervision or if they have received suitable instructions regarding safe methods for using the device and understand the corresponding dangers. Children between the ages of 3 and 8 may not insert the plug into the socket, adjust the device settings or clean or maintain it.
12.  This device is not suitable to be operated by children or those with physical, sensory or mental disabilities or by anyone who does not have knowledge about or experience with the device. The device may be used by children aged 8 or above and persons with reduced physical capacities, sensual or mental skills or a lack of experience and knowledge if they are under supervision or if they have received suitable instructions regarding safe methods for using the device and understand the corresponding dangers.
13. Warning! This device is not equipped to monitor the ambient temperature in the room. Do not use the device in small rooms if these rooms are used by persons who are not capable of leaving the room independently, unless there is constant supervision.
14. Warning! Never leave the device unattended if it is turned on. Do not use a programmer, timer or other facility that turns the device on automatically. Never use the device with an external voltage regulator such as a dimmer or similar, as this could be dangerous!

Warnings for maintenance

1. Always keep the unit clean and free from dust.
2. Switch the device off and remove the plug from the socket if:
3. the device is damaged or has fallen over
4. the device creaks or cracks or works intermittently
5. you notice deficiencies or breakdowns when it’s in use
6. the casing, the front, the electrical cable or plug are damaged in any way This could create a fire risk or a risk of injury or damage.
7. If the device, electrical cable or plug show signs of damage or breakages, consult your supplier, the manufacturer or an authorised service point for repairs or replacement. Do not carry out your own repairs as this could be dangerous! Repairs, carried out by unauthorised persons or changes to the device could damage the dust/waterproof capacity of the device and will nullify the guarantee and the manufacturer’s liability.
8. Always turn the device off, remove the plug from the socket and leave to cool down before you touch it, install it, move it, clean it or carry out any maintenance.

Description

The infrared patio heater consists of 3 parts

• heater with an electric cable, plug and mounting bracket;
• wall support with attachment materials;
• remote control.

After opening the packaging, check immediately whether the delivered contents are complete and in perfect order. Contact your supplier if the product delivered is incomplete or has faults. Do not use the infrared patio heater if it is defective. Save the original packaging during the lifespan of the infrared patio heater in a safe place, out of reach of children. Use the packaging for storage and transport. Dispose of the packaging only after the lifespan of the infrared patio heater has expired.

Installing and attaching

• The wall on which the appliance will be mounted and the ceiling above it must be made of non-flammable material or material that is hardly flammable. In any case, it must be able to withstand a temperature of at least 150°C without scorching, melting, warping or catching flames. Check regularly whether the wall and ceiling are not overheated; this can be dangerous!
• Prior to mounting, minimal safe mounting distances and tilting angles must be observed (as shown in the illustrations below).
• When mounting the heater on a wall (both in horizontal and vertical position), always make sure that the lowest heat point of the protective grid is at least 180 cm from the ground. This means that if you want to use the infrared heater in either horizontal or vertical position, the holes that you drill for the wall bracket must be at a distance of at least 210 cm (for the Golden Slim 1500) and 220 cm (for the Golden Slim 2000).
• Make sure that when mounting the infrared heater, the distance to the ceiling must be at least 25 cm under all circumstances – both for vertical and horizontal use.
• The distance between the infrared heater and the side walls or something similar must be at least 50 cm.
•  The recommended downwards tilting angle is 45° (see illustration). The infrared heater must never be directed to the ceiling to prevent overheating of the ceiling.
• Make sure that the infrared patio heater never hangs in a place with powerful wind.
• Determine the place of the wall bracket; the wall bracket must be affixed horizontally to the wall. Position the wall bracket in such a way that when mounting the infrared heater to the wall bracket, you maintain the minimal distances provided by the drawings above. Make sure that the wall bracket and the infrared heater are installed with the correct side facing upwards (see labels “This side up” on the wall bracket and the infrared heater). Therefore, the wall bracket is mounted on the underground with its shorter side directed upwards (see illustration).
• Now mark the 3 places where the holes should be drilled.
• Drill the holes (10 mm) on the places marked and place the 3 bolts / cotter bolts in the holes. Cotter bolts are suitable mainly for concrete and stone walls. For other surfaces, use fasteners that are suitable for the surface: Consult an expert, if necessary.
• Screw the wall bracket firmly to the wall.
• Make sure that the installation place is safe and sturdy.
• Now attach the infrared heater to the wall bracket. First use the Allen key delivered with the package to unscrew the socket screw from the wall bracket (1) and pull the pin that has the other socket screw from the wall bracket (2). Install the support bracket of the infrared heater on the wall bracket. Push the pin that has the socket screw back into the holes in the wall bracket. Also install the first socket screw and tighten it using the Allen key (3).
• Now adjust the desired radiation angle and tighten the socket screw firmly. Check regularly whether all the screw connections are still attached firmly. As a result of mechanical pressure and oscillation by wind or rain, the infrared patio heater could dislodge.
• Remove both foam strips from the protective grid of the infrared heater. These foam strips are meant to protect the lamp during transport.
• For personal safety, the infrared patio heater must be connected to an electric system, which is protected by an earth leakage switch of maximum 30mAmp. Use only an undamaged, earthed socket outlet (for outdoor use, a water-tight socket outlet).
• Under certain circumstances, it might be worthwhile to connect the infrared patio heater permanently to the electric grid and to operate it with a switch. To guarantee the safety and dust & water tightness of the infrared patio heater, a certified electrician must carry out this type of connection.

Putting into operation and control

• Check before each use:
  • whether the infrared patio heater is not damaged;
  • whether the infrared patio heater is still attached firmly;
  • whether no objects, tarps, parasols, etc. are located within the indicated safety distance;

whether the socket has the correct voltage (220-240V~50Hz) and that it is earthed.

• If everything is in order, you may put the plug into the socket.
• To be certain that the infrared patio heater is operating without any problems, observe the appliance closely for the first 10 to 15 minutes during first time use (and again after a long period of not using it).
• The infrared patio heater has a remote control that is operated by two AAA 1.5V batteries. During use, point the remote control to the receiving point of the infrared patio heater (on the electric part). Make sure that there are no obstacles in between the remote control and the infrared patio heater. Remove the batteries during off-season. That will give the remote control a longer life.
• Press the On/Off switch at the rear side of the infrared patio heater on ‘I’ (On).
• Operating with a remote control

Warning: If the infrared patio heater is switched off only by means of the remote control, it stays on ‘stand by’. Therefore, always switch off the infrared patio heater using both remote control, the on/off switch and take the plug out of the socket.

Cleaning, maintenance and service

Cleaning
This infrared patio heater consists of a sturdy and maintenance-free aluminium housing with a protective grid for the lamp. Before you clean the outside of the heater, always take the plug out of the socket and let the lamp cool down. Clean the infrared patio heater with a clean, soft, lint-free cloth or a soft brush. Do not use any aggressive cleaning agents, scouring sponges or abrasive brushes and no chemical cleaning agents; these can damage the material. In addition, never use flammable cleaning materials, such as benzene or alcohol. Let the infrared patio heater dry well before using it again. Never immerse the plug, electric cable or any other part of the infrared patio heater in water or in any other liquid. That could result in an electric shock.
Maintenance
There are no parts in the infrared patio heater that require maintenance or that can be replaced/repaired by the user. The appliance is extremely watertight (IP65, watertight against spray) and therefore, may not be opened by unqualified persons. The lamp is of very high quality. Its potential lifespan is 8,000 burning hours and in case of normal use, there is no need to replace it. Very intensive use could accelerate its aging and of course it could break as a result of an accident. In such a case, turn to your supplier or a certified electrician. The lamp has a special connection and may not be removed or replaced by an unauthorised person.
Service
Any repairs must be done by specialists trained for that purpose (supplier or certified electrician) in order to guarantee safety. Any damage or malfunctioning as a result of repairs carried out on or changes made to the appliance by unqualified persons, or as a result of accidents, misuse, negligence, incorrect/insufficient maintenance and commercial use may invalidate the warranty. The manufacturer works constantly to improve his products. Therefore, the manufacturer reserves the right to make changes in the product or documentations without any notifications.

Removal

In the EU this symbol indicates that this product may not be disposed of as ordinary household waste. Old equipment contains valuable materials, suitable for recycling. These materials should be made suitable for reuse in order to prevent any adverse effects to health and the environment caused by unregulated waste collection. Therefore, please make sure that you bring old equipment to a designated collection point. Alternatively, contact the original supplier, who can make sure that as many of the components as possible can be recycled.

CE-declaration
The undersigned Eurom, Kokosstraat 20, 8281 JC Genemuiden – NL declares that the infrared heaters known under the brand: EUROM, types EUROM Golden 1500 Slim/Eurom Golden 2000 Slim fulfils the requirements of the norms below: LVD 2014/35/EU: EN 60335-1:2012+A11:2014+A13:2017 EN 60335-2-30:2009+A11:2012 EN 62233:2008 RoHS 2011/65/EU&(EU)2015/863 Genemuiden, 22-12-2020 W.J. Bakker, alg. dir.

• EMC 2014/30/EU:
• EN 55014-1:2017
• EN 55014-2:2018
• EN 61000-3-2:2014
• EN 61000-3-3:2013

References

• Eurom - Powerful products - producten voor comfort en gemak

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>