anslut 417013 400W IP24 Frost Guard Instruction Manual

anslut 417013 400W IP24 Frost Guard

SAFETY INSTRUCTIONS

Read these instructions carefully before use!

• This appliance can be used by children aged from 8 years and above and people with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
• Keep the appliance and its cord out of reach of children less than 8 years.
• WARNING : Certain parts of the appliance can become extremely hot and cause burns. Special attention must be given when children and people with reduced physical, sensory or mental capabilities are present.The convector heater with thermostat is designed for use in the home or similar purposes. The heater may only be used as a fixed installation and only for its intended purpose.
• Do not use the appliance outdoors.
• The heater must be mounted on a wall. Never use the heater as a portable unit.
• Check that the mains voltage corresponds with the data on the appliance’s type plate, and that the mains outlet is earthed or grounded.
• Keep the power cord away from the heater when it is hot.
• Do not use the appliance outdoors.
• Do not cover or obstruct the heat outlet grilles or the air intake openings.
• Never place the heater on soft carpets or other soft surfaces.
• The heater must be placed on a firm, level surface.
• Do not place the heater close to curtains or furniture. Fire hazard.
• Do not place the heater in front of or close to power sockets.
• Do not insert any objects into the heat outlet grilles or the air intake openings.
• Do not use the heater in the vicinity of flammable liquids or gases.
• Pay extra attention when the heater is used in the presence of children or people with disabilities.
• Unplug the power cord before moving the heater.
• Do not use the appliance if the power cord is damaged.
• A damaged cord must be replaced by an authorised service centre.
• See the instructions below for replacement of a damaged plug.
• Only use a 220–240 V power socket.
• There must be no highly flammable substances in the same room as the heater, e.g. petrol, solvents, spray canisters or other easily combustible materials such as wood or paper. Fire hazard!
• The appliance is not intended to be used by persons (children or adults) with any form of functional disorder or by persons who do not have sufficient experience or know-how on how to use it, in so far as they have not received instructions concerning the use of the appliance from someone who is responsible for their safety.
• Children must be supervised to make sure they do not play with the appliance.

TECHNICAL DATA

• Rated voltage 230 V ~ 50 Hz
• Output 400 W
• Protection rating IP24

INSTALLATION

The figures in the text refer to the illustrations. Keep to the specified minimum distances. Fix the mounting bracket to the wall (see figure). Two mounting screws and plugs are included for installation. Drill holes into the wall. Push the plugs in and screw the bracket in place. Make sure the bracket is vertical. Remove the safety screw and take out the mounting lever. Re-fit the safety screw and hook the mounting lever onto the bracket to hang up the heater. Plug in the power cord. The heater is ready for use. The heater must not be connected permanently to the mains power supply.

OPERATION

NOTE!
When the heater is turned on for the first time, or after a long period of storage, it is normal for it to produce odour and fumes. These disappear after a few moments of operation.

Description
This unit is an electrical convector heater. It is fitted with a thermostat to ensure correct temperatures and to protect against overheating. A control lamp comes on when the heater starts to heat up. The thermostat switches the heater on and off to maintain the room at the set temperature. The built-in overheat protection switches the heater off if it gets too hot and automatically switches it on again when it has cooled down. The heater is always ready for use. Turn off the heater by unplugging the cord.

Use
The temperature knob and the marking on the casing show the setting of the thermostat.

Frost protection setting (approx. 5°C)

Setting the required room temperature
Turn the knob clockwise as far as possible. Wait until the required temperature has been reached. Slowly turn the knob back until the control lamp goes out. The position of the knob now corresponds to the temperature required.

MAINTENANCE

• Unplug the power cord and allow the appliance to cool before cleaning.
• Clean the casing with a damp cloth and then wipe with a dry cloth.
• Do not use any detergents or abrasives.
• Never allow water to enter the heater.

Storage

Store the heater in a dust-free, dry area if it is not going to be used for some time.

References

• Jula – products for home and garden

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>