Reliance Communications QSIP7180 Wireless Module Instructions

Reliance Communications QSIP7180 Wireless

QSIP7180 Module Instruction Document

Reliance Communications LLC 91 Colin Drive, Unit 1, HOLBROOK, New York 11741, United States

The QSIP7180 has two baseline regulatory certification variants:

• Windows or Chromebook for WWAN + Wi-Fi/BT
• Regulatory Model: QSIP7180

FCC ID: 2ABGH-RC116LCB

Note: This module will not be sold separately, this file is only for FCC applications.

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.

CAUTION:

Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment. This device is slave equipment, the device is not radar detection and not ad-hoc operation in the DFS band. This module is intended for OEM integrator. The OEM integrator is responsible for the compliance to all the rules that apply to the product into which this certified RF module is integrated. Additional testing and certification may be necessary when multiple modules are used.

USERS MANUAL OF THE END PRODUCT:

In the user’s manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio- frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate this equipment. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.

LABEL OF THE END PRODUCT

The final end product must be labeled in a visible area with the following” Contains FCC ID: 2ABGH-RC116LCB”. 47CFR Rules Parts Addressed in Modular Certification

This FCC ID: WL6-718020QT1C has been approved by FCC to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. The module is certified for use only with certain antennas described in this chapter.

For 4GHz/5GHz unlicensed band: Allowed antenna type:

Note: The antenna connector is I-PEX type. For WWAN licensed bands:

Allowed maximum gain (dBi), including antenna cable loss

Band|

US FCC

---|---
Antenna Gain (dBi)
2: US| 5
4: US| 5.8
5: US| 2.1
7: US| 5.4
12:US| 0.9
13:US| 1.3
14:US| 1.8
17:US| 0.9
25:US| 5.1
26:US| 2.1
30:US| 0
66:US| 5.9
71:US| 1.1
38:US| 5.2

Integrated Product Test and CertificationRequirements

Integrators must adhere to test guidance provided in FCC KDB 996369 D04 available at this website: https://apps.fcc.gov/oetcf/kdb/forms/FTSSearchResultPage.cfm?switch=P&id=446 37

1. The module has been approved for the rule parts defined in Table 4-1. Host device must be tested for Part15B compliance
2. Radiated emissions testing should be tested per KDB 996369 with all transmitters active and transmitting at max transmit power. A ECS account representative can assist with making test tools available as needed.
3. The recommended method of test is to use a call box simulator for WWAN where the UE is configured for maximum transmit power. For WLAN testing, if an access point is not available for mission mode testing, Qualcomm test tools can be used to configure the WLAN modem for maximum transmit power and the desired mode/frequency of operation.
4. If a memory variant is utilized, limited WWAN and Wi-Fi transmitter testing should be completed to ensure equivalent compliance The following testing must be completed at a minimum
   • Limited unlicensed band edge measurement and unwanted radiated spurious emissions
   • Radiated emissions in FCC Part 15.205 restricted bands during Wi-Fi and BT operation
   • Limited WWAN radiated emissions
   • Part 15B testing

NOTE: Data can be leveraged from the part of Part 15B and radiated emissions referenced above to address continued compliance with the variant memory.

5. RF Exposure must be addressed at the host level for all “portable” products where users in accordance with FCC KDB 447498. Host product manufacturers must provide all required documentation to the end-user.

6. Antennas must follow the guidelines defined in Section 7.

7. In the US, either a Class II Permissive Change or new equipment authorization is required.Data can be leveraged from FCC ID: 2ABGH-RC116LCB per FCC KDB484596.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>