kogan KASTKSTM05A 5-In-1 Steam Stick User Guide

: June 5, 2024
: Kogan

Table of Contents

kogan KASTKSTM05A 5-In-1 Steam Stick
SAFETY & WARNINGS
OVERVIEW
OPERATION
Removing and Filling the Water Tank
CLEANING & CARE
SPECIFICATIONS
TROUBLESHOOTING
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

kogan KASTKSTM05A 5-In-1 Steam Stick

SAFETY & WARNINGS

Do not share the same power supply with other high-power appliances.
Do not use in conjunction with any extension cords.
Use the unit only as described in this guide.
Do not immerse the unit, its power cord or any accessories in water or other liquid.
Place the mop pad on the bottom of the mop head before use. The mop pad is used to wipe the floor and helps protect the floor. The mop pad can be washed and reused.
When finished cleaning, turn the steam off to prevent damage to the floor.
Do not use any detergent or chemicals in the tank.
When adding water, you must turn off the power switch and unplug the unit first.
Do not place the power cord close to any hot surfaces or sources of heat.
Do not touch the nozzle part while the unit is in use.
Do not spray steam onto devices that contain electrical components.
Do not allow children or anyone unfamiliar with the appliance to use the unit.
The maximum amount of water added to the appliance is 250ml. When adding water, pay attention to the cover buckle and avoid spills.
Do no attempt to repair the product yourself. If you experience any fault or damage, cease using it immediately and contact helpKogan.com for support.
Unplug the appliance before performing any maintenance or cleaning.

OVERVIEW

kogan-KASTKSTM05A-5-In-1-Steam-Stick-1

OPERATION

Jet Nozzle Installation
Align the jet nozzle with the air outlet head at the front of the main unit, then rotate it until the jet nozzle is firmly attached to the unit.
Nylon Brush Installation
Attach the small brush on the jet nozzle, ensuring the brush is installed as illustrated to the left. Otherwise, the installed brush will not work properly.
Wiper Installation
Attach the wiper to the jet nozzle.
- Plug the unit into a power outlet. The power indicator will flash as the unit heats up.
- When the indicator stops flashing and turns solid (after about 20 seconds), the unit has finished heating and you can press the steam switch button. To stop the steam, press the switch button again.
- Use the controls to adjust the steam strength as required.

Note: Ensure the steam is directed away from pets, plants or other electrical appliances.

Extension Pole Installation

Align the extension pole with the main body of the unit and then attach it by gently rotating the extension pole into the main unit. In the same way, the mop head can be connected to the extension pole and the extension pole can be connected to the Jet Nozzle.

Water shortage
It is important to pay attention to the amount of water in the tank when using the steam mop. If the water level is too low, no water will be transferred to the mop head. If the water tank is left empty, severe damage can be caused to the unit.

WARNING

To avoid overheating, please unplug the unit when not in use. The steamer will remain hot until unplugged.
If using for a long period, ensure the steamer is stopped every 10 minutes to allow the unit to cool down. Using for more than 10 minutes at a time may result in overheating and damage.

Removing and Filling the Water Tank

Note: Ensure the unit is unplugged before filling the water tank.

Press the water tank button and remove the water tank.
Pull the tank cover up and remove the tank lid.
Add water to the tank.
Note: To extend the life of the unit, distilled water is recommended. Never add any chemicals or detergent to the water tank.
Replace the water tank cover.
- Hold the water tank button and insert the water tank into the main unit.

CLEANING & CARE

Mop pad cleaning

Clean regularly to avoid the spread of dirt and bacteria.
When changing the mop pad, be careful not to touch the unit outlet with your hands to avoid burns.
To remove odour from mop pad, dissolve 2 tablespoons each of baking soda and salt into a half a litre of water and let the mop pad stand in it for half a day. Half a cup of vinegar can be used instead.
The mop pad is machine washable and should only be air dried.

Note: When removing or replacing any accessories, ensure that the unit is unplugged and no steam is being emitted. The unit needs to be cooled for 15 minutes after unplugging to avoid burns.
Main unit
Wipe with a cloth which is dry or dampened with warm water and a touch of mild detergent. Do not immerse the unit in water or other liquids.
Storage
Unplug the power cord, allow the unit to cool down and wipe it clean. Remove the mop, wrap the power cord around the mop and store it in a dry, well ventilated place.