anslut 016847 Laser Projector Instruction Manual
- June 5, 2024
- anslut
Table of Contents
Item no. 016847
LASER PROJECTOR
OPERATING INSTRUCTIONS
**** Important! Read the user instructions carefully before use. Save them
for future reference.
(Translation of the original instructions)
WARNING!
Laser product class 2 – can cause permanent eye damage.
Do not look into the laser beam.
- Do not point the laser beam at people or animals – directly or indirectly. Laser radiation can cause burn injuries or permanent damage to the cornea.
- Do not point the laser beam at roads, traffic, etc.
- Do not point the beam at airplanes or other aircraft.
- Do not allow children to play with the product and store it out of their reach of children.
- The product is intended for indoor and outdoor use.
- Always take basic safety precautions when using the product to reduce the risk of fire, electric shock, and/or personal injury.
- Read all the instructions, safety instructions, and warning labels on the product before using it.
- Do not remove the product casing. The product does not contain any parts that can be repaired by the user.
- No parts of the product can be replaced or repaired. The whole product must be discarded if any part is damaged.
- Do not expose the product to high temperatures or direct sunlight.
- Do not allow the bulbs to come into contact with the cable or other wires.
- Only use the supplied mains adapter.
- Do not fasten the cable with staples or nails etc., or hang it up on sharp hooks or nails.
- Do not hang objects on the cable.
- Make sure that the cable is not pinched in doors or windows etc. – this can result in the risk of electric shock.
- Pull out the plug when the product is not in use. Never leave the product unattended when plugged into the mains.
- The product is intended for temporary use during all seasons of the year. It is not intended for permanent installation or use.
- Never use the product for anything other than the purpose it was designed for.
- Never cover the product when in use.
WARNING!
-
Do not look directly into the laser beam. Laser radiation can cause burn injuries or permanent damage to the cornea.
-
Never modify the product in any way. The manufacturer cannot accept liability for any damage caused by unauthorized modifications.
-
This is not a toy. Make sure that children cannot use it.
-
Contains small parts – the risk of suffocation.
Symbols
WARNING:
LASER RADIATION DOES NOT LOOK INTO THE LASER BEAM
6000-3-3:2013
Wavelength: 532 nm, 650 nm
Max power output: CW<1 mW
CLASS 2 LASER PRODUCT
IMPORTANT: Laser radiation class 2 in open mode. Do not look into the
laser beam.
Do not point the beam at airplanes or other aircraft.
| Safety class II.
---|---
| Class III.
| Approved in accordance with the relevant directives.
Recycle discarded products in accordance with local regulations.
WARMING UP TIME AT COLD TEMPERATURE
NOTE: It can take up to 10 minutes for the product to warm up when it is
cold.
TECHNICAL DATA
| Rated voltage | 230 V ~ 50 Hz/5 V |
|---|---|
| Output | 5 W |
| Safety class, transformer | II |
| Protection rating | IP44 |
| Laser wavelength | 532/650 nm |
| Output | <1 mW |
| Twilight sensor | Yes |
| Ambient temperature | -20 – +35°C |
| Coverage | 280 m² |
DESCRIPTION
- Power switch
- Adjust knob
- Ground spike
- Twilight sensor
- Projector lens
FIG. 1
ASSEMBLY
- Remove all the parts from the packaging.
- Fit the laser light on the ground spike.
- Press the ground spike firmly in the ground so that the laser light is stable.
- Undo the adjusting knob, set the required angle, and tighten.
- Connect the transformer to the mains.
HOW TO USE
WARNING!
- Do not look directly into the laser beam.
- Laser radiation can cause burn injuries or permanent damage to the cornea.
- Adjust the laser light to shine on the required surface. There is a better effect if the light is projected onto a dark surface.
- Plugin the plug and press the power switch.
- By pressing the switch as follows nine different light options are activated:
Number of times| Options
---|---
Once| Red and green rotating light.
Twice| Red rotating light.
3 times| Green rotating light.
4 times| Alternating red and green flashing lights.
5 times| Red and green rotating and flashing light.
6 times| Red and green rotating and flashing light (fast).
7 times| Red and green steady light.
8 times| Red light.
9 times| Greenlight.
10 times| OFF. - The laser light remains on until switched off manually, or until the twilight, sensor switches it off when it gets lighter.
If switched off by the twilight sensor it will also switch on when it gets darker.
MAINTENANCE
- Check the laser light before use. Do not use the laser light if the cable or plug is damaged, or if the casing is cracked or damaged.
- Be careful when taking in the laser light after use, so that none of the parts fasten in branches or are subjected to stress or damage.
- Store the laser light in a cool and dry place when not in use, and protected it from direct sunlight.
- Clean with a soft, dry cloth.
TROUBLESHOOTING
| Problem | Possible cause | Action |
|---|---|---|
| No light. | No power supply. | Check that the plug is plugged in and that the |
PowerPoint is supplied with voltage.
The laser light needs to be reset.| Switch off and start the laser light with
the power switch.
The projection surface is too dark, or the surrounding light is too bright.|
The best light effect is on a dark surface in the dark.
The laser light is not correctly aligned.| Point the laser light at the
projection surface.
The laser light tips over, or leans.| The laser light is not correctly mounted
on the ground spike.| Adjust the laser light to the required position and
tighten the knob.
The laser light is not properly anchored.| Anchor the laser light better.
Care for the environment!
Must not be discarded with household waste! This product contains electrical
or electronic components that should be recycled. Leave the product for
recycling at the designated station e.g. the local authority’s recycling
station.
Jula reserves the right to make changes. In the event of problems, please
contact our customer service. www.jula.com
Tillverkare/Produsent/Producenci/Manufacturer
Jula AB, Box 363, 532 24 SKARA
Distributor
Jula Poland Sp. z o.o., ul.
Malborska 49, 03-286 Warszawa, Polska
Jula Norge AS, Solheimsveien 30,
1473 LØRENSKOG
2021-08-02
© Jula AB
EU DECLARATION OF CONFORMITY
Jula AB, Box 363, SE-532 24 SKARA, SWEDEN
This declaration of conformity is issued under the sole responsibility of the
manufacturer
LASER RED+GREEN IP44
Item number: 016847
Conforms to the following directives, regulations, and standards
Low Voltage Directive 2014/35/EU
60598-2-4:2018, EN 60598-1:2015+A1:2018, EN 62493:2015, EN 60825-1:2014
Electromagnetic Compatibility 2014/30/EU
55015:2019+A11:2020, EN 61547:2009, EN 61000-3-2:2014, EN 61000-3-3:2013
+A1:2019
RoHS Directive 2011/65/EU and (EU) 2015/863
0581:2012
This product was CE marked in the year -21
Skara 2021-04-21
Fredrik Bohman
BUSINESS AREA MANAGER
References
- Jula – products for home and garden
- Jula - ingenting kan stoppe deg nå!
- Jula - Teraz nic Cię nie powstrzyma!
- Jula – inget kan stoppa dig nu!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>