WARING TBB145 Torq 2.0 2-HP Blender with Toggle Switch Instruction Manual

: June 5, 2024
: WARING

Table of Contents

WARING TBB145 Torq 2.0 2-HP Blender with Toggle Switch
IMPORTANT SAFEGUARDS
SAVE THESE INSTRUCTIONS
**PARTS & ASSEMBLY
OPERATING INSTRUCTIONS
IMPORTANT
WARRANTY
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

WARING TBB145 Torq 2.0 2-HP Blender with Toggle Switch

WARING-TBB145-Torq-2.0-2-HP-Blender-with-Toggle-Switch-
pro

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be taken, including the following:

READ ALL INSTRUCTIONS.2.
Unplug from outlet when not in use, before putting on or taking off parts, and before cleaning
To protect against electrical hazards, do not immerse the blender base in water or other liquid.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety
Children should be supervised to ensure that they do not play with the
Avoid contact with moving
Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or is dropped or damaged in any manner. Return appliance to the nearest authorized service facility for examination, repair or electrical or mechanical adjustment.
The use of attachments not recommended by the appliance manufacturer may cause hazards.
Do not use outdoors.
Do not let cord hang over edge of table or counter, where it can inadvertently be pulled on or tripped over or touch hot surfaces, which could damage the cord.
Keep hands and utensils out of container while blending to prevent the possibility of severe personal injury and/or damage to the blender. A rubber scraper may be used, but must be used only when the blender is not running.
Blades are sharp. Handle
Never place cutting assembly or cutting blades on base without container properly
Always operate blender with cover in
Always operate blender with jar pad in
CAUTION: This blender is not intended for use with hot liquids or ingredients.
Do not fill above MAX FILL line for
Not for waterjet
Ensure the jar coupler and motor coupler are aligned and engaged before operating. If unable to engage, remove jar and shake contents, then try
The jar coupler and motor coupler may be hot after running; do not touch.
Replace jar pad if worn.
Always use HIGH speed for crushing
If the jar overflows during blending, there is too much liquid/ingredients in the Stop blending, remove enough liquid/ingredients to below MAX FILL line, and continue blending. Do not operate if overflowing.
DO NOT use carbonated liquids in the blender jar or any blending container. Using carbonated liquids in the blender jar or any blending container may result in
DO NOT blend oil or oil-based products such as peanut butter for more than 5
Never remove blender jar from base unit until the blade and coupling have completely
CAUTION: In order to avoid a hazard due to inadvertent resetting of the thermal cutout, this appliance must not be supplied through an external switching device, such as a timer, or connected to a circuit that is regularly switched on and off by the3

SAVE THESE INSTRUCTIONS

GROUNDING INSTRUCTIONS

For your protection, Waring® Commercial Blenders are equipped with a 3-conductor cord set.
120 volt units are supplied with a molded 3-prong grounding-type plug and should be used in combination with a properly connected grounding-type outlet, as shown in Figure 1.

If a grounding-type outlet is not available, an adapter, shown in Figure 2, may be obtained to enable a 2-slot wall outlet to be used with a 3-prong plug . WARING-TBB145-Torq-2.0-2-HP-Blender-with-Toggle-
Switch-1

CAUTION: Before using an adapter, it must be determined that the outlet cover plate screw is properly grounded. If in doubt, consult a licensed electrician. Never use an adapter unless you are sure it is properly grounded.
NOTE: The use of an adapter is not permitted in Canada.

BLENDER SPECIFICATIONS

Capacity: 48 oz. Working Capacity
Rating: 220-240 Volts, 60 Hz, 13.0 Amps
Base Material: Polycarbonate
Bearing: High-Precision Ball Bearing
Cord: 6-Foot, Three-Conductor Ground Cord with Strain Relief in Base
Overall Height: 17 Inches
cULus, NSF Listed
Operating Cycle: 1 min. ON/3 min. OFF
Controls: TBB145 / TBB160 – LO 20,500, HI 24,000, PULSE 24,000 TBB175 – Variable speed dial from 1,000 to 17,000 RPM with Pulse, 24,000 RPM

**PARTS & ASSEMBLY

WARING-TBB145-Torq-2.0-2-HP-Blender-with-Toggle-
Switch-2 **

A. Base
B. Jar Pad
C. Container
48 oz., BPA-free copolyester container.
D. Lid
Center part of the two-piece lid is removable for adding ingredients.
E. Blade
Stainless steel cutting blades.
F. Operating Light
Lighted LED indicates that the unit is in standby mode. LED will blink during operation.
G. Power Cord (not shown)

Control Panel Variations

T BB145 – Toggle Switch Controls with HI, LO, OFF & PULSE
T BB160 – Electronic Touchpad Controls with HI, LO, STOP, PULSE & 60-Second Timer LED with Up & Down
T BB175 – Variable Speed Control Dial & PULSE
P ULSE Button Feature: PULSE overrides HI speed for a quick burst of power.

BEFORE FIRST USE
After unpacking, follow the Cleaning and Sanitizing Instructions on page 9 before first use and if you have not used your blender for a period of time. Thoroughly dry the container before placing it on the base.

OPERATING INSTRUCTIONS

TBB145 – Toggle Switch Controls

With the blender unplugged and in the OFF position, place the container on the blender base. Be sure container is fully seated and that the drive coupling is properly engaged.
Plug the power cord into an outlet and the LED operating light will illuminate.
Put ingredients into the container and place the lid on Do not fill above MAX FILL line.
This blender has 2 speed settings: HI and Switch toggle switch to desired position. Always use HI or PULSE for crushing ice.
When blending is complete, set toggle switch to OFF position.
This blender is equipped with a PULSE option. Hold toggle switch in down position to engage PULSE function. Unit will run on MAX speed until the toggle switch is
Allow motor to come to a complete stop before removing the container from blender base. Never place the container on the motor base or remove it from the motor base while motor is running.
Always hold container with one hand when starting and while blending. Never operate without
Wash and dry the container after each use. See Cleaning and Sanitizing Instructions.
Unplug to turn off all power to

TBB160 – Electronic Touchpad Controls with Timer

Follow steps 1–3 from the TBB145 operating instructions.

This blender is equipped with variable Speed Control Dialthat operates from speeds 1–10 and POWER, START/STOP and PULSE buttons. Always use Speed 10 or PULSE for crushing ice.
For continuous blending, turn the variable speed control dial clockwise to set the speed from 1–10. Press the START/STOP button to start blending. The LED will blink during blending. When blending is complete, press the START/STOP button to stop blending. You may wish to start at a low speed and increase to a higher setting.
For momentary operation, press the PULSE button; motor will run on MAX speed until the button is released.
Allow motor to come to a complete stop before removing container from blender base. Never place the container on the motor base or remove it from the motor base while motor is running.
Always hold container with one hand when starting and while blending. Never operate without
Wash and dry the container after each use. See Cleaning and Sanitizing Instructions.
Unplug to turn off all power to

RESETTING THERMAL PROTECTION

Your blender is equipped with a manual reset switch to protect the motor from overheating.
I f your blender stops running under heavy use, or if the LED light starts to blink much more rapidly than usual during normal blending, press the power switch to OFF and unplug the power cord. Empty the blender container of all its contents and allow approximately 5 to 10 minutes for the motor to cool down.
Plug the power cord back into the outlet and continue blending.
I f your blender does not function properly following this procedure, discontinue use and contact a certified Waring Customer Service Center.

CLEANING AND SANITIZING INSTRUCTIONS

THE CONTAINER MUST BE CLEANED AND DRIED AFTER EACH USE OF THE BLENDER ACCORDING TO THE FOLLOWING INSTRUCTIONS.
FAILURE TO DO SO MAY ALLOW RESIDUE OF PROCESSED MATERIAL TO COLLECT ON THE INTERNAL SEALS OF THE BLADE ASSEMBLY, RENDERING THEM INEFFECTIVE.

Wash, rinse, sanitize and dry container prior to initial use and whenever it will not be used again within a period of 1 hour.
Wash and rinse container after each use.
Clean and sanitize motor base prior to initial use and after each use.
Washing solutions based on non-sudsing detergents and chlorine-based sanitizing solutions having a minimum chlorine concentration of 100 PPM are recommended.
SOLUTION| PRODUCT| DILUTION IN WATER| TEMPERATURE
---|---|---|---
Washing| International Products Corporation LF2100 Liquid Low-Foam Cleaner| 1%–2%: 1¼ – 2¾

Ounce/Gallon (lower dilution of 1% for normal cleaning and up to 2% for more stubborn soils)

(8.25% Hypochlorite Concentration)

| 2 Teaspoons/Gallon (Alternately a bleach with 5.25% Hypochlorite Concentration can be used at dilution of 3 Teaspoons/Gallon)|

I n repetitive batch-processing applications, frequent cleaning of the container will prolong the life of the blade assembly. In no case should actual running time between cleanings exceed one-half hour.
Do not use containers to store processed foods or beverages.

TO WASH AND RINSE CONTAINER

REMOVE CONTAINER FROM MOTOR BASE. Remove lid. Rinse container interior and lid under running Add washing solution to container. Scrub and flush out the container interior and lid to dislodge and remove as much food residue as possible. Empty container.
Wipe down exterior of the container with a soft cloth or sponge dampened with washing solution. Wash lid and lid insert in fresh washing solution. Fill container one-quarter full with fresh washing solution, cover (with lid only), place on motor base and run on HI speed for two (2) minutes. Empty container.
Repeat step 2 using clean rinse water in place of washing solution.

IMPORTANT

TO SANITIZE AND DRY THE CONTAINER

Wipe down exterior of container with a soft cloth or sponge dampened with sanitizing
Fill container with sanitizing solution, cover, place on motor base, and run on HI speed for one (1) Empty container. Dislodge any residual moisture from blade assembly by placing empty container on motor base and running on HI speed for two (2) seconds.
Sanitize lid and lid insert by immersing in sanitizing solution for two (2)
Do not rinse container, lid, or lid insert after sanitizing is completed. Allow parts to air-dry.

TO CLEAN AND SANITIZE MOTOR BASE

UNPLUG THE POWER CORD. Wipe down exterior surfaces of the motor base with soft cloths or sponges dampened with washing solution, rinse water, and sanitize solution. Prevent liquid from running into the motor base by wringing all excess moisture from cloths or sponges before using them
Allow motor base to air-dry before

WARRANTY

Waring warrants every new Waring® Commercial Blender to be free from defects in material and workmanship for a period of one year from the date of purchase when used with foodstuffs, nonabrasive liquids (other than detergents) and nonabrasive semiliquids, providing it has not been subject to loads in excess of the indicated rating. In addition, the motor in this appliance has a full two year warranty. Under this warranty, Waring will repair or replace any part that, upon our examination, is defective in materials or workmanship, provided the product is delivered prepaid to the Waring Service Center at: 314 Ella T. Grasso Ave., Torrington, CT 06790, or any Factory Approved Service Center. This warranty does not: a) apply to any product that has become worn, defective, damaged or broken due to misuse or due to repairs or servicing by other than the Waring Service Center or a Factory Approved Service Center, or due to abuse, misuse, overloading or tampering; or b) cover incidental or consequential damages of any kind. The warranty is applicable only to appliances used in the United States or Canada; this supersedes all other express product warranty or warranty statements. For Waring products sold outside of the U.S. and Canada, the warranty is the responsibility of the local importer or distributor. This warranty may vary according to local regulations.