WARING COMMERCIAL CB15 Series Ultra Heavy Duty 3.75 HP Blender Owner’s Manual

1 GALLON BLENDERS
LICUADORAS DE 4 L
MÉLANGEURS DE 4 L
120 V

CB15 Series

For your safety and continued enjoyment of this product, always read the instruction book carefully before using. Para su seguridad y para disfrutar plenamente de este producto, siempre lea cuidadosamente las instrucciones antes del uso. Afin que cet appareil vous procure en toute sécurité beaucoup de satisfaction, lire attentivement le mode d’emploi avant de l’utiliser.

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be taken, including the following:

1. READ ALL INSTRUCTIONS.
   

2. Unplug from the outlet when not in use, before putting on or taking off parts, and before cleaning.

3. To protect against electrical hazards, do not immerse the blender base in water or other liquids.

4. Avoid coming into contact with moving parts.

5. Do not operate any appliance with a damaged cord or plug, or after the appliance malfunctions or is dropped or damaged in any manner. Return the appliance to the nearest authorized service facility for examination, repair, or electrical or mechanical adjustment.

6. The use of attachments, including canning jars, not recommended by the appliance manufacturer may cause hazards.

7. Do not use outdoors.

8. Do not let the cord hang over the edge of the table or counter, or touch hot surfaces.

9. Keep hands and utensils out of the container while blending to prevent the possibility of severe personal injury and/or damage to the blender. A rubber scraper may be used, but only when the blender is not running.

10. Blades are sharp. Handle carefully. 11. Always operate the blender with the cover in place.

11. When blending hot liquids, completely remove the stopper in the cover before turning on the blender. See Hot Blending Instructions, page 9.

12. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge.

13. Children should be supervised to ensure that they do not play with the appliance.

14. DO NOT use carbonated liquids in the blender jar or any blending container. Using carbonated liquids in the included blender jar or any other compatible blender jar may result in injury.

15. DO NOT blend oil or oil-based products as peanut butter for greater than 5 minutes.

16. Never remove the blender jar from the base unit until the blade and coupling have stopped. 18. Spigot assembly must be hand-washed only. Do not run the spigot through the dishwasher.

17. The contents of the blender cannot reach beyond 140° F when operating with a spigot. Note that when blending the temperature of the contents will increase due to the friction of the blade.

SAVE THESE INSTRUCTIONS AND SPECIFICATIONS

• Capacity: 4-liter working capacity
• Rating: 120 Volts–60HZ–Single Phase AC –15.0 Amps. (U.S. models only)
• Base: Die-cast – gray coating
• Container: Stainless steel or copolyester container with stainless steel blades – rubber clamp-on lid
• Bearing: High-performance ball bearing
• Cord: 7 feet (2.44 m) – 3-conductor ground cord with strain relief in base
• Overall Height: 26 inches (66 cm)
• Weight: 38 pounds (17.2 kg) net – Shipping Weight: 41 pounds (18.6 kg)
• cETLus, NSF Listed
• Operating Cycle: 3 min. ON/1 min. OFF

120V GROUNDING INSTRUCTIONS
For your protection, this appliance is equipped with a 3-conductor cord set.
120-volt units are supplied with a molded 3-prong grounding-type plug (NEMA 5-15P) and should be used in combination with a properly connected grounding- type outlet, as shown in Figure 1.
If a grounding-type outlet is not available, an adapter, shown in Figure 2, may be utilized to enable a 2-slot wall outlet to be used with a 3-prong plug. (NOTE: Use of an  adapter is not permitted in Canada and Europe.)

The adapter must be grounded by attaching its grounding lug under the screw of the outlet cover plate. See figure 3.
Caution: Before using an adapter, it must be determined that the outlet cover-plate screw is properly grounded. If in doubt, consult a licensed electrician. Never use an adapter unless you are sure it is properly grounded.

Wiring Color Codes
Green/Yellow: Earth Ground • Blue: Neutral • Brown: Live NOTE: User- installed cord set plugs are not permitted in Europe.

SPIGOT ASSEMBLY (FOR SF MODELS ONLY)
Your spigot assembly includes the main spigot housing,
O-ring and rubber insert.b

1. Plastic Feed Cap
2. Vinyl Lid
3. Metal Clamps
4. Spigot Adapter
5. O-ring
6. Spigot housing
7. Lever
8. Rubber Insert

SPIGOT ASSEMBLY (FOR SF MODELS ONLY)
Your spigot assembly includes the main spigot housing, O-ring, and rubber insert.

The O-ring comes assembled in the jar spigot adapter but can be removed for cleaning. Always make sure the O-ring is positioned securely in the adapter on the jar before inserting and operating the spigot function. Figure 1.

The rubber insert has two loops on the inside to fit the lever (refer to figure 2). The lever only needs to be positioned into the bottom loop. In the event that one loop breaks, you can flip the insert upside down and use the other loop.

To assemble the rubber insert pinch both sides as seen in figure 3 and position the insert inside the housing so that the lever slides inside the rubber insert and the bottom loop (for the lever) is near the spigot hole. Be sure that the bottom of the rubber insert is flush with the bottom of the spigot housing.

Push the bottom of the lever through the bottom loop of the rubber insert.

Once assembled, insert the spigot into the adapter on the jar and rotate clockwise until the spigot completely stops as shown in figure 5.

CB15/CB15P OPERATION

1. Before starting, make sure that the blender cord is unplugged.

2. Position the container assembly on the motor base so that it is firmly seated and not tilted to one side. Plug the blender cord into the outlet.

3. Put ingredients into a container. Always add liquid ingredients first, unless otherwise specified in the recipe. Do not fill the above Max line. Place the cover securely on the container and fasten the cover clamps.

4. Press the STANDBY button to turn on the blender.
   Green LED will illuminate. For continuous operation, press either the LOW, MED or HIGH buttons. When finished blending, press STOP. For momentary operation, press the PULSE button; the motor will run at HIGH speed until the button is released.
   NOTE: Your CB15 utilizes a Slow Start™ feature. When pressing MED or HIGH, the unit will start in the LOW position for 1 second and then switch to the setting selected. This allows for a more even blending of ingredients in a container.

5. Always hold the container with one hand when starting and while blending. Never operate without the jar lid properly clamped in place.

6. Allow the motor to come to a complete stop before removing the container. Never place the container on the motor base or remove it from the motor base while the motor is running.

7. Press the STANDBY button again to turn off the blender.

8. Remove the container from the motor base and empty the contents.

9. Wash and dry the container after each use. See Cleaning and Sanitizing Instructions, starting on page 14.

10. Not for water-jet cleaning.

11. The use of ear protection is recommended during extended operating periods.

CB15T/CB15TP OPERATION

1. Before starting, make sure that the blender cord is unplugged.
2. Position the container assembly on the motor base so that it is firmly seated and not tilted to one side. Plug the blender cord into the outlet.
3. Put ingredients into a container. Always add liquid ingredients first, unless otherwise specified in the recipe. Do not fill the above Max line. Place the cover securely on the container and fasten the cover clamps.
4. Press the STANDBY button to turn on the blender. Press the UP arrow or the DOWN arrow. The initial time will be 10 seconds.
5. Push the UP arrow to set the time required. The timer will advance only in 10-second intervals. The timer can be set to a maximum of 3 minutes.
6. Select and press a speed button; the blender will start and run for the selected time. It will count down in 1-second intervals and stop at 0. NOTE: If you want to increase or decrease time while the timer is counting down, press the UP or DOWN arrows. The timer will increase or decrease in 10-second intervals. After 5 seconds, the timer will turn off and return to manual mode.
7. When using the timer again, the initial time will be the last time set. NOTE: If the unit has been unplugged, the timer will default back to 10 seconds.
8. Always hold the container with one hand when starting and while blending. Never operate without the container lid properly clamped in place.
9. Allow the motor to come to a complete stop before removing the container. Never place the container on the motor base or remove it from the motor base while the motor is running.
10. Press the STANDBY button again to turn off the blender.
11. Remove the container from the motor base and empty the contents.
12. Wash and dry the container after each use. See Cleaning and Sanitizing Instructions starting on page 14.
13. Not for water-jet cleaning.
14. The use of ear protection is recommended during extended operating periods.

CB15V/CB15VP OPERATION

1. Before starting, make sure that the blender cord is unplugged.
2. Position the container assembly on the motor base so that it is firmly seated and not tilted to one side. Plug the blender cord into the outlet.
3. Put ingredients into a container. Always add liquid ingredients first, unless otherwise specified in the recipe. Do not fill the above Max line. Place the cover securely on the container and fasten the cover clamps.
4. Press the green STANDBY button to turn on the blender. Green LED will illuminate and remain steady. Select the desired speed with the variable speed control knob. Press the red START/STOP button to begin blending. You may change the speed with the variable speed control knob anytime during blending. When finished blending, press START/STOP button. For momentary operation, press the gray PULSE button; the motor will run at HIGH speed until the button is released. The green LED will blink during operation.
5. Always hold the container with one hand when starting and while blending. Never operate without the container lid properly clamped in place.
6. Allow the motor to come to a complete stop before removing the container. Never place the container on the motor base or remove it from the motor base while the motor is running.
7. Press the STANDBY button again to turn off the blender.
8. Remove the container from the motor base and empty the contents.
9. Wash and dry the container after each use. See Cleaning and Sanitizing Instructions starting on page 14.
10. Not for water-jet cleaning.
11. The use of ear protection is recommended during extended operating periods.

TO ACHIEVE MAXIMUM SERVICE LIFE, OBSERVE THE FOLLOWING PRECAUTIONS:

1. Do not lubricate container bearing, drive shaft, or shaft seals. These parts are lubricated and sealed at the factory and do not require any further lubrication.
2. Reduce amounts of material processed to less than the full 4-liter capacity when working with viscous or fibrous materials.
3. When cleaning the exterior of the container, keep it in a normal, upright operating position to prevent liquids from running into the bearing through the bottom end.

HOT BLENDING INSTRUCTIONS: IMPORTANT!
To minimize the possibility of scalding when blending hot materials, the following precautions and procedures must be observed:

• Hot materials are those that are 100˚F (38˚C) or hotter.
• Always start blending on the lowest speed setting, then progress to the desired speed.
• Never stand directly over the blender when it is being started or while it is running.
• Constant monitoring of the condition of the container lid gasket and the container lid clamps is mandatory. Replace these parts if they become worn or loose, or are damaged in any way.

FOR CB15S AND CB15TS MODELS ONLY:
Hot Blending Lid Instructions
Model number: CBL10

CAUTION
DO NOT BLEND HOT MATERIALS UNTIL THE BLENDER AND HOT BLENDING LID ARE CORRECTLY ASSEMBLED. WHEN BLENDING HOT MATERIALS ALWAYS FOLLOW THESE INSTRUCTIONS AND THE INSTRUCTIONS IN THE 4 LITER BLENDER OPERATING MANUAL.

TO ASSEMBLE:

1. Place the lid with gasket over the baffle cup and rotate the lid counterclockwise until the locking tabs snap into place with locking tab locks.
2. Place the lid, with the baffle cup attached, on top of the container and lock it with locking clips on the container.

Caution – DO NOT COVER ANY HOLES OR OPENINGS IN THIS LID WHEN HOT BLENDING.
Important – The gasket mounted on the underside of the hot blending lid is a critical component. If it shows signs of cuts, tears, cracking, drying out, wear or other deterioration, it must be immediately replaced before further use. Do not overfill the container; the maximum capacity is 4 liters.c

TO DISASSEMBLE:

1. Be sure the blender is turned off and the lid has cooled.
2. Remove the container from the base.
3. Release the locking clips on the container and lift the lid off.
4. Holding the baffle cup, rotate the lid clockwise until the locking tabs snap open and lift the lid off the baffle cup.

Caution – This hot blending lid retains hot liquids after use. Let cool and handle carefully when disassembling.

MAINTENANCE

Motor – Not for water-jet cleaning.
The Waring Commercial Blender ball-bearing motor requires no greasing or oiling. Sealed-in lubrication provides smooth unit operation.
Container – The stainless steel or copolyester container can be sterilized without injury to the bearing.
Container pad is to be washed and rinsed in solutions as noted in the Cleaning and Sanitizing Instructions.
Depending on the operating conditions, the service life of the main components of the container blade assembly, socket head shaft, and shaft seals is 500 hours of actual running time.
When any one of these main components has worn to the extent that replacement is required, it is likely that the other components will need to be replaced also. It is therefore recommended that container blade assemblies be replaced as a unit.
The Die-cast lock nut must be tightened securely (65 to 70 foot-pounds torque) when reassembling the container.
Power Supply Cord – The power supply cord should not be replaced by the end user. The power supply cord should be replaced only by the manufacturer’s authorized importer (or, in the United States and Canada, by an authorized service center).
NOTE: All parts require constant monitoring for conditions requiring replacement. For assistance, contact your nearest service center.

CLEANING AND SANITIZING INSTRUCTIONS
THE CONTAINER MUST BE CLEANED AND DRIED AFTER EACH USE OF THE BLENDER ACCORDING TO THE FOLLOWING INSTRUCTIONS.
FAILURE TO DO SO MAY ALLOW RESIDUE OF PROCESSED MATERIAL TO COLLECT ON THE INTERNAL SEALS OF THE BLADE ASSEMBLY, RENDERING THEM INEFFECTIVE.

• Wash, rinse, sanitize, and dry the container prior to initial use and whenever it will not be used again within a period of 1 hour.
• Wash and rinse the container after each use.
• Clean and sanitize the motor base prior to initial use and after each use.
• Washing solutions based on non-sudsing detergents and chlorine-based sanitizing solutions having a minimum chlorine concentration of 100 PPM are recommended.

The following washing, rinsing, and sanitizing solutions, or their equivalents, may be used..

• In repetitive batch-processing applications, frequent cleaning of the container will prolong the life of the blade assembly. In no case should actual running time between cleanings exceed a one-half hour?
• Do not use containers to store processed foods or beverages.

TO WASH AND RINSE THE CONTAINER

1. REMOVE THE CONTAINER FROM THE MOTOR BASE. Remove lid. Rinse the container interior and lid under running water. Add washing solution to the container. Scrub and flush out the container interior and lid to dislodge and remove as much food residue as possible. Empty container.
2. Wipe down the exterior of the container with a soft cloth or sponge dampened with a washing solution. Wash lid and lid insert in the fresh washing solution. Fill the container one-quarter full with fresh washing solution, cover (with lid only), place on the motor base, and run on HI speed for two (2) minutes. Empty container.
3. Repeat step 2 using clean rinse water in place of the washing solution.

IMPORTANT

NOTE: IN ORDER TO MINIMIZE THE POSSIBILITY OF SCALDING, THE TEMPERATURE OF WASHING SOLUTION AND RINSE WATER MUST NOT EXCEED 115˚F (46˚C), AND THE QUANTITY USED MUST NOT EXCEED ONE-QUARTER CONTAINER FULL.

TO SANITIZE AND DRY CONTAINER

1. Wipe down the exterior of the container with a soft cloth or sponge dampened with sanitizing solution.
2. Fill the container with sanitizing solution, cover, place on the motor base, and run on HI speed for one (1) minute. Empty container. Dislodge any residual moisture from the blade assembly by placing the empty container on the motor base and running on HI speed for two (2) seconds.
3. Sanitize the lid and lid insert by immersing them in sanitizing solution for two (2) minutes.
4. Do not rinse the container, lid, or lid insert after sanitizing is completed. Allow parts to air-dry.

TO CLEAN AND SANITIZE THE MOTOR BASE

1. UNPLUG THE POWER CORD. Wipe down the exterior surfaces of the motor base with a soft cloth or sponge dampened with washing solution, rinse water, and sanitize the solution. Prevent liquid from running into the motor base by wringing all excess moisture from the cloth or sponge before using it.
   DO NOT IMMERSE THE MOTOR BASE IN THE WASHING SOLUTION, RINSE WATER OR SANITIZE THE SOLUTION.

2. Allow the motor base to air-dry before using.

FOR LABORATORY AND INDUSTRIAL APPLICATIONS
For laboratory and industrial applications, a cleaning/rinsing/ sanitizing/drying schedule similar to that given above for food service applications should be followed, except that the cleaning, rinsing, and sanitizing media used must be modified as required to be consistent with the materials being processed.
For some applications involving the processing of aqueous mixtures, a water- soluble cleaner, a water rinse, and a water-soluble sanitizer may be adequate. In general, however, suitable cleaning, rinsing, and sanitizing media will have to be determined empirically, particularly for those applications involving non-aqueous systems materials not readily soluble in water.
In order to be effective, the cleaning solution used must be capable of breaking up any residues left in the container after use, either by dissolving them, emulsifying them, reacting chemically with them or by some other mechanism.
In order to allow complete removal of the mixture of broken-up residue and cleaning solution, this mixture must, in turn, be either soluble in the rinse medium, or easily suspended by it.
In applications where sanitization of the container is required after cleaning, the sanitizing solution must mix compatibly with any trace liquid that remains after rinsing.

IF YOUR APPLICATION INVOLVES THE PROCESSING OF BIOLOGICALLY ACTIVE MATERIALS AND SHOULD SERVICE ON YOUR UNIT EVER BE NEEDED, WE REQUEST THAT ANY PARTS OR ASSEMBLIES BEING RETURNED BE STERILIZED BY AUTOCLAVING BEFORE BEING SHIPPED. IN ADDITION, ALL SUCH PARTS MUST BE CLEARLY IDENTIFIED AS HAVING BEEN AUTOCLAVED BOTH BY A TAG OR LABEL ON THE PART ITSELF AND BY A STATEMENT IN THE ACCOMPANYING CORRESPONDENCE.
THE DISTRIBUTOR WILL NOT ACCEPT DELIVERY OF SUCH PARTS UNLESS THEY ARE SO IDENTIFIED.

LIMITED THREE-YEAR MOTOR WARRANTY LIMITED TWO-YEAR WARRANTY

Waring warrants every new Waring ® Commercial Blender to be free from defects in material and workmanship for a period of two years from the date of purchase when used with foodstuffs, nonabrasive liquids (other than detergents), and nonabrasive semiliquids, providing it has not been subject to loads in excess of the indicated rating. In addition, the motor in this appliance has a full three-year warranty.
Under this warranty, Waring, during the warranty period, will repair or replace any part that, upon our examination, is defective in materials or workmanship, provided the product is delivered prepaid to the Waring Service Center at 314 Ella T. Grasso Ave., Torrington, CT 06790, or any Factory Approved Service Center. This warranty does not: a) apply to any product that has become worn, defective, damaged, or broken due to misuse or due to repairs or servicing by other than the Waring Service Center or a Factory Approved Service Center, or due to abuse, misuse, overloading or tampering; or b) cover incidental or consequential damages of any kind.
The two-year warranty is applicable only to appliances used in the United States or Canada; this supersedes all other express product warranties or warranty statements. For Waring products sold outside of the U.S. and Canada, the warranty is the responsibility of the local importer or distributor. This warranty may vary according to local regulations.
Warning: This warranty is void if the appliance is used on Direct Current (DC).

SERVICE
Should service on this product in the USA or Canada be required at any time, call or write to:
Waring Service Center 314 Ella T. Grasso Ave.
Torrington, CT 06790 Tel. 800-492-7464 • Fax 860-496-9017
or nearest Authorized Service Center.
Replacement parts for Waring out-of-warranty repairs are obtainable at the above address.
NOTE: If your application involves the processing of biologically active materials, any items returned for service must be sterilized before being shipped. Such items must be clearly identified as having been sterilized, both by a tag on the item itself and by a statement in the accompanying correspondence. Waring will not accept delivery of any returns unless they are so identified.

Any trademarks or service marks of third parties herein are the trademarks or service marks of their respective owners.

©2021 Conair Corporation
Waring Commerical
Waring Products
314 Ella T. Grasso Ave.
Torrington, CT 06790
www.waringcommercialproducts.com
CB15 Series IB
21WC078933/ 033602
IB-12067A/ RV03 2104

Documents / Resources

| WARING COMMERCIAL CB15 Series Ultra Heavy Duty 3.75 HP Blender [pdf] Owner's Manual
CB15 Series, Ultra Heavy Duty 3.75 HP Blender, 3.75 HP Blender, Ultra Heavy Duty Blender, Blender, CB15 Series
---|---

References

• Waring® Commercial

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>