loocam L1 Wire-Free Battery-Powered Security Camera User Manual

loocam L1 Wire-Free Battery-Powered Security CameraBrief information

• Product: Battery camera
• Wireless Encryption: WEP/WPAWPA2 Encryption
• Support System: Android/iOS

Component Description:
Reset Button: Press and hold “Reset” button for 5sec, reset success. It is recommended to insert 8-128GB high-speed Micro TF card, otherwise it may cause failures to store, play recorded video and other malfunctions including firmware upgrade

Part list:

• Battery camera x 1
• Manual x 1
• USB Power Cable x 1
• Screw Accessories Package x 1

Status indicator

During startup, redlight solids means setup failure Red light blinking quickly: pairing mode Green light blinking quickly: Wi-Fi is being connected Solid green light: working normally Yellow light blinking slowly (red and green Iight
blinking): device upgrade Solid white lght charging White light blinking: charging abnormally

Install APP

Download APP: scan the QR code below to download and install. Register and login: open the ” Smart Life” APP to register and login according to the guide in the APP.

Please follow the instructions in the mobile APP (the instructions are for reference only)

Add The Device-Scan QR code mode

• Make sure Wi-Fi is available and connected to the Internet.
• Connect the camera to the power, then system startup completed.
• Open “Smart Life” APP. press the’+” in the upper right corner of the main screen (Figure 01); choose “Security & Video Surveillance, dick “Smart Camera” (Figure 02) to add camera; and then cick “Next step” (Figure 03)

Please note that only 24 GH W-Fi network is supported

• If the moble phone is not connected to Wi-Fi, please click “Connect to Wi-” (Figure 04)
• It will ump to the WLAN interface and connects Wi-Fi (Figure 05).
• If the phone is connected to Wi-Fi (Figure 06), Tap “‘next’:
• AQR code will prompt on phone screen and you need to scan it with the Smart Camera, (the camera is about 20-30 cm away from the mobile
• phone screen). Then tap “I heard a prompt” (Figure. 07. Camera is “connertinn” (Eiaure
• Connection completed (Figure 09), tap “Done”
• It jumps to preview page (Figure 10)
• After closing the device preview page, it returns to the APP home page.
• At this time, the connected device will appear on the APP home page (Figure 11).
• Then you can tap directly to the device page to monitor.

Add The Device-AP Mode

• Select “AP Mode” (Figure 12)
• Click Next (Figure 13)
• Enter the account and password that can connect to WIFI (Figure 14)
• Click “Go Connect” (Figure 15)
• Go to “Smart Life-XXXX “and click Connect (Figure 16)
• Connecting (Figure 17)
• Clck to complete the connection (Figure 18)
• Video screen (Picture 19)

Note
Recommended to install in open space without metal interference; Avoid blocking from furniture, microwave oven, etc; Avoid to install in the space where the audio, video and data lines are wound, and keep away from them as far as possible install as near as possible to wireless Wi-Fi router When changing to the new environment, please press and hold the reset buton for 5 seconds, then connect to the network.

The name and content of the harmful substances in the product

This product conforms to RoHS environmental protection requirements, At present, there is no mature technology in the workd to replace or reduce the ead content in the electronic ceramics. porcelain, optical glass, steel and
copper alloy.

• Maintenance records:
• Maintenance time:
• Fault conditions:
• Fault cause:
• Troubleshooting:-
• Return and exchange proof: .
• Date of valdity
• Original device ID:
• New device ID:
• maintenance personnel signature:
• Maintenance Department seal
• Maintenance voucher of intelligent
• Customer:
• Moble
• Address:
• Model
• Camera ID
• Device store
• Date of purchase:
• Store address
• Store contact number.-.
• Maintenance voucher of intelligent
• Customer
• Mobile:
• Address:.
• Model
• Camera ID:
• Device store:
• Date of purchase:
• Store address:.
• Store contact number.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules, These limits are designed to provide reasonable protection against harmful interfercnce in a residential installation. I his cquipmcnt gcncrates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications, However. there is no guaraniee that interference will noL Occur in a parlicular inslallalion. Ithis equipment does cause harmful interferece to radio or television rcception, which can bc detcrmincd by turning the cquipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:

•  Reorient or relocate the receiving antenna.
• in crease the separation berween the equipnent and receiver,
• Conncct the cquipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution:

Any changes or modifications to this device not explicitly approved by manufaclurer could void your aulhority Lo operale this equipment, This device complics with part 15 of the FCC Rulos. Operation is subject to the following two conditions: This device may not cause harmful interference, andthis device must accept any interference received, including interference thal may cause undesired operation

RF Exposure Information:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator&your body.

References

• Loocam | Look After Yours

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>