Loocam 2BEXF-WT1 PIR Sensor User Guide
- June 1, 2024
- Loocam
Table of Contents
PIR Sensor
Quick Start Guide
Note: This product can not use alone and need to work with Loocam Gateway.
V6.W.02.L
1. What’s in the Box
PIR Sensor Quick Start Guide 3M Adhesive Pad
2. Product Introduction
-
Lens
-
Base
-
Reset Button
-
Battery Compartment
Note: Pictures are for reference only, please refer to the actual product.
3. How to Use?
Download and install Loocam APP
Scan the QR code below with your smartphone or search in the App Store or Google Play to download Loocam app.
Add Devices
1. Connect WiFi to your phone.
2. Please follow the corresponding adding operation to add gateway to the
App.
3. Enter the Gateway interface and select “Add Sensor”– “PIR Motion Sensor”.
4. Unscrew the device housing (as shown in the picture) and insert the
included CR123A battery into the battery slot to power on the sensor.
5. Press and hold the Reset Button for about 5 seconds until the red light flashes on the device and release it. Then press the button one more time and you will see the blue light flashes on the device. At this time, the device enters the pairing mode.
Important Notice: When replacing the battery, please use insulated tools to remove the battery. Do not use metal tools for prying the battery to avoid short-circuiting and damaging the motherboard.
Indicator Light Description
| Status | Color | Feature |
|---|---|---|
| Paring/Upgrading | Blue Light | Flash |
| Reseting | Red Light | Flash |
4. Installation
Location: Select your motion detection area and try to install the sensor in a crossing direction of the monitoring area. (Install the device between 2.2m-3.m for a better detection range.) As shown in the picture.
Overhead View
Overhead View
Methods: Stick the included 3M adhesive pad to the base and then install the base.The base of the sensor has a built-in magnet that allows the sensor to be placed directly on a flat surface made of metal.
Note: To ensure trigger accuracy, the sensor should be installed away from air conditioners, fans, refrigerators, ovens, and other objects that may cause temperature changes.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
[email protected]
www.loocam.com
Responsible Party:Ansjer Electronics Co., Ltd
Company name :Loocam Technology LLC
Address: 2205 Hutton Dr, Unit 100, Carrollton TX 75006
Tel: 657-223-3477
E-mail: [email protected]
Copyright 2023 © Loocam Technology LLC, All rights reserved. Apple and App Store are trademarks of Apple Inc., registered in the U.S. and other countries. Google and Google Play are trademarks of Google Inc.
F9205059A008380