WHITESTONE Smart Pad DOME GLASS User Guide

June 5, 2024
WHITESTONE

WHITESTONE Smart Pad DOME GLASS

Smart Pad Installation Guide

Please make sure to check manual and installation video before using the product.

Products damaged or damaged by user usage, cannot be exchanged or refunded.

After checking the Quick guide, check the User guide.

< Quick guide / User guide>

 Please check the model and components before using the product.

  • Match your device model with the product in advance.
  • Please check all the components listed on the page3 and if there is any problem with the components, please contact us before the installation.

Cautions before Dome glass installation

  • It is not a defective product when wavy pattern appear after attaching the tempered glass. It is caused by the air layer and It will disappear after few days.
  • Tempered glass can be damaged by the excessive power of pressure. Tempered glass includes shatter-resistant film but please be careful to keep your hands safe from any various dangerous factors.
  • Re-attaching the tempered glass is not recommended since it may lose function in the adhesive.
  • No exchanges or refunds for customer’s fault.

Please check the components

Check the jig and suction cups before attaching it!

Model with Jigs

  • Galaxy Tab S7FE

Components

Reference

  • There may be differences in components depending on the model.
  • To improve the product, component’s appearance or specifications etc. can be change without prior notice.
  • Some components can be purchased separately if necessary.


Installation

STEP1
Wipe the smart pad clean using alcohol cotton and microfiber.

STEP2
Place the attachment jig on the device.

STEP3 Remove the dust using the dust removal sticker.

STEP4
Remove the liner film on the back of the tempered glass and carefully place the glass from bottom to the top as shown in the image. Make sure not to touch the adhesive surface of the glass.

STEP5
Draw “+” sign on the center of the glass in order to attach it properly. Once the adhesive spreads out and covers the whole screen, remove the jig. If air bubbles occur after attachment, push them outward from the center of the tempered glass using the cleaning cloth.

· Please re-register your fingerprints after attaching or detaching the product.
· Please note that the fingerprint recognition rate may decrease after attaching the product.

Models Without Jigs

  • iPad Air 10.9
  • iPad Pro 11
  • iPad Pro 12.9
  • iPad 9.7 / 11 / 12.9

Components

Reference

  • There may be differences in components depending on the model.
  • To improve the product, component’s appearance or specifications etc. can be change without prior notice.
  • Some components can be purchased separately if necessary.

Installation

STEP1
Wipe the smart pad clean using alcohol cotton and microfiber.

STEP2
Remove the dust using the dust removal sticker.

STEP3
Remove about 1/3 of the liner film (Tag#2) of the tempered glass and align the tempered glass with the top, bottom, left and right sides of the SmartPad. After aligning the tempered glass with the SmartPad, remove the remaining liner film to the end. Do not touch the adhesive side.

STEP4
Draw a “+” shape with a finger on the center of the tempered glass, adhered part is gently spread and attached. If air bubbles occur after attachment, push them outward from the center of the tempered glass using the cleaning cloth.

· Please re-register your fingerprints after attaching or detaching the product.
· Please note that the fingerprint recognition rate may decrease after attaching the product.

Model with Suction cups

  • Galaxy Tab S5e

Components

Reference

  • There may be differences in components depending on the model.
  • To improve the product, component’s appearance or specifications etc. can be change without prior notice.
  • Some components can be purchased separately if necessary.


Installation

STEP1
Wipe the smart pad clean using alcohol cotton and microfiber.

STEP2
Place the attachment jig on the device.

STEP3
Attach the provided suction cups approximately 13cm from each other. Then, holding on to the suction cups, remove the liner film. Please do no touch the adhesive side.

STEP4
Holding on to the suction cups, align the Tempered glass to the center of the smart pad screen and lay down gently to apply.

STEP5
Quickly remove the suction cups. Lightly tap the center of the Tempered glass and slide your finger across the center on the shape of a across. The adhesive will spread out smoothly and stick. If there are any bubble, use the Cleaning Cloth to move the bubbles towards the edges.

Sticker Type

  • iPad 10.2
  • iPad Pro 12.9

Components

Reference

  • There may be differences in components depending on the model.
  • To improve the product, component’s appearance or specifications etc. can be change without prior notice.
  • Some components can be purchased separately if necessary.


Installation

STEP1
Attach 2 Dust removal sticker on the top of the film for align film with device.

STEP2
After align the film with device, attach the sticker onto the device. (The film and the device has to be aligned during the process)

STEP3
After cleaning the device with alcohol wipe and microfiber cloth, life the film gently and remove Back side liner film(Blue) to attach the film from the top.

STEP4
Adhere the film onto the device by removing the air bubbles by using the squeegee.

STEP5
After finishing the attachment process, please remove the dust removal stickers with Front liner film (Red). If you find any air bubble, please remove it with the squeegee.

Please check the installation Guide.

Precautions after installation

  • Glass may be damaged by impacts or external strength.
  • Although glass includes shatter-resistant film, recommend users change the glass to new one once glass is broken in order to prevent any harm.
  • Bubbles or lifting may occur by physical impacts such as drop impact, incompatible phone cases use, excessive strength while cleaning with alcohol wipes or etc.
  • No refund or exchange for any type of user damages. · Refer to the Reuse of Jig manual when reusing the jig.

Precautions when removing the tempered glass

  • When removing the tempered glass from the device, face it towards the ground before removing.
  • Remove it outdoors or near a trash can.
  • Use your fingernails and slowly lift the glass from the corner to remove it (Removing it suddenly could lead to damages or injuries)

Global A/S
CONTACT US
feedback@whitestonedome.com
HOMEPAGE
www.whitestonedome.com

WARRANTY REQUEST
We always provide friendly and fast service to your questions.
WHITESTONE Ltd.
27, Baekseokgongdan7-ro, SeoBuk-gu, Cheonan-si, Chungcheongnam-do, Republic of Korea

The unique Component Manufacturer, Whitestone (www.whitestonedome.com) for Mobile Device.
Copyright 2021 Whitestone Ltd. All rights reserved.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals