WHITESTONE DOME Premium Genuine Film User Manual

June 4, 2024
WHITESTONE

WHITESTONE DOME Premium Genuine Film User Manual
WHITESTONE DOME Premium Genuine Film

Please make sure to check manual and installation video before using the product.

Products damaged or damaged by user usage, cannot be exchanged or refunded.

After checking the Quick guide, check the User guide.

 Please check the model and components before using the product.

  • Match your device model with the product in advance.
  • Please check all the components listed on the page3 and if there is any problem with the components, please contact us before the installation.

Cautions before Dome silk installation

  • Watch the Installation video and manual carefully before start to install.
  • Please see all introductions, since each device has different installation way.
  • Install the film after removing any film on the screen.
  • Please avoid a dusty place.
  • Be careful of any impacts while getting out the jig from the box in order to prevent any damage.
  • Be careful not to force the jig apart or break it.
  • If there is a problem with the subsidiary materials, please do not attempt installation and contact customer service immediately.

Components

Reference

  • There may be differences in components depending on the model.
  • To improve the product, component’s appearance or specifications etc. can be change without prior notice.

There are differences in components depending on the model, so please check the components of the product purchased before attaching it.

Components

  • Align block
    Components

  • Dust Remover Sticker

  • Remover

  • Stopper
    Components

  • Squeegee
    Components

  • Cleaning Cloth

  • Alcohol Wipes

Installation

STEP 1

Remove the protection film attached to your device using the Remover.
Installation instruction
Connect the Align block to top part of the JIG.

  • Correct gudie film removal direction
    Removal Direction

  • Incorrect gudie film removal direction
    Removal Direction

STEP 2

Installation instruction

STEP 3

Insert the device into the JIG in correct direction.
Installation instruction

STEP 4

Clean the display with alcohol wipe and cleaning cloth.
Then, remove any dust with dust removal sticker.
Close the device to the stopper.
Installation instruction

STEP 5

Hold the top part of the film as shown, and bend the [1 sticker] as shown in [Figure 1].
Like [Figure 2] Make sure that the protective film and pet film are properly separated and slowly remove the protective film. If it is as shown in [Figure 3], attach the protective film as if it is in the first state and remove it carefully so that only the protective film can be removed.
Installation instruction
Installation instruction
Installation instruction

STEP 6

Flip the film with the protective film removed so that the top/bottom text are visible to the front.

  1. Insert the top part of the film into the Align block.
  2. Insert the bottom part of the film into the bottom part of the JIG
    Installation instruction
  • Please do not touch adhesion surface
  • Make sure the Film does not stick onto the device

STEP 7

Slowly and forcefully push up with the squeegee from the bottom of the jig to the top while maintaining squeegee in a lean angle. Push the squeegee all the way to the end.

Bubble might be appeared if you push the squeegee too fast.
Installation instruction

STEP 8

Remove the guide film from Jig’s hole while pressing the ①-top/②-bottom of the film with a squeegee. ③Push the film entirely to the short side of the squeeze.

Directions For use

Installation instruction
Installation instruction

STEP 9

Bend the guide film attached to the film and remove it from the top.
Finish by pressing the film edge with the short part of the squeegee.
Remove the device from the JIG.
Installation instruction

  • Micro bubbles will disappear within a week.

  •  Please do not press the bubbles or lines after the installation, it will be naturally disappeared.
    Installation instruction

    • Correct gudie film removal direction
      Removal Direction

    • Incorrect gudie film removal direction
      Removal Direction

Installation-Outer display

(There are differences in components depending on the model)

STEP 1

Use the alcohol wipe and the cleaning cloth to wipe down the device.
Remove any dust on your device with the dust remover sticker.
Installation-Outer display

STEP 2
Remove liner film(back).
Align the film starting with the top edges of the device.
Installation-Outer display

STEP 3
Tilt the protective film (1)180° and push with a squeegee to attach it.
Tilt the protective film (2)180° and push with a squeegee to attach it.
Installation-Outer display
Installation-Outer display
Installation-Outer display

STEP4
Remove any bubbles with a squeeze.
With a dust removal sticker remove the front protective film.

  • Please do not press the bubbles or lines after the installation, it will be naturally disappeared.
    Installation-Outer display

STEP5-Hinge

  • Use the alcohol wipe and the cleaning cloth to wipe down the device.
  • Remove liner film[1].Place it on the device and attach it in position.
  • Tilt the protective film (2)180° and push with a squeegee to attach it.
  • Tilt the protective film (3)180° and push with a squeegee to attach it.
  • With a dust removal sticker remove the front protective film.
    Installation-Outer display

Please check the installation Guide.

Precautions after installation
  • Bubbles or lifting may occur by physical impacts such as drop impact, incompatible phone cases use, excessive strength while cleaning with alcohol wipes or etc.
  • No refund or exchange for any type of user damages.

CONTACT US

feedback@whitestonedome.com

HOMEPAGE

www.whitestonedome.com

WARRANTY REQUEST

We always provide friendly and fast service to your questions.

** The unique Component Manufacturer, White stone (www.whitestonedome.com) for Mobile Device.
Copyright ⓒ White stone Ltd. All rights reserved.**

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals