EUROM 334180 Q-time 1500 Coolblue Luxury Heater Instruction Manual

EUROM 334180 Q-time 1500 Coolblue Luxury Heater

Technical data

General safety warnings

1. Use the terrace heater only for the purpose for which it is designed: heating a terrace, garden or other outdoor domestic spaces and NOT for heating indoor spaces, outdoor non-domestic spaces or for drying textile and/or other
2. Carefully read this entire manual before using and/or installing this Keep the manual in order to be able to consult it in the future and possibly to pass it on to other people.
3. Check this new appliance before you use it (including cable and plug) for any visible Do NOT use a damaged appliance, but bring it to your supplier for replacement. Improper use and/or installation entail risks of electric shocks

Warnings for installation and positioning

1. Use the terrace heater only outdoors or in a very large open Keep all flammable objects, such as tent cloths, parasols, branches, furniture/garden furniture, curtains, paper, etc. away from the appliance (minimum 1 metre, also when they are windblown!). Always take care of good ventilation!
2. Observe the following minimum distances when installing the appliance: Minimum distance from the ceiling /roof: 30 cm Minimum free distance at the front side: 100 cm Minimum distance to the sidewalls: 50 cm Minimum distance to the floor: 180 cm
3. The ceiling and wall that are used for mounting the appliance must be made from non-combustible or hardly combustible In any case, they should withstand a temperature of minimum 150°C without starting to singe, melt, deform or ignite. Check regularly whether the wall and ceiling do not become overheated, because this poses risks!
4. Some parts of the appliance become extremely hot or the protective grids do not provide sufficient For safety reasons, the lowest point of the appliance must always be at a distance of 180 cm from the ground.
5. The air around the appliance should be able to circulate Therefore, do NOT place it too closely to large objects. The minimum distances between large objects and the top, sides and bottom of the appliance are equal to the aforementioned distances to ceiling/roof, front side, sidewalls and floor.
6. The terrace heater is intended only for domestic Therefore, do NOT use it on construction sites, in greenhouses, sheds, stables, etc., even if these are largely open spaces. Usually, these spaces contain too many flammable substances.
7. Do NOT use this terrace heater for sauna heating, room heating, and heating of a kennel or another location in which there are
8. If you use the appliance outdoors, it should be connected to a suitable, waterproof and earthed All electrical connections must stay dry under all circumstances. The manufacturer, importer and supplier are not liable for incorrect connections!
9. Do NOT use this appliance before it is completely installed as described in the NEVER use the appliance when it lays down, leans or similar. Do NOT insert the plug into the wall socket before the appliance is correctly installed in its final place.
10. Do NOT place the appliance above a faucet, another source of water, or within a distance of 1 metre from these objects. Do NOT install it in a humid environment, such as bathrooms, laundry rooms or similar indoor places. Be careful with water regardless of the fact that the appliance is splash-proof. Make sure that the appliance cannot fall into water and do NOT expose it to hard or brutal waterjets. Do NOT operate or touch it with wet hands. Install the appliance in such a manner that nobody can operate or touch it from a bathtub, shower or swimming pool.
11. Use the appliance only when it is firmly Make sure that you always use fasteners suitable for the substrate and if necessary, consult an expert.
12. If this appliance will be connected directly to the cabling of your electricity installation, an authorised specialist should install it while taking into account the applicable legislation, regulations and
13. Do NOT place the appliance near, under or pointing towards a socket and do NOT place it near open fire or heat
14. Do NOT use the appliance near or pointing towards furniture/garden furniture, parasols, tent cloths, branches, flags, paper, clothing and other flammable Maintain at least 1 metre distance between these objects and the appliance!
15. The inside of the appliance contains hot and/or glowing and sparking Therefore, do NOT use the appliance in spaces for storing combustible liquids and/or gases such as fuels and paint. Do NOT use the appliance in locations where there is a risk of fire, such as near gas tanks, gas pipes or spray cans. That entails the risk of explosion or fire!
16. When selecting a place for the appliance, take into account that this place cannot be reached / accessed by
17. Warnings regarding use
18. Do NOT use additions/accessories in/on the appliance that are not recommended or supplied by the
19.   Use the appliance only for the purpose for which it is designed and only in a manner as described in the user

3.   Some parts of this appliance become extremely hot and can cause burns. Special attention is needed when children, vulnerable persons or pets are near the appliance. NEVER leave them alone if the appliance is operating!

15. Make sure that the infrared heater is always pointing down and NEVER towards the ceiling to prevent overheating the ceiling!
16. NEVER cover or block the appliance, which causes overheating and entails the risk of NEVER hang or put objects such as clothing, blankets, pillows, etc. on the appliance. Always observe a minimum distance of 1 metre between the appliance and flammable materials. To prevent fire, ventilation openings must not be blocked. NEVER use the appliance for drying clothing and NEVER put something on it. Nothing may lean against the appliance!
17. Warning! NEVER leave an operating appliance without Do NOT put the appliance automatically into operation by means of a timer or any other device that switched on the appliance
18. automatically. Always check that the appliance stands in safe conditions before using it! Do NOT use the appliance by means of a voltage regulator such as a dimmer or something similar; that is also dangerous!
19. The connection voltage and frequency stated on the appliance should correspond with the voltage and frequency of the wall socket that you are The wall socket must have an earth connection and the electrical installation should be protected using a 30mA residual-current circuit breaker. At all times, the wall socket used should be easily accessible in order to be able to remove the plug from the socket in case of an emergency.
20. To prevent overloading and blown fuses, other devices may not be connected to the same wall socket as the socket to which the appliance is
21. Completely unwind the electric cable of the appliance before inserting the plug into the wall socket and ensure that the cable does not touch the hot parts of the appliance anywhere or can become hot in another Do not put the electric cable under carpets, mats, runners, etc. and keep the cable out of the walkway. Make sure that no one steps on it and that garden furniture/furniture is not put onto it. Do not lead the cable around sharp corners and do not wind it too tightly after using it! Prevent the cable from making contact with oil, solvents and sharp objects. Regularly check the cable for damage. Do not twist or bend the electric cable or wind it around the appliance; these things can damage the insulation!
22. It is recommended not to use an extension cable, because that can cause overheating and If using an extension cable is unavoidable, ensure that you use an undamaged and approved earthed extension cable with a minimum diameter of 3 x 2,5mm² and a minimally allowed power of 2000 Watt. Always unwind the extension cable completely to prevent overheating.
23. Connect the appliance only to a fixed wall Do NOT use a junction box, power strip, etc.
24. The plug can feel lukewarm while the appliance is This is normal, but if the plug gets very hot, then there is something wrong with the wall socket. Please contact your electrician.
25. . Always switch off the appliance initially using the main switch and subsequently, remove the plug from the wall socket. NEVER switch off the appliance by removing the plug!
26.  NEVER pull the electric cable to remove the plug from the wall socket or to move the appliance.
27.  Prevent any strange objects from penetrating the radiation/ventilation openings. This can cause an electric shock, fire or damage.
28.  NEVER stick fingers into the appliance through an opening.
29.  NEVER leave an operating appliance without supervision; first, switch off the appliance and subsequently, remove the plug from the wall socket.
30.  Always remove the plug from the wall socket, when the appliance is not operated. For this purpose, grasp the plug; NEVER pull the electric cable!
31.  The housing and the front side of the appliance become extremely hot during its operation. Therefore, do NOT touch the appliance during or shortly after its operation: that causes burns! Payattention that wind or other environmental factors do not bring flammable materials, such as branches, parasols, tent cloths, flags, plastic foils, etc., in the vicinity of the appliance. This can cause damage/singe damage or fire. Pay attention that these objects/materials do not cover or block the appliance.
32.  Warning! This appliance is not equipped with a device to regulate room temperature. Do NOT use this appliance in small rooms, when these are used by persons that are not able to leave these rooms independently unless there is continuous supervision.

Who is allowed to use the appliance?

1.  Children, who are younger than 3 years old, should be kept away of the appliance, unless there is supervision.
2.  Children between the ages of 3 and 8 are only allowed to switch the appliance on or off, if it is placed or installed in its normal workplace and if there is supervision or if they have received instructions for using the appliance safely and understand which risks are related to using it. Children between the ages of 3 and 8 are NOT allowed to insert the plug into the wall socket, regulate or clean the appliance and carry out maintenance.
3.  This appliance can be used by children, who are over the age of 8, and by persons with reduced physical, sensory or mental skills or lack experience and knowledge, if there is supervision or if they have received instructions for using the appliance safely and understand which risks are related to using it.
4.  Children are not allowed to clean and maintain the appliance without supervision.
5.  Children are not allowed to play with the appliance.

Warnings regarding maintenance

1.  NEVER change anything in the appliance, electric cable or plug.
2.  Keep the appliance clean, because dust, dirt and/or sediment is often the reason for overheating. Make sure that such sediment is removed regularly.
3.  NEVER submerge the appliance in water to clean it.
4.  Always switch off the appliance, remove the plug from the wall socket and let the appliance cool down, when you:
5.  Want to clean the appliance.
6.  Want to carry out maintenance.
7.  Want to touch or move the appliance.
8.  Do NOT put the appliance into operation, if you observe damage to the appliance, electric cable or plug, or if it operates poorly, makes unusual noise, has fallen or if you smell something, see smoke or observe some other fault. Remove the plug from the wall socket immediately. Return the entire appliance to your supplier or a qualified electrician for a check and/or repair. Always demand original spare parts.
9.  Only authorised and qualified persons are allowed to open and/or repair the appliance. Do not repair the appliance yourself; that can be dangerous! Repairs by unauthorised persons or changes to the appliance breach the water and dust tightness of the appliance and cause the warranty and liability of the manufacturer to be cancelled.
10.  If the electric cable is damaged, it should be replaced by the manufacturer or its service employee or persons with similar qualifications to prevent risks.

Description

1.  Heating element quartz
2.  Peep hole
3.  Pull switch

Location and connection

•  Remove all packaging material and keep out of reach of children. Pay attention to the mounting material!
•  After removing packaging, check the appliance for damage or other signs that could indicate a fault/defect/malfunction. In case of doubt, do not use the appliance, but contact your vendor for inspection or replacement.
•  Select a suitable location for the device taking into account all the aforementioned warnings in this manual.
•  This heater has been designed to be hung horizontally from a wall; therefore do not use it whilst it is standing, lying or in any other way!
•  Pay attention to the mounting place for your heater. The appliance has to be mounted on an incombustible foundation. That foundation has to be vibration free, exact vertical and stable enough for lastingly holding the appliance free of problems. Check or the provided dowels and screws are suitable, strong enough and qualified for the foundation. The material provided is identified for a brick wall; for another foundation please ask the specialist for suitable material.
•  Before mounting, check whether the spot you have chosen complies with the minimum safety distances from the environment. The distance between the bottom side of the heater and the floor must be at least 1.8 metre. The distance between the top side of the heater and the ceiling, roof, etc. must be at least 0.3 metre. However, if the ceiling or roof is made of flammable material (e.g., canvas), then the minimum distance is 1 metre. On both sides of the appliance, the minimum distance to walls, etc. must be 0.5 metre. If you mount the appliance outdoors, then make sure that it is not situated where it gets direct wind.
•  The insulation of the Q-time 1500 is IP24 rated (splash proof). A distance of at least 1 m has to be maintained between the heater and baths, taps, fountains, showers etc. Make sure that no jets of water can be directed at the Q-time 1500 and that the heater cannot fall into the water.

Permanent mounting
The Q-time 1500 is designed for installation in a permanent position and direct connection to the electricity network. For safety reasons, this installation should be fitted by an approved electrician.
Plug connection
The Q-time 1500 can also be connected directly to a power socket using the electric cable and plug. Make sure that the electric cable does not hang over any (sharp) edges, does not make any sharp angles, cannot be dragged and does not touch any hot surfaces. Important: the electric cable and plug form a whole. Therefore, if either the electric cable or plug is damaged they should both be replaced by an electrician. Only mount the original parts!

•  When positioning and connecting the heater, make sure that your hands do not touch the heating elements. This is because traces can be left behind which, afterwards, will have a negative effect on the radiated heat.
•  For use with a plug, the following applies: do not use extension leads and do not connect any other equipment next to the heater in the same socket!
•  Position the mounting bracket with the long side and 2 holes against the wall in the required position, then mark the drill holes. Make sure that the drill holes are positioned at the same height! Remove the bracket and drill 2 holes in the spots marked. Knock in the raw plugs, position the bracket over the top and screw it firmly into the wall using the screws supplied.
•  Place the heater over the bracket with the cord down and large holes positioned over large holes. Screw securely using the bolts, rings and nuts supplied (1).
•  Turn the heater to the required position. The body of the heater can be turned to 5 positions (small heater holes (3) over small bracket holes (2)). The midposition is horizontal to the room. The two positions which are directed upwards will only be used in exceptional cases and require a greater distance to the ceiling (2 metre). Finally, the heater has two positions which are directed downwards. These are the standard positions. Secure the heater at the required angle by screwing both of the small screws into the double holes.
•  The heater is now ready for use.

Use

To use the heater, if required insert the plug into the socket and pull on the pull switch. Each time that you pull the pull switch, the heater will change to the next setting:
0 (off) > 1 (500W) > 2 (1000W) > 3 (1500W) > 0 etc. You are able to view the heater’s setting through the peephole.

Cleaning and maintenance

Before you perform maintenance on the heater, you have to turn off the power supply. This heater does not require any specific maintenance. Keep the ventilation and radiation openings, as well as the heat screen, clean and dust-free, but when cleaning the quartz elements, make sure that you do not touch them; it is best to blow any dust away frequently. To clean the exterior, use a soft cloth which can be damp. At the very most, use a mild cleaning agent: no abrasives or sponges and no caustic substances. If a defect occurs, disconnect the heater from the power supply and go to a service point. Do not perform any repairs yourself and always ask that original parts are used in any repairs.

References

• Eurom - Powerful products - producten voor comfort en gemak

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>