WINTORY POD1 True Wireless Stereo Earphone User Manual
- June 5, 2024
- WINTORY
Table of Contents
WINTORY POD1 True Wireless Stereo Earphone
Usage Instructions
Thank you for choosing the VWINTORY POD1″True Wireless Stereo Earphone”! To
better use this product, please read the Quick Start Guide carefully beforeuse
and properly manage it.
Please tear off the insulation film on the charging pins and then fully charge
the earbuds before use.
Product Specifications
Product Information
How to pair
Powering On
Ihe earphones will automatically pOwer on when taken out of the charging case.
In power-off state, press and hold the MEB button for 1.5 seconds to turn them
on, The red and blue indicator lights are on for 1 second at the same time,
and the power on prompt sounds.
Powering Off
Ihe earphones will automatically pOwer off when placed back into the charging
case. In power on state, press and hold the MFB button for 3 seconds to power
off, the red light indicator lights up for 1 second, and the “Power off ”
prompt sounds.
Note : When two earphones are in the connection mode at the same time,
when you turn off any one of the headphones, and the other can be used alone.
How to pair? ( first use)
When take the earphones out of the charging case, the left and right earphone
will be paired after the red and blue lights flash alternately, and wait for
atbout 10s. After the pairing is successful, one side of the earphones will
flash 5s one times, and the other side will slowly flash red and blue,
indicating that the earphones is pairing successfully. Turn on the Bluetooth
on the mobile phone, then search for the Bluetooth device WINTORY POD1″ and
click connect. After the connection is suCcessful, a “Connected tone will
sound.
Note: Please notice that using only one earphone mode may cause the
unpaired result of left and right earphones.
How to Control
- Turn on the earphones: The earphones will automatically power on when taken Out of the charging case ( or in the off state, press and hold the MFB button for 1.5 seconds to turn It).
- Turn off the earphones: The earphones will automatically power off when placed back into the charging case (or in the power-on state, press and hold the MFB button for 3 seconds to turn it off).
- Play/Pause: Click the left/ right earphone MFB button.
- Previous song click on the right earphone MFB buttorn. Answer / end call: Click the left or right earphone MFB button. Reject call: Long press left or right earphone MFB button for 1 second.
- Clear pairing information: Hold down the MFB for 10s in power-off mode to clear pairing information.
- Secure pairing: When the mobile phone is connected to a Bluetooth device lower than
- Bluetooth version 3.0, a password is required, enter the default security code “0000 to pair with your mobile phone.
- Automatic power-off: If the left earphone is not connected to a phone, it will be automatically powered ott in 5 minutes so as to save power. If the right earphone is not
- Connected to the left earphone, the right earphone will be also automatically powered off in 5 minutes.
- Next song: Double-click on the left earphone MFB button/ Double-
- Reset: Put the earphones into the charging case.
- Activate voice assistant: Triple-click L/R MFB button.
How to charge
Charge the charging case.
Please use a low power charger below 5V-2.1A to charge. The white charging LED
indicators flash during charging. The number of flashing indicators varies
with the battery level. All indicators turn solid white when the case is fully
charged (a full charge takes about 3 hours).
Charging the earbuds
Put leit and right earbuds into the charging case. The red indicator on both
earbuds will be on. When the earbuds are fully charged, the indicator will be
off. A full charge takes about 2 hours. A fully-charged charging case can be
prOvides 3 times cycles ot a full charge povwer for the earphones.
Low battery level indication
If the battery level of the charging case is low, the low-battery indicator on
the charging case will show only one grid (25% left), reminding you to charge
the charging case.
When the battery level of the earbuds is low, the Bluetooth indicator on the
earbuds will turn red and a low-battery beep Please charge sound can be heard.
Important satety intormation
Caution: If you do not intend to use the headset for a long time, charge the headset once every 20 to 30 days to ensure its expected service life. Don’t remove or replace the Battery,including sensitive electronic components, including a battery,and can be damaged or cause injury if dropped, burned, punctured, crushed disassembled, or if exposed to excessive heat or liquid.Don’t use damaged batteries and electronic Components.
Dispoal and recycling information
Don’t treat the product and battery as a household waste or into a fire. When
you decide to dispose of the product and its battery, please follow the local
environmental laws to handle the battery to avoid an explosion.
Medical device interterence
The product contains components and radios that emit electromagnetic fields
and also Contains magnets. These electromagnetic fields and magnets may
interfere with pac emakers,defibrillators, or other medical devices. Maintain
a safe distance of separation between your medical device and product.Consult
your physician and medical devicemanufacturer for information specific to your
medical device. Stop using product if you SUspectit is interfering with your
pacemaker, defibrillator, or any other medical device. Please charge the
battery fuly before use.Please use a low-power charger beloW
5V-2.1A to charge, otherwise it will cause the headphones to damage
EU Declaration of Conformity
Hereby, Dongguan Uiisi Electronics Co., Ltd declares that the radio equipment
of type Bluetooth Uiisii TWS60 is in compliance with Directive 2014/53/EU.The
full text of the EU declaration of conformity is available at the following
internet address:http://www.uiisii.com/doc/
NOTE:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequerncy energy and, if not installed and used in accordance with the
instructions,may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the intertference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- onnect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- onsu the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. This
device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>