Citizen Q Q 0D19137 Sports Watch User Guide

Citizen Q Q 0D19137 Sports Watch

CITIZEN WATCH CO.,LTD. Q&Q SALES DEPARTMENT

ATTENTION

1. Never try to open the case or remove its back cover.
2. Do not operate buttons underwater.
3. Should moisture appear inside the watch, have ii checked immediately by your dealer. Otherwise it can cause erosion of the metal parts of the watch.
4. Though the watch is designed to withstand normal use, you should avoid rough use or dropping the watch.
5. Avoid exposing the watch to temperature extremes.
6. Wipe the watch with dry, soft cloth only. Avoid allowing it to come into direct contact with chemical materials, which can cause deterioration of the plastic parts of the watch.
7. Avoid to wear the watch in electromagnetic, static conditions.

MODE SELECTION

• Press “B” to change mode to mode in the following sequence:
  Timekeeping Mode – Stopwatch Mode – Countdown Mode – Alarm Mode – World Time Mode.

TIMEKEEPING

• 12/24H Format;

• Hour, Minutes, Seconds,
  Day of week, Year, Month,Date;

• 100 years Calendar
  (2000 – 2099).

STOPWATCH

• 1/100 second unit;
• Measuring range:
  0’00″00 – 99:59’59”.

COUNTDOWN

• Countdown range:
  99:59’59” – 0’00″00.

ALARM

• 5Alarms;
• Hourly time signal;
• The alarm sounds at the preset time each day.

WORLD TIME

• The time for other time zone.

TIMEKEEPING

Time Setting

1. In the timekeeping mode, press and hold “A” until the city code will flash(flashing is indicated in the setting mode);

2. Press “C” or “D” to select the city code, press and hold to adjust at high speed;

3. Press “B” to select the Daylight Saving Time;

4. Press “C” or “D” to turn ON/OFF the Daylight Saving Time.

5. Repeat steps 3 and 4, the selection in the following sequence:
   City code .. Daylight Saving Time .. Seconds .. Hour ..
   Minutes -12/24H Format .. Year .. Month .. Date Key Tone(ON/OFF);

6. Press “A” to exit the set state after setting (The day of week is automatically displayed in accordance with year, month and date setting).

STOPWATCH

A Lap Time

1. In the stopwatch mode, press “D” to start the stopwatch;

2. To stop the stopwatch by pressing “D” again;

3. Press “A” to reset the stopwatch.

Split Time

1. In the stopwatch mode, press “D” to start the stopwatch;

2. Press “A” to display the split time, stopwatch timing continues internally;

3. Press “A” to clear the split time and to continue time measurement;

4. Repeat step 2 and 3, you can measure the multi split time;

5. Press “D” to stop the stopwatch.

COUNTDOWN

• When the countdown reaches zero, the alarm sounds for about 10 seconds and press any button to stop it.

Countdown Timer Setting

1. In the countdown mode, press and hold “A” until the hour will flash (flashing is indicated in the setting mode);

2. Press “D” to increase the hour, press “C” to decrease the hour, press and hold to adjust at high speed;

3. Press “B” to select the next selection;

4. Press “D” to increase the number, press “C” to decrease the number, press and hold to adjust at high speed;

5. Repeat steps 3 and 4, the selection in the following sequence:
   Hour – Minutes -Seconds;

6. Press “A” to exit the set state after setting.

Use Countdown Timer

1. Press “D” to start the countdown timer;

2. To pause the countdown by pressing “D” again.

3. Press “A” to reset the countdown.

ALARM

• The alarm sounds at the preset lime each day for about 1 0 seconds, press any button to stop it.

Alarm and Chime

• In the alarm mode, press ” C “to select chime, Alarm1 -Alarm5.

• In the chime state, press “D” to on/off the chime.

• In theAlarm1 -Alarm5 state, press “D” to on/off the alarm.

Alarm1 Setting

1. In the alarm state, press and hold “A” until the hour will flash, (flashing is indicated In the setting mode);

2. Press “D” to increase the hour,press “C” to decrease the hour, press and hold to adjust at high speed;

3. Press “B” to select the minutes;

4. Press “D” to increase the minutes, Press “C” to decrease the minutes, press and hold to adjust at high speed;

5. Press “A” to exit the set state after setting.

   • Setting and operation of the Alarm 1-Alarm5 are the same.

WORLDTIME

1. In the world time mode, press “C” to forward select the time zone, press “D” to backward select the lime zone, press and hold to adjust at high speed;

2. In the world time mode, press and hold “A” to turn ON/OFF the Daylight Saving Time (except “GMT+0”).

SELECT TAIL

• In the timekeeping mode, press “D” to select different dials.
  

• 4 dials for user to choose.

• In the timekeeping mode, press and hold “D” to switch T1 or T2 display.

BUTTONS

• Button operation are indicated using the letters shown in the illustration.

LOW POWER

• If the battery voltage level is insufficient, the icon “i.:::i” will appear to remind to replace a new battery.

DISPLAY

• The screen shown in below:

EL BACKLIGHT

• The backlight that uses an EL, causes the display to glow for easy reading in the dark.

Use Backlight

• In the timekeeping mode, press “C” to illuminate the EL about 3 seconds.

World Time Form

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>