TESY WEF200SRELW TR Electric Fireplace Instruction Manual

TESY WEF200SRELW TR Electric Fireplace

IMPORTANT SAFETY MEASURES AND PRECAUTIONS

WARNING

• Please read this manual before operating the appliance and keep it at a safe place for future reference. In case the appliance is obtained by a new owner, it should be transferred together with its manual.

• CAUTION: Children under 3 years of age should be kept away from the appliance unless they are under constant supervision. Children from 3 to 8 years of age are allowed to operate the on/off button ONLY, provided that the appliance is installed and ready for operation and such children have been supervised and instructed in safe operation of the appliance and they understand all related risks. Children from 3 to 8 years of age

• MUST NOT: connect the plug to power sockets, make adjustments, clean it or carry out user maintenance operations.
  This appliance can be used by children older than 8 years of age and by people with reduced physical, sensor and mental capabilities, as well as by people with insufficient experience and knowledge provided they are supervised or instructed in safe operation of the appliance and understand the related risks. Children should not be allowed to play with the appliance. Cleaning and user maintenance operations must not be carried out by children without supervision.

• CAUTION: Some of the appliance parts may get very hot during operation and thus cause burns to users. In case there are children and vulnerable people in the room, special attention should be paid.

• WARNING: In order to avoid overheating, do not cover the fireplace!

• The appliance should not be placed right under a socket.

• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

• This appliance shall be used only for the purpose it has been designed and intended for, i.e. heating of domestic premises. The appliance is not intended for commercial purposes. Every other use is to be considered improper, and therefore dangerous. The manufacturer doesn’t bear responsibility for damages arising from improper and irrational use. Non-adherence to these instructions would render the warranty invalid!

• Before switching on the appliance, check if the voltage indicated on its technical plate corresponds to the voltage of the electricity supplied to your place.

• Do not leave your place while the appliance is operating: ensure that the power switch knob is switched to OFF position. Always disconnect the power plug from the socket.

• Keep inflammable objects, such as furniture, pillows, bedding, paper, clothes, curtains, etc. at a distance of at least 100 cm away of the electric fireplace.

• Do not operate the appliance in areas of use or storage of combustible substances. Do not operate the appliance in areas of combustible media (for example in close proximity to inflammable gases or aerosols) – there is great risk of explosion and fire!

• Do not insert and do not allow foreign objects to enter the ventilation openings (inlet and outlet) because this will cause electric shock, fire or will damage the appliance.

• This appliance is not suitable for animal breeding and it is intended for domestic use only!

• The most common cause of overheating is fluff and dust deposits in the appliance. Clean the ventilation openings regularly with a vacuum cleaner. Before that disconnect the power plug from the mains.

• Never touch the appliance with damp or wet hands
  – this may be dangerous to for your life!

• The power socket must be easily accessible all the time in case the power plug has to be disconnected as fast as possible! Never pull the power cord or the appliance itself in order to disconnect it from the mains.

• ATTENTION! Outgoing air gets hot during operation (up to more than 100°C).

• If the appliance is damaged or does not work properly, stop it and do not repair it yourself. For any kind of repairs call for assistance an after-sale service centre. This is the place where you will have your broken part replaced with an original one. Non-adherence to this instruction will compromise the appliance safety.

• If you decide to stop using such kind of appliance, it is advisable to render it unusable by cutting its power cord after disconnecting it from the mains. It is advisable all possible risks related to the appliance to be secured, especially in relation to children that may play with out-of-use appliances.

• Never keep the appliance unnecessarily switched on. Disconnect it from the power socket when you do not intend to use it for a long period of time.

• Warning: Do not use this appliance with a programming device, counter or any other device which can automatically switch it on because if the appliance is covered or improperly positioned this may cause fire.

• Position the power cord in such a way that it does not obstruct the free movement of people and cannot be stepped on! Use only approved extension cords which are suitable for this appliance, i.e. have got a conformity sign!

• Do not bend the power cord and do not stretch it over sharp edges, do not position it over hot plates or open flames!

• Never use the electric fireplace in close proximity to a bathroom, a shower cabin or a swimming pool!

• Do not lift the fireplace by the front glass.

PACKING

• After unpacking the appliance, check if all its elements are included in the packing and that it has not been damaged during transportation! In case damage or incomplete delivery is found, contact your authorized retailer!
• Do not throw away the original packing! It could be used for storage and transportation purposes in order to avoid damages during transportation!
• Disposal of packing materials should be done in the appropriate way! Children should be prevented from playing with polyethylene bags!

INSTALLATION INSTRUCTIONS

Note: The electric fireplace is intended only for wall-mounted operation!

• The fixed elements in the packing are of small size and they should be kept away from small children. We recommend all elements to be put in a small box and to be stored away from children.

• Small children should be prevented from playing with polyethylene bags – there is risk from suffocation. We recommend disposing of them right after emptying them.

• Do not connect the electric fireplace until it has been well-mounted to the wall and you have read all important instructions above.

• The minimum distances in front of, above and under the fireplace shall be observed as indicated above and shown below.

• During mounting you should be careful about
  not damaging the cables in the walls. Please pay attention when drilling holes in the walls. Danger from electric shock!

• The appliance is designed to be permanently wall-mounted at height of minimum 300 mm from the floor. The bearing clamp shall be in horizontal position. The power cord is in the bottom right corner of the fireplace.A height of 600 mm from the floor is recommended for optimal visualization of the flame effect (1 for recommended dimension for mounting).

• For optimal visualization, mark the positions of the top 5 screws for wall-mounting in accordance with the recommended dimension for mounting
  Openings with 6 mm drill bits

• Mount the bearing clamp to the wall by the screws.

• Carefully lift the fireplace upwards so that the upper rear edge of the fireplace to lie over the bearing plate fixed on the wall and position it centrally.

• Carefully press the fireplace to the wall.

• Mark the position of the bottom openings  remove the fireplace, ensuring that the lower mounting plate is turned and will not be an obstacle.

• Drill the openings for the bottom holes and fix on the wall.

• Place the fireplace on the bearing clamp, fixed on the wall, and turn the clamp to fix the lower part. Use the securing screw to permanently mount the fireplace to the wall and to protect it from unhanging.

• Unpack the log or the pebbles from the polyethylene bag and place them along the light-emitting element in the configuration and position you wish.

• Place the front glass ensuring that each pair of grooves from both sides are properly aligned towards to supporting axes. Usually, two people can accomplish this operation.

• Note: During appliance operation in areas with very low level of background noise, it is possible specific sound to be heard which is related to the flame effect. This is normal and should not be considered worrying. Thank you for choosing the electric fireplace – WEF200SRELW TR. This is a product providing heating in winter in power ranges of 1000W or 2000W, depending on the consumers’ needs for comfortable room temperature. If operated and taken care of properly in accordance with these instructions, the appliance will provide you with many years of useful operation.

USING THE FIREPLACE

• The fireplace can be operated by the switching knobs located in the upper right part of the appliance or by the remote control.
  LED DISPLAY

• Temperature and serial number display

• Normally it displays the room temperature; while setting the temperature, the temperature being set is displayed;

• When setting the timer, serial number is displayed.
  Time display

• Normally it displays the current time; while setting the timer, the time being set is displayed.
  Timed starting and timed shutdown

• It is displayed while setting the timer, and it is used in combination with serial number setting. E.g.,

  • means the startup time for setting 5 is 23:40;
  • means the shutdown time for setting 5 is 6:10.z

• Flame brightness
  It displays the current brightness of the flame, which ranges from one to five positions. This icon is not displayed for color flame.

REMOTE CONTROLLER AND CONTROL SWITCH

BOOT STEPS

1. Connect the power
2. Turn on the power switch
3. Press the control switch or „ON/OFF“ key of the remote controller to start up

HEATING DEVICE

1. Press the 1000W button to can control the low-level heating of the fireplace and stop heating

Press the 2000W button to can control the highlevel heating of the fireplace and stop heating.
AUTOMATIC HEATING

1. Press IC button on the remote controller to start or exit the automatic heating.
2. When turned on, the fireplace can automatically change the heating mode depending on the set temperature and the room temperature.

During a timed starting process, it is possible to start heating ahead of schedule.

MONOCHROME FLAME FIREPLACE WITH ADJUSTABLE FLAME BRIGHTNESS

1. Method one: Hold down the control switch О/I button, the flame brightness changes, release the button when the desired brightness is reached.
2. Method two: press „DIMMER“ button on the remote controller, the flame brightness may change step by step with each press of the button.

SETTING THE DATE AND TIME

1. Settings are done on the remote controller;
2. Press „DATE TIME“ button, then press the or , key to select the date;
3. Press „DATE TIME“ button again, then press the „+“ or „-“ to set the hour
4. Press „DATE TIME“ button again, then press the „+“
5. or „-“ to set the minute
6. Press „OK“ button to complete

TEMPERATURE SETTING
The default set temperature is 20°C, press „+“ or „-“ on the remote controller to set the temperature, which ranges from 15 to 30°C, and this is the normally set temperature (the timer is off )

TIMER SETTING

1. Description of setting
   There are up to 10 items for timer setting
   Each item of setting has its date, power-on time and shutdown time
   The max. duration of each item of setting is 23 hours 50 minutes
   The set date for each item can be any day or days of a week
   The date in each item of setting represents the date of power-on time
   If the shutdown time being set falls on the second day, it is unnecessary to set the date – you just set the shutdown time.

2. Steps to view the timer setting
   Press the „TIMER SET“ button
   Press the „+“ or „-“ to check the power-on time set by the timer item by item
   For checking the shutdown time, press the „ “ button.
   Press the „+“ or „-“ to continue viewing
   For deleting the current item of setting, press „C“ to delete.

3. Time setup steps for timer setting

• Select the settings
  Press the „TIME SET“ button, and the serial number of setting starts blinking
  Press the „+“ or „-“ to change the serial number until you get the serial number of setting that you need to set or modify.

• Select date
  Press „TIME SET“ button once again, and the cursor on the left side of date starts blinking
  Press the or keys to move the cursor to the corresponding date, press the „+“ to add the corresponding date, or press „-“ to delete the date until you have completed the selection of all dates.

• Set the start time
  Continue to press the „TIME SET“ button, the hour starts blinking
  Press the „+“ or „-“ to adjust the hour
  Continue to press the „TIME SET“ button, the minute starts blinking
  Press the „+“ or „-“ to adjust minute.

• Set the shutdown time

  • Then press the „TIME SET“ button, the display is off, and the hour starts blinking
  • Press the „+“ or „-“ to adjust the hour
  • Continue to press the „TIME SET“ button, the minute starts blinking
  • Press the „+“ or „-“ to adjust minute.

• Set temperature

  • Then press the „TIME SET“ button, and the temperature set starts blinking. At this moment, the temperature displayed is normally set temperature, which can be adjusted by pressing „+“ or „-“
  • (VI) Press „TIME SET“ button to continue setting, and press „OK“ complete the setting

• TIME SWITCH

  • „TIME ON/OFF“ is to control the timed opening and closing
  • Restart the machine after power is cut off, the original setting is kept, but the current date and time must be reset
  • Note: The device shows the temperature around the location of the sensor and is not a means of accurately measuring the ambient temperature.

PROTECTION FROM OVERHEATING

This appliance is equipped with safety thermal disconnection device, which is actuated at high temperature (resulting for example from blocking of the outlets for outgoing air). For safety purposes the thermal disconnection device will not be automatically restarted. In order for it to be restarted, you need to take the power cord out of the socket, wait for about 10 minutes and then put the plug in the socket again. Normally the appliance will start operating, but if this doesn’t happen, you need to check the inlet and outlet openings. If everything is normal with them (and the appliance has been regularly cleaned from dust), please contact the service center in your location.
Note: To avoid the risk of involuntary restart of the thermal disconnection device, you should not connect any external starting devices such as timers, series connection switches which provide regular switching on and off of the appliance for the sake of convenience.

CLEANING

• It is compulsory first to switch off the appliance and disconnect its power cord from the socket on the wall. Before starting to clean the electric fireplace you should wait until it cools down.
• Clean the body of the appliance with a damp cloth, vacuum cleaner or soft brush.
• Never immerse the appliance into water – there is risk for your life from electric shock!
• Never use petrol, thinner or coarse abrasive products for cleaning because they will damage the surface coating of the appliance.

STORAGE

• Before putting away the electric fireplace let it cool down after disconnecting it from the power socket.
• Use the original packing for storing the electric fireplace if it will not be used for a certain period of time. The product is protected from excessive dust and dirt when it is kept in its original packing.
• Never put a hot appliance into its packing!
• the product is necessary to be stored at a dry place away from direct sunlight.
• It is explicitly forbidden to store the appliance in wet or damp premises.

THE PRODUCT PACKING SET INCLUDES

TECHNICAL CHARACTERISTICS OF THE APPLIANCE

Lightening – LED system (no replacement parts)

Environment protection instructions
Old electric appliances contain valuable materials and therefore should not be disposed of as domestic waste! We ask you for your active cooperation to protect the resources and the environment by submitting your appliance to organized buy-back stations (if there are such)

TABLE 2: INFORMATION REQUIREMENTS FOR ELECTRIC LOCAL SPACE HEATERS
Model identifier(s): 1.WEF200SRELW TR 2000W/220-240V~ 50Hz

charge control, with room and/or outdoor temperature feedback heat charge control, with integrated thermostat| [yes/no]
Auxiliary electricity consumption| | | | Fan assisted head output| [yes/no]
At nominal heat output| elmax| 0.014| kW| Type of heat output/room temperature control (select one)| –
At minimum heat output| elmin| 0.014| kW| Single stage heat output and no room temperature control| [no]
In standby mode| el SB| Stand by 0.00048| kW| Two or more manual stages, no room temperature control| [no]
| | | | With mechanic thermostat room temperature control| [no]
| | | | With electronic room temperature control| [no]
| | | | With electronic room temperature control plus day timer|   [no]
| | | | With electronic room temperature control plus week timer|   [yes]
| | | | Other control options (multiple selections possible)|
| | | | Room temperature control, with presence detection| [no]
| | | | Room temperature control, with open window detection|

[no]
| | | | With distance control option| [no]
| | | | With adaptive start control| [yes]
| | | | With working time limitation| [no]
| | | | With black bulb sensor| [no]

References

• TESY Homepage

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>