TESY HL-246VB W Fan Heater Instruction Manual

TESY HL-246VB W Fan Heater

IMPORTANT SAFETY PRECAUTIONS

WARNING!

• Please read this manual before operating the appliance and keep it at a safe place for future reference. In case the appliance is obtained by a new owner, it should be transferred together with its manual.

• CAUTION: Children under 3 years of age should be kept away from the appliance unless they are under constant supervision. Children from 3 to 8 years of age are allowed to operate the on/off button ONLY, provided that the appliance is installed and ready for operation and such children have been supervised and instructed in safe operation of the appliance and they understand all related risks. Children from 3 to 8 years of age MUST NOT: connect the plug to power sockets, make adjustments, clean it or carry out user maintenance operations. This appliance can be used by children older than 8 years of age and by people with reduced physical, sensor and mental capabilities, as well as by people with insufficient experience and knowledge provided they are supervised or instructed in safe operation of the appliance and understand the related risks. Children should not be allowed to play with the appliance. Cleaning and user maintenance operations must not be carried out by children without supervision.

• CAUTION: Some of the appliance parts may get very hot during operation and thus cause burns to users. In case there are children and vulnerable people in the room, special attention should be paid.

• WARNING: In order to avoid overheating, do not cover the appliance!

• The appliance should not be positioned right under a power socket!

• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

• Before connecting the fan heater, you should check if the voltage on the technical information plate corresponds to the voltage of the main electrical system of the place of use /at home or in the office/. The appliance is intended for the voltage, shown on the technical information plate.

• HL-246VB W fan heater must be installed in accordance with the good professional practices and in accordance with the legislature of the particular state (Electricity Directive of EU and requirements for special installations and places of installation including bathroom or shower box HD60364-7-701:2007(IEC 60364-7- 701:2007)).

• The heater is classified as class II and is provided with IP24 water protection. For that reason it must be mounted in position (VOLUME) 2. That prevents the chance of reach to the control board (switch and thermostat) of the fan heater by a person who is in a shower or in a bath. Minimum permissible distance between the appliance and a water source must not be less than 1 meter! The appliance is to be mounted on a wall only
  

• This appliance must be used only with its main function, which it was intended for, i.e. heating of domestic premises. Every different usage is considered incorrect and hence dangerous. The manufacturer does not assume responsibility for break-downs, caused by incorrect and unreasonable usage. Non-adherence to the safety precautions will render the guarantee invalid

• Do not leave your home, while the appliance is turned on: assure that the switch is in position OFF(0) (turned-off) and the thermostat switch is in position – minimum. Always disconnect the plug of the device from the socket.

• Keep inflammable objects as furniture, cushions, bedding, paper, clothes, curtains etc. at a distance of minimum 100 cm away from the fan heater.

• Do not use the device in areas of usage and storage of inflammable substances. Do not use the device in combustible areas /for example near inflammable gases and aerosols/ – there is a great risk of explosion and fire!

• Do not insert or allow any objects to get into the ventilation openings (inlets and outlets), because that can cause break-down of the appliance or any other damages.

• The appliance is not suitable for animal breeding and is intended only for domestic use!

• Keep the air outlet free from any objects: you should keep a clear distance of at least 1m in front the heater. Do not allow any objects to get into in the air inlet or outlet because that can cause electrical shock, fire or damage of the heating element.

• The most common reason for over-heating is the accumulation of dust and dirt in the appliance. You should clean regularly ventilation openings with a vacuum cleaner. Before cleaning you must disconnect the appliance from the mains. Keep the fan heater always clean.

• You should never touch the appliance with wet or moist hands – there is danger for your life!

• In order to disconnect the plug from the socket outlet when necessary the socket should be accessible all the time!

• You must never pull the electric cord or the appliance itself when disconnecting from the mains

• Warning! The air outlet gets hot when the appliance is operating (more than 80°С).

• Do not cover the appliance. If the appliance is covered there is danger of overheating.

• The electrical system to which the appliance is connected must be provided with automatic safety fuse. The distance between the sockets and the appliance (in turned-off state) must be at least 3mm.

• Grounding is forbidden! After unpacking and before use you must check if the mechanical parts and their gear are in a good state. If you have any doubts you should not use the appliance and search advice from a qualified electrician.

• If the appliance is damaged or not functioning properly you must stop it and not try to repair it yourself. For any type of repairs you must consult the Service Center for post-sale help. There you will have your damaged part replaced with an original spare one. Not obeying this instruction will compromise the appliance safety.

• If you decide to stop using an appliance of that kind it is recommended to make it unusable as you cut the electric cord, after you have disconnected it  from the mains. It is also recommended all hazards, related to the appliance to be checked. That is very important if there is a chance the discarded appliance to be used for play by children.

• You should never keep the appliance unnecessarily plugged-in. Disconnect the appliance from the mains if you do not intend to use it for a long time.

• In order to avoid any overheating of the electric cord it is recommended to unreel the whole electric cord.

• Warning: Do not use this appliance with a programmer, counter or another device which can automatically turn it on because if the appliance is covered or incorrectly positioned there is a danger of fire.

• Place the electric cord in such a way that it does not hamper the movement of people and not to be stepped on! You must use only approved connection blocks, which are suitable for the appliance, i.e. there is a sign of compliance!

• The electric cord must not be in touch with the hot parts of the appliance!

• You must never move the appliance by pulling it by its electric cord. You must never use the electric cord for moving of other objects.

• Do not reel the electric cord round the appliance! Do not use the appliance with its electric cord reeled – this is also valid if a cable drum is used!

• Do not press the cord and do not stretch it by sharp edges. Do not place the cord over hot plates or in open fire!

PACKAGE

• After unpacking the appliance you should check if it is not damaged during transportation and if all the components are included! In case that you find out any damage or incomplete package you should connect with your authorized retailer!
• Do not discard the original packing box! It could be used to store the appliance during transportation in order damages to be avoided!
• The disposal of the packing material should be done in the appropriate way! Children should be prevented from playing with the polyethylene bags!

MOUNTING ON A WALL

1. Please ensure that the walls of the installation location without wires, pipes, etc., to ensure that the device can be securely mounted on the wall
2. The appliance is intended only for vertical wall mounting! Floor or ceiling mounting is forbidden!
3. Never position the appliance right below a socket outlet!
4. The appliance should be assembled and connected by a qualified electrician. The installation process should be isolated from the mains before electrical connection works are to be done.
5. Position the power cord so that it does not hamper free movement of people and not to be stepped on! Use only approved extensions, which are proper to the appliance, i.e. they have a compliance sign!
6. The power cord should not be in touch with hot parts of the appliance
7. Do not use the appliance in rooms smaller than 4 square meters.

FIXING TO THE WALL

Warning! To prevent damage or the risk of fire:

• Ensure a sufficient distance from the wall (min. 25 cm at the sides), ceiling (min. 20 cm), floor (min. 1.5 m), fixtures (min. 1 m) or other appliances (min. 1 m).
• Only use the fastening bracket provided for fixing the appliance to the wall, to ensure the necessary distance from the rear wall.

1. Selecting a place to install the appliance
   • on a wall that is sufficiently strong
   • which is somewhat sheltered, so that the appliance is not shaken excessively by strong winds;
   • at least 1 m from people, animals and plants;
   • which complies with the distances shown in the sketch below
   
   Note: The appliance is manufactured entirely of rust-proof materials and can be exposed to normal environmental impacts

2. Mark the drill holes according to the diagram:

Drill 2 holes with diameter 6 mm in the wall, The drilling depth is approx. 40 mm

3. Insert a wall plug into each hole.

4. Screw two long screws into each hole. Allow the head of the screw 5mm so that the appliance can be hung on these.

5. Hang the appliance on the screws.
   Mark the drill hole for screwing the fastening bracket
   

6. Take the appliance off the wall and drill the corresponding hole.
   • Using a 6 mm bit, drill a hole to fit the wall plug.
   • Insert a wall plug.
   
   7. Hang the appliance again on the screws.
   8. the fastening bracket securely to the wall using a screw.
   

We thank you for choosing HL-246VB W fan heater. This is a product, which provides heating at 1000W or 2000W in cold weather in accordance with the desired temperature conditions in the room. The appliance will provide long- life service if being correctly maintained and taken care of in accordance with the manual.

OPERATING

Note: As the appliance and heating elements are supplied with a thin film of grease, there might be a small amount of smoke and odour the first time the appliance is used. This is not harmful and will stop after a short while. Please ensure in the meantime that there is sufficient ventilation)

CONTROL PANEL

Note: The screen will be locked when the device is on or in any mode if without any operation after 1 minute. Screen will display Unlock the screen Pressing and holding in 3S

HEATING OPERATION

• Press the button . The device switches on with Fr manual mode. On the display appears F

– Selecting the temperature

1. Use the button “+” to increase the set temperature up to a maximum of 35°C.
2. Use the button “–” to reduce the set temperature down to a minimum of 10°C.

The set temperature is shown on the display.

The heater switches off as soon as the room reaches the set temperature.

If the room temperature falls below the set temperature, the heater and fan switch on again automatically

Note: The device shows the temperature around the location of the sensor and is not a means of accurately measuring the ambient temperature.

-Setting the clock

1. To switch the clock, press the “C/M” button.
2. The display shows and the hours flash.
3. Press the “+” button to increase the hours.
4. Press the “-” button to reduce the hours.
5. Press the “C/M” button again. The minutes flash.
6. Press the “+” button to increase the minutes.
7. Press the “-” button to reduce the minutes.
8. Press the “C/M” button again. The days flash.
9. Press the “+” button to increase the days.
10. Press the “-” button to reduce the days

– The appliance has a timer with which you can set the required operating time. The appliance switches off automatically once the operating time has expired

1. To switch the timer, press and hold the “C/M” button for 3 sec.
2. The display shows and the hours flash.
3. Press the “+” button to increase the hours.
4. Press the “-” button to reduce the hours.
5. To switch off the timer, press and hold “C/M” button until  is no longer displayed.

• Programming modes

To switch on the programming mode, press the “P/PRO”.
The display shows

The appliance has seven working modes between P1 and P7

Press the “+” and “-” button repeatedly until desired working mode is shown on display

– Comfort mode .

As soon as the temperature in the immediate vicinity of the appliance drops significantly below 9°C, the heating automatically switches on.

As soon as the temperature rises to above 35°C, the heating switches off and display shows room temperature again.

Working power 2000W

– ECO mode

As soon as the temperature in the immediate vicinity of the appliance drops significantly beloAs soon as the temperature rises to above 35°C,
the heating switches off and display shows room
temperature again.w 7°C, the heating automatically switches on.

As soon as the temperature rises to above 35°C, the heating switches off and display shows room temperature again.

Working power 1000W

– Frost protection mode

The device now will switch on if the room temperature drops below 7°C.

– POWER OFF mode

Power off

– Programming modes (Manual)

Pressing and holding “P/PRO” for 3 sec. displays ”PROG” during P1-P7 working mode to setting.

1. Pressing “PROG” to setting the time(1-24H) in each mode
2. Pressing” C/M” to setting the mode in each time.
3. Pressing “+” and “-” to setting different temperature what you want under Comfort and ECO mode.
4. display“- -”when setting OFF
5. Anti-forst in 7°C unadjustable
6. You can choose any mode during P1-P7 in any hour after setting

SETTING Demonstration:

0-6H in mode:Comfort mode
Setting different temperature in each hour

6-12H in mode:Anti-forst
Fix temperature in 7°C

12-18H in mode: “ECO” mode
Setting different temperature in each hour

18-24H in mode: OFF

AU mode

In the manual programming modes, press the “P/PRO” button, the flash.

1. Use the “+” button and “-” button to set the AU mode.

2. Press the “P/PRO” button until the “PROG” appears
   in the display.

3. Use the “+” button and “-” button to set the program number.

4. Press the “C/M” button, the days flash.

5. Use the “+” button and “-” button to set the days.

OPEN WINDOW FUNCTION

Open window Function: Activated by pressing .
When the device works and the environment temperature change in a big range the appliance will shut off automatically. Pressing again will cancel this function.

Note: After 5 seconds the preset is shown continuously in the display and the settings are taken over.

OVERHEATING PROTECTION

The in-built overheating protection automatically turns the appliance off in case of an error! In that situation the plug must be disconnected from the mains and the control switch put in position “0”. After a short period of cooling the appliance is ready for operation (in about 10-15 minutes)! If that error is repeated – consult an authorized service at your location!

CLEANING

• You must first turn off the appliance and disconnect its plug from the socket. Do not use abrasive detergents
• Clean the body with wet cloth, vacuum cleaner or a brush!
• You must never submerge the appliance under water – there is life danger!
• If the appliance should not be used for a certain period of time it must be secured from excessive dirt and dust by placing it in its original package.
• You must never place the hot appliance in its package!

Instructions for environment protection
Electric appliances out of use contain valuable materials and hence must not be disposed in domestic dumbs! We kindly ask you for cooperation and active role in preservation of natural resources by disposing the appliance to the organized buy-back locations (if there are any).

TABLE 2: INFORMATION REQUIREMENTS FOR ELECTRIC LOCAL SPACE HEATERS
Model identifier(s): 1.HL-246VB W 2000W/230V~ 50Hz

TESY Ltd – Head office
1166 Sofia, Sofia Park,
Building 16V, Office 2.1. 2nd Floor
PHONE: +359 2 902 6666,
FAX: +359 2 902 6660,
office@tesy.com

References

• TESY Homepage

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>