JIMMY WB55 Anti-Mite Vacuum Cleaner User Guide

WB55 Anti-Mite Vacuum Cleaner
User Guide

Products Installation

Unpacking
Open the package, take out all accessories and machines from the package, and save the outer package for the purpose of future maintenance and repair.

Parts Name

Packing List

Use of the Product

Insert the plug into the socket, and press the on/off button, the machine is in strong mode and the strong indicator lights up. Press the mode button to switch the low mode and the low indicator lights up.
Press the on/off button again, and the machine stops working(Figure 1)
Notice: For safety reasons, the UV light only works within 3cm above the object as well as less than 30 inclination degrees. Otherwise, the UV light will automatically turn off.

Cleaning and Maintenance

Dust Cup Cleaning
Turn off the machine and unplug the power cord. Then press the release button and lift upward (Figure 2).

Hold the dust cup and dust cup cover separately, twist the dust lid anticlockwise (Figure 3), and remove it from the dust cup to clean (Figure 4).

Filter and Cyclone Cleaning

Hold the cyclone in one hand, pinch the “UP” logo with the other hand, and take out the filter (Figure 5). Do Not tap the filter on the reverse side in case of a filter clog(Figure 6).
lean the cyclone metal filter with the attached mini brush(Figure 7).

After cleaning the filter, remove the two screws on the cyclone cover with a screwdriver to separate the cyclone cover from the cyclone to clean the internal air duct. After cleaning,  assemble parts in reverse order. (Figure 8).

After cleaning dust cup, filter and cyclone, assemble in reverse order. Rotate the dust cup cover assembly into the dust cup. After hearing a “click” the dot mark is aligned with the lock position that is assembled in place.

Notice:

1. Do Not miss the filter!
2. Use water or neutral reagents to clean the dust cup and wipe with dry cloths. Do not wash the filter until it is necessary. Make sure the filter and dust cup are completely dry before another use.

Brushroll cleaning and installation

Turn off the machine and unplug the power cord, rotate the right lock knob anticlockwise with your hand from the locked position to unlock position (Figure 9) to remove the brush roll to clean up(Figure 10).

After brush roll cleaning, insert the brush roll from the hole on the right. Make sure the left plug of the brush roll is fully snapped into the belt(according to Figure 11) to lock the brush roll on the window.
Otherwise, the brush roll cannot be locked.
Notice:
for safety reasons, please turn off the machine and unplug the power cord before cleaning the brush roll.

Maintenance and storage

Please clean the dust cup and filter after each use for further use. It is recommended to replace a filter after 30-50 hours of working time(depending on the specific situation) for better use.

Any paper, lead glass, or plastic will greatly affect the effect of UV light. Please wipe and clean the UV tube regularly for better use.

Put the machine in a cool and dry place if the machine is to be idled. Do Not leave it in direct sunlight or a humid environment.

Cautions

Please read this instruction manual carefully before use and keep it properly for future use.
Never leave the machine working without supervision.
Please turn off the power switch and unplug the power cord if the machine is to be idled. Do Not unplug the power cord with a humid hand in case of electric shock.
Cut the power source in maintenance or off-service.
Keep the power cord away from sharp objects and do not drag the cord to move the machine in case of cord damage.
For safety reasons, please do not use the product to clean hot objects such as carbon, cigarette butts, sharp objects such as broken glass, corrosive liquids, or flammable and explosive materials such as gasoline and alcohol. Otherwise, it may cause product damage or fire.
Do not use this product to clean water or wet dust. Do Not operate it in humid places (such as a bathroom, toilet, laundry room, etc.) to avoid malfunction.
Do Not place the machine near heating appliances or expose it to direct sunlight in case of a fire hazard.
Keep this product beyond the reach of special individuals such as children without adult supervision.
Do Not operate this machine with the suction port blocked in case of product damage.
The product has UV light, for safety reasons, Do Not look at the bottom of the machine when the power is on in case of ultraviolet rays harming.
Do Not apply this product to plants. Excessive use of UV may cause object damage.
Do Not sit on this product in case of personal injury and product damage.
Do Not remove the brush roll cover or force the cover outward when the machine is powered on for safety reasons.
This product can ONLY be used for the cleaning of textiles such as mattresses, blankets, pillows, sofas, etc.
If the power cord is damaged, please ask for the professional help of the manufacturer and other professionals for safety reasons.

This product can ONLY be used for the cleaning of textiles such as mattresses, blankets, pillows, sofas, etc.
If the power cord is damaged, please ask for the professional help of the manufacturer and other professionals for safety reasons.

Trouble Shooting

If the fault remains after adopting the following solutions, contact after- sale service or local distributor immediately.

firmly.
No power on the socket.| Check the socket.
The power switch is not pressed.| Press the On/Off button.
Low suction power| The suction port clogged.| Clean up the suction port.
Dust accumulation on the filter.| Clean up the filter.
Dust accumulation on cyclone.| Clean up the cyclone.
Dust accumulation on the filter.| Clean up the filter.
UV tube failure| The UV function is automatically off for safety reasons or weak reflection of the object.| The UV function operates on the condition of less than 5CM height from the object.
The machine operates in the same position for a long time.| Move the machine forward and backward
The machine is placed upright.| The machine tilted no more than 30 degrees.
The sensor window is contaminated.| Clean the sensor window with a half-dry cloth.
UV light damage.| Contact after-sale service.
Automatically turned off| Dust cup full.| The machine will automatically turn off to prevent the motor under long operation. If the machine is automatically turned off, please clean up the dust cup and filter, unplug the power cord and reuse it after 2 hours.
The suction port clogged.
Filter blocked.
Brushroll failure| Brushroll tangled with foreign matter.| Remove the cover and clean up the brush roll according to the user guide.
Belt broken.| Remove the cover according to the user guide and check the belt. If broken, contact after-sale to repair.

Product Specification

Parameter

Circuit Diagram

Manufacturer Information

215009,China

Disposal

The machine, accessories, and packaging should be sorted for environmental- friendly recycling.
Do not dispose of the machine into household waste!
Only for EC countries: According to the European Guideline 2012/19/EU, machines that is no longer usable, and according to the European Guideline 2006/66/EC,  defective or used battery packs/batteries, must be collected separately and disposed of in an environmentally correct manner.
Subject to change without notice.

Warranty Information

This product enjoys one year warranty for the machine service starting from the date of purchase.
Excluded from the guarantee is normal wear, commercial use, alterations to the appliance as purchased, cleaning activities, consequences of improper use or damage by the purchaser or a third person, and damage, that can be attributed to external circumstances or caused by the batteries.

NOTE
____

Contact us -we’ll get back within 1 business day.

Web:www.jimmyglobal.com
Email:support@jimmyglobal.com

References

• JIMMY cordless vacuum, JIMMY vacuum cleaners, H9 Pro powerful vacuum, JIMMY F6 hair dryer -JIMMY

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>