JIMMY HW8 Cordless Vacuum Washer Instruction Manual

HW8 Cordless Vacuum Washer
Instruction Manual
Cordless Vacuum&Washer

Products Installation

Parts Name

Packing List

| Mainbody| Handle| Charging base| Adaptor| Cleaning brush| Cleaning Shampoo| Battery pack| Brushroll| User instruction
---|---|---|---|---|---|---|---|---|---
HW8| 1| 1| 1| 1| 1| 1| 1| /| 1
HW8 Pro| 1| 1| 1| 1| 1| 1| 1| 1| 1

Product assembly and disassembly

Note: Cut off electricity before product assembly and disassembly.
Handle assembly and disassembly
Insert the handle into the main body vertically until a“click” sound is heard. Make sure the handle is firmly locked. To remove the handle, press the back covers latch to open back cover, use a tool like a screwdriver to insert into the hole, and pull out the handle upward.(Fig 1) Note:

1. Do not move the machine by dragging the looped wire to avoid damaging the wire.
2. During assembly, the handle metal tube side with latch needs to face the machine back. (Fig 1)

Assemble battery pack
Remove the back cover, and slide the battery pack along the slot into the main body until to the bottom. Clip back cover left and right clips into back body slots. Push back cover latch to lock back cover until a “click” sound is heard. (Fig 2)

Pick and place machine
To put the machine back to the charging base, hold the machine handle to lift the machine, let the floorheaddrop down, aim to charge the slot on the bottom of the machine to the charging pins on the charging base, and put the machine into the charging base. To use the machine, hold the machine handle and lift out the machine from the charging base.(Fig 3) Disassemble and assemble the dirty water tank
To take off the dirty water tank, hold the machine with one hand and hold the dirty water tank with another hand, press the dirty water tank release button to remove the dirty water tank. To assemble the dirty water tank, place the dirty water tank bottom into the main body, and push dirty water tank towards the main body until a “click” sound is heard.(Fig 4) Disassemble and assemble a clean water tank
To take off the clean water tank, press the clean water tank release button, and the clean water tank will pop out from the back body, remove the water tank. To assemble a clean water tank, Place the cap on the clean water tank bottom into the water inlet slot on the back body, and press the clean water tank until a “click” sound is heard.(Fig 5)![JIMMY HW8 Cordless Vacuum Washer

• fig 5](https://manuals.plus/wp-content/uploads/2022/08/JIMMY-HW8-Cordless- Vacuum-Washer-fig-5.png) Disassemble and assemble brush roll window and brush roll

  1. To take off the brush roll window, put your finger on the brush roll window holder position and pull upward to remove the brush roll window. To assemble the brush roll window, align the clips on two sides of the brush roll window with the slots on two sides of the floorhead. Press the brush roll window until a “click” sound is heard.
  2. Disassemble/assemble brushroll: Pull out brush roll left cap with finger to take brush roll out. Hold brush roll cap, slide brush roll left side into gear, place brush roll into the nozzle.(Fig 6)

Products USE

LED screen

1. Lights: White color, shows machine Max and Standard mode(Full lights in Max/Half lights in Standard).
   HW8: Brushroll rotating speed is different in Max and Standard mode.
   HW8 Pro: Vacuum suction power is different in Max and Standard mode.

2. Battery power digital and percentage display: Displays current battery power left.

3. Battery power icon display: Battery power warning(Lights are white when battery power is higher than 20%, lights turn red and blink when battery power is lower than 20%).

4. Dirty water tank full indicator: When the water in the tank reaches the MAX line, the indicator will blink to remind the user to drain the dirty water tank.

5. Clean water tank empty indicator: When the water tank is empty, the indicator will blink to remind the user to add clean water.

6. Self-cleaning indicator: When the machine is in self-cleaning mode, the indicator will blink to remind the user that the machine is under self-cleaning.

Fill up the clean water tank

1. Press the clean water tank release button to take off the clean water tank.
2. Turn the clean water tank upside down, turn the cap clockwise to open, and fill in clean water(Below 50℃ )until the MAX line.
3. Tighten the clean water tank cap and make sure it is tight.
4. Assemble the clean water tank into the main body until a “click” sound is heard.(Fig 7)

Operation of machine

1. The machine on/off button is located on top of the handle, press the on/off button to start working, and the indicator turns green. The machine can switch between Max and Standard mode by pressing the mode button. Press the on/off button to stop working.
2. Press the water spray button to spray fan shape water flow from the front of the floorhead, release the water spray button and the water will stop spraying.(Fig 8)

Note:

1. During use, the brush roll rotates normally, when the machine is in an upright position, the brush roll will stop rotating for protection.

2. Propose to only use Max mode in the very dirty area or place with much water stain. (Fig 9)
   

3. When the dirty water tank is full, the green working indicator will blink and the dirty water tank full indicator on the LED screen will also blink. The vacuum motor and brush roll motor will not stop working immediately.

4. After the machine finishes using, put it vertically on the charging base.

5. When the clean water tank is empty, press the water spray button, there is no water spray out, and the clean water tank empty indicator blinks to remind the user to add water.

6. Do not use this product to pick up foam liquid. Do not put high foam detergent into clean water.

Machine charging
Put the machine into the charging stand, connect one end of the adapter to the charging stand, and the other end to the power socket (when charging, the indicator light at the handle is red, and the display screen shows the percentage of battery power, and the light rotates in a circle; When the charging is completed, the indicator light on handle is green, the display screen shows 100% electricity, and the light at the same time is always on white). When charging, the machine should be placed on the charging base, close to the corner to avoid tripping and other injuries.
Note:

1. If the product is long idled after purchase, please use the adapter to charge the battery about every three months, to avoid affecting the battery life.
2. Do not leave the charger on the power socket all the time to prevent children from touching it by mistake.
3. When used for the first time, the capacity of the battery pack of the floor washer may not be full. Please fully charge the battery, fully discharge the battery pack, and then charge it for the second time, to improve the life of the battery.
4. For the first three times of use, it is recommended to charge the floor washer for 12 hours each time. After complete charging and discharging for three times, the floor washer can be charged according to the normal charging time.

Brushroll self-cleaning
Before self-cleaning, Drain the dirty water tank, place the machine on the charging base, insert the charger into the socket, keep at least 1/2 of the water in the clean water tank, and press the mode button for 3 seconds, and the machine will enter self-cleaning mode, the self-cleaning indicator on the LED display will blink, the front nozzle will spray water continuously for 5 seconds, then the brush roll will rotate continuously for 10 seconds for self- cleaning, and finally, the machine will run continuously for 30 seconds to pick up the dirty water into the dirty water tank, the machine will repeat this cleaning process for three-time to complete self-cleaning. And the machine enters charging mode (Fig 10) Note:
Drain the dirty water tank before and after self-cleaning.

Cleaning and Maintenance

Clean dirty water tank
When the dirty water tank is full, the water level detecting float is activated, the indicator light stays green, and the water full indicator on the display screen blinks continuously. The cleaner stops working to remind the user to clean the dirty water tank as soon as possible. After stopping work, remove the dirty water tank upper cover, pour out the dirty water and dirt in the dirty water tank, wash the dirty water tank, support frame, float, filter frame, and filter foam with clean water. Dry the above parts after washing, then put them back into the dirty water tank, and then assemble the dirty water tank into the machine to continue to use. (Fig 11) Brushroll cleaning
Hold brush roll window with a finger and pull upward to take it out. Pull the left side of the brush roll to take it out. Use a dry cloth to wipe the brush roll housing and cut off the hair tangled around the brush roll.  ash the brush roll window and brushroll in clean water. After cleaning, assemble brush roll and brush roll window back to the machine. (Fig 12) Note:
If the cleaner will not be used soon after cleaning, completely dry the dirty water tank, dirty water tank cover, filter, filter frame, brush roll, brush roll window, and machine, and then assemble the machine for storage, in order to prevent the bacteria from breeding in the humid environment and producing odor.

Maintenance and Storage

1. it is recommended to clean the dirty water tank, filter, brush roll, and brush roll window after each use. If the dirty water reaches the MAX line, please drain the dirty water tank immediately otherwise the machine cannot operate normally. After the accumulated use time of the filter reaches 30-50 hours (varies based on filter status), replace the filter to avoid affecting machine performance. The filter can be bought from a local distributor.

2. After the use of this product, place it on the charging base and ensure the product stands upright to reduce accidental contact and tilt.

3. when pack and storing the machine, if it is necessary to disassemble the battery pack, remove the back cover, hold the battery pack and pull to take it out. (Fig 13)
   

4. when the machine is long idled, place it in a cool and dry place, and avoid direct sunlight or wet environment.

Important Safety Instructions

Read all instructions and warnings before using this appliance. Failure to follow the warnings and instructions may result in electric shock, fire or serious injury.

Warning

1. The appliance is only for household use.
2. Before use, the product, check whether the local voltage is consistent with the voltage marked on the power adaptor.
3. Inspect the product before use, and stop use if the product or adaptor is damaged.
4. Use only as described in this manual.
5. This appliance cannot be used by children and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved.
6. Do not use this product as a toy. Keep this product away from the reach of children. Take care of children and make sure they will not regard this product as a toy.
7. Do not touch the plug with a wet hand.
8. Use extra care when cleaning stairs to prevent falling.
9. Do not use or disassemble or replace any component if there is damage to the power cord, plug, battery, or conductive parts. Disassembly or replacement of the components by yourself may cause electric shock or fire. JIMMY will not take responsibility. Once damaged, the product needs to be repaired or replaced by JIMMY, JIMMY’s distributor, or a qualified person designated by JIMMY to avoid injury.
10. Recharge only with the adaptor specified by JIMMY.
11. Only to use the battery pack specified by JIMMY. Use of any other battery pack may cause an explosion, injury, and or product damage.
12. If the product does not operate in accordance with the instructions, is seriously impacted, falls from a height, is damaged, or falls into the water, do not use it and contact JIMMY or JIMMY distributor.
13. Only use JIMMY-specified replacement parts or attachments.
14. Do not pull or press the cable. Keep the cable away from heated surfaces. Do not place the cable in a closed-door or pull it through a sharp edge or corner. Keep the cable away from the walking area. Do not operate the product across the cable.
15. Unplug the product when it is not used or before repairing it.
16. Do not drag the cord or carry the cord to move the product, or use the cord as a handle.
17. The product is a rechargeable electric appliance. Do not leave the machine to run unattended.
18. Remove battery pack when the product is cleaned, repaired, or long idled.
19. Do not get close to the heating appliances or be exposed to a sunshine long time, to prevent overheating and causing housing deformation.
20. Keep objects that may obstruct the air path from the air inlet and outlet to prevent machine overheating.
21. The product’s main body and floorhead have electric components, and cannot be washed under water.
22. Do not clean or disassemble brushroll cover or brushroll when the machine is powered on or under working to prevent injury.
23. Do not use the product to pick up flaming objects like burning charcoal or cigarette etc.
24. Do not use the product to pick up sharp objects like broken glass.
25. Do not use the product to pick up lime, cement, toner, gypsum powder, flour, and other ultrafine substances.
26. Do not use the product to pick up acid-base cleaning liquid, washing powder, and other corrosive liquids.
27. corrosive liquids. Do not use the product to pick up inflammable and explosive objects like gasoline, alcohol, perfume, paint, etc.
28. Do not disassemble the closed machine, and do not try to change the performance of the machine. Only getting help from the professional personnel of the manufacturer, its maintenance department or similar departments, otherwise it will cause danger.
29. Turn off the power and unplug the charger if the product is long idled.
30. Product technical specifications of this manual is based on results from lab tests of JIMMY or designated third parties. The company reserves all rights for final explanations.

About use of the product

1. This product is suitable for hard floors in an indoor environment, including waxed floors, rubber floors, tile floors, and sealed wood floors, solid wood floors,s, and another flat surfaces, use of the product on unflat ground may not achieve the best effect.
2. Do not turn on the machine before the dirty water tank and clean water tank are assembled in place according to instructions.
3. Do not shake the product up and down or collide violently to prevent dirty water from flowing into the motor; when the product is turned on, do not lift or carry the machine up and down, and do not tilt the product to one side or lay it flat on the floor to prevent dirty water from flowing into the motor.
4. Do not run the product for a long time with the float blocking the air inlet to avoid damage.
5. After using the product, clean the dirty water tank, suction nozzle, and air path and store it in a ventilated and dry place. Wet places will affect the insulation and life of electrical appliances.

About Cleaning Solution

1. A large amount of cleaning solution entering the motor may cause damage to the appliance.
2. Mix the solution with clean water according to the instructions (the ratio of solution to clean water is 1:50). It is recommended to use provided cleaning solution. Do not use a cleaning solution containing acid, alkali solution, or substances harmful to the environment.
3. Keep cleaning solutions out of reach of children. If any solution gets into the eyes, immediately flush them with clean water. If any solution is swallowed by accident, see medical care immediately.
4. Dirty water and solution disposal should comply with local environmental regulations.

About disposal of battery

1. The battery in the product contains materials harmful to the environment. Take out the battery pack from the product before disposal.
2. Turn off the product and unplug the adaptor before taking out the battery pack.
3. Handle the waste battery pack safely and properly. Do not put it into the fire, water, or soil.
4. If the disposed of battery leakage causes pollution to skin or clothes, Wash it with clean water and see medical care immediately.

Troubleshooting

Please check the following points before contacting the after-sale service.

the on/off button
The machine does not work| Brushroll is entangled| Clean brush roll
The machine does not work| Water in dirty water tank achieves MAX line| Clean dirty water tank
The machine does not work| The on/off button or mode, button is pressed at the same time as the water spray button| Release the water spray button, press on/off button or mode button separately
The machine does not work| The product is in an upright position| Release the floorhead and then the brush roll can work
weak suction| Water in dirty water tank achieves MAX line| Clean dirty water tank
weak suction| Brushroll window and dirty water tank not assembled properly| Reassemble brush roll window and dirty water tank
weak suction| Brushroll entangle| Clean brush roll
weak suction| Filter gets dirty| Clean or replace the filter
weak suction| Lower battery power| Recharge battery
Abnormal noise| Suction inlet blocked| Clean suction inlet
Abnormal noise| Water in dirty water tank achieves MAX line| Clean dirty water tank
Floorhead does not spray water| Clean water tank empty| Fill the clean water tank
Floorhead does not spray water| The water spray button was not pressed| Press the water spray button
Floorhead does not spray water| Clean water tank not assembled properly| Reassemble clean water tank
Floorhead does not spray water| The clean water tank is filled with dirty water and blocked water paths.| Do not fill the clean water tank with dirty water
Water sprays out from the air exhaust| The filter is not dry after washing| Dry the filter after washing
Water spray out from air exhaust| Water in the dirty water tank achieves MAX line| Clean dirty water tank
Water spray out from air exhaust| The product was heavily shaken or hits the wall with big force| Clean dirty water tank
Water sprays out from the air exhaust| The filter is not assembled| Assemble filter
Water spray out from air exhaust| The filter is not assembled| Assemble flotar
Water spray out from air exhaust| The filter is put to use without fully dry| Dry the filter after washing before use

Note : If the above troubleshooting guide fails to provide a solution, please contact after service or local distributor for support.

Product Specification

Technical specification

Circuit diagram

Manufacturer Information

215009, China

Disposal

The machine, accessories, and packaging should be sorted for environmental- friendly recycling.

Do not dispose of the machine into household waste!

Only for EC countries:

According to the European Guideline 2012/19/EU, machines that are no longer usable, and according to the European Guideline 2006/66/EC, defective or used battery packs/batteries, must be collected separately and disposed of in an environmentally correct manner.

Battery packs/batteries:

Integrated batteries may only be removed for disposal by qualified personnel. Opening the housing shell can damage or destroy the machine. Do not dispose of battery packs/batteries into household waste, fire or water. Battery packs/batteries should, if possible, be discharged, collected, recycled or disposed of in an environmental-friendly manner. Subject to change without notice.

Warranty Information

This product enjoys two years warranty from the date of purchase. Excluded from the guarantee is normal wear, commercial use, and alterations to the appliance as purchased, cleaning activities, consequences of improper use or damage by the purchaser or a third person, and damage, that can be attributed to external circumstances or caused by the batteries.

Web:www.jimmyglobal.com
Email:support@jimmyglobal.com

References

• JIMMY cordless vacuum, JIMMY vacuum cleaners, H9 Pro powerful vacuum, JIMMY F6 hair dryer -JIMMY

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>