WOHLER RM 300 Drain Cleaning Machine User Manual
- June 5, 2024
- WOHLER
Table of Contents
WOHLER RM 300 Drain Cleaning Machine
General Information
Operation Manual Information
This operation manual allows you to safely work with the Wöhler RM 300 Drain Cleaning Machine. Please keep this manual for your information. The Wöhler RM 300 should be used by trained professionals for its intended use only. Liability is void for any damages caused by not following this manual.
Notes
- WARNING! Not following this warning can cause injury or death.
- ATTENTION! Not following this note can cause permanent damage to the device.
- NOTE! Useful information
Intended Use
The Wöhler RM 300 drain cleaning machine is suitable for cleaning indoor and outdoor pipes Ø 40 mm to 100 mm (cable Ø 16 mm) and Ø 50 mm to 150 mm (cable 23 mm).
Transport and stoAcking
ATTENTION:
- Improper transport can harm the instrument.
- Always transport the device in the provided case in order to prevent damage or secure the unit with straps.
Fix control handle for transportation
To use the handle for transportation proceed as follows:
- Press down the contol handle (1)
- For fixation rotate the rotary lever (2) clockwise upwards.
- For loosening after transport, press the control handle (1) shortly or rotate the rotary lever (2) counterclockwise downwards.
Information on disposal
- Electronic equipment does not belong to domestic waste, but must be disposed of in accordance with the applicable statutory provisions.
Manufacturer
Wöhler Technik GmbH
- Wöhler-Platz 1, 33181 Bad Wünnenberg E-Mail: info@woehler.de
Scope of delivery
| Set | |
|---|---|
| Wöhler RM 300 | |
| 1 Cable drum for drain cleaning cable | |
| 8 drain cleaining ca- bles |
Ø 16 mm
Length: 2,3 m
| 4 cables
Ø 22 mm
Length: 4,6 m
| 1 guide hose
| 1 carrying case for drain cleaning acces- sories
****| 1 adapter with bulb auger and cable 8 mm
| Straight auger
Ø 16 mm and 22 mm
– blockages caused by textiles, paper, cellulose, kitchen waste
Initial assembly
- First mount the feet. Use the pre-drilled holes for this.
- Mount the height-adjustable feet on the side of the cable outlet.
Height-adjustable feet on the side of the cable outlet
Important information
- WARNING! Protective equipment: Guide the cable only with a suitable guide glove. Wear protective glasses depending on the application. Wear safety shoes with rubber soles (insulation) during cleaning work.
- ATTENTION! Work area: Place the drain cleaning machine on a straight and non-slip surface. Never place the mains cable in the area of the pipe cleaning cable. Always work with the guide hose.
- WARNING! Maintenance: Disconnect the electric power before making any adjustment, accessory assembly and maintenance. Keep the electric part of the machine from getting wet. Do not immerse the appliance in water when cleaning it.
- WARNING! Before switching the drain cleaner on: Avoid unintentional rotation of the cable. Put the control switch in OFF-Position before connecting the drain cleaner to the power supply. The cable must be removed completely from the holding cage before the machine is turned on. Select the appropriate auger for the blockage and the pipe diameter in order to prevent the auger from hooking and thus the cable from being thrown out of the pipe. Use a camera system to identify the cause of the blockage and select the appropriate tool.
- NOTE! Mechanical pipe cleaning should always be carried out from above, towards the block age.
- WARNING! Do not form a large working arc with the cable. The cable can overturn. The danger of jamming! The cable can jump out of the tube under tension – the risk of injury!
Specifications
Operation
Area| Outdoor and indoor pipeline
Tube Diameter| 40 to 150 mm
Spirale
Ø / Length| 16 mm / 23 m
22 mm / 46 m
8 mm / 5 m (Adapter)
Max. Length| 65 m
Coupling type| Snap Lock
Technical Data RM 300
Input Power| 570 W
Rated Voltage / Rated Frequency| 220 V
50 Hz
Rotate speed| 400 rotations per minute
Protection Class| IP 44
Weight| 18,22 kg
Components
| Component | Designation |
|---|---|
| 1 | Control handle / Carry handle |
| 2 | Fixing bolt for guide hose |
| 3 | Rotary lever |
| 4 | Control switch |
| 5 | Cable outlet |
| 6 | Feet, height-adjustable |
| 7 | Compartment for accessories |
Control switch
- Off: Stop
- For: Forward rotation, unblocking
- Rev: Reverse rotation, retrieve jammed cable
- WARNING! Prior to connection to the electric power supply check switch first for position off.
Control handle
- ATTENTION! As long as you press the handle, it is not possible to move the cable forward or backward
- Control handle down: cable rotates
PRCD-Switch (Personal safety switch)
The Wöhler RM 300 has a PRCD-switch (person-al safety switch) to protect user and drain cleaner against dangerous currents due to possibly defective electrical equipment. WARNING! Check the functionality of the switch before each use of the RM 300 as follows:
- Turn on the Wöhler RM 300.
- Press TEST If the device switches off automatically, the PRCD-switch is working and it is safe to work with the Wöhler RM 300.
- If the Wöhler RM 300 is still working after pressing the “TEST button”, disconnect the power supply immediately.
- To start normal working mode after inspection, press RÜCKSETZEN (Reset).
Operation
Working with the cable Ø 16 mm or Ø 22 mm
WARNING
- Set the control switch to “OFF” before assembling the cables, the guide hose and the augers.
- Remove the cable from the holding cage. NOTE! Make sure that the cable end with the snap-lock is guided through the cable outlet so that the clean-ing attachment can be mounted
- Pull the protection hose over the cable from behind and fix it with the locking bolt.
- ATTENTION: Always use the guide hose. It acts as a vibration-damping guide for the cable, as a dirt holder and guard, also as a safety element for the operating personnel and prevents uncontrolled banging!
- Protection hose fixed above cable, locking bolt marked by an arrow
- Select an appropriate auger and securely connect it to the cable with the snap-lock
- Fixing the auger with the snaplock
- To release the snap-lock after cleaning, insert the coupling key into the hole. The coupling key is included in the scope of delivery.
- Then pull the snap-lock apart with two hands.
- NOTE! If necessary, spray the snap-lock with a commercially available rust solvent
- Releasing the snap lock to separate the drill head from the cable
Extend the cable
Release guide hose, locking bolt marked by an arrow
Option 1:
- If you want to extend the cable, pull the end out of the guide hose.
- To do so, pull up the locking bolt on the shaft entrance and pull off the guide hose.
- Connect the next cable piece and push the entire cable length back into the guide hose.
Option 2:
- When the cable has completely run out of the machine, hold the end of the cable firmly or fix it so that it cannot disappear into the pipe.
- Push another cable piece from the front through the machine into the protective hose until only approx. 20 cm protrude from the machine.
- Connect the extension cable to the cable that is already in the tube.
Push the extension cable from the front through the unit into the protective hose
Working with the cable Ø 8 mm/adapter![WOHLER-RM-300-Drain-Cleaning- Machine-FIG-15]](https://manuals.plus/wp-content/uploads/2022/05/WOHLER- RM-300-Drain-Cleaning-Machine-FIG-15.png)
Use an adapter with the 8 mm or 10 mm cable, 5 m length, for narrow pipes or pipe bends.
- To do so, pull the cable approx. 30 cm out of the adapter magazine and push it through the shaft.
- Push the adapter magazine into the shaft entrance and lock it with the bolt
- ATTENTION! Due to the lower stiffness of the 8 mm cable, it should never be used in large pipes or with hard obstacles.
Adapter attached to the RM 300
Drain cleaning
- Position the machine max. 50 cm in front of the opening of the pipeline you wish to clean. Ensure that the stand is firm.
- WARNING! Take care that the Wöhler RM 300 and the mains cable are not placed in water.
- Pull the cable out of the Wöhler RM 300 until the cable is prestressed into a bend (working bend).
- WARNING! Do not form a large working arc with the cable. The cable can overturn – the risk of injury!
- Insert the cable approx. 50 cm into the pipeline.
- WARNING! Guide the spiral only with the supplied special safety glove.
- Insert the plug.
- Set the control switch to „For
- Press the handle and the cable will start to rotate. NOTE! As long as you press the handle, it is not possible to move the cable forward or backward.
- Release the handle and push the cable further into the pipeline. Repeat this process until you feel resistance. This means you have reached the blockage.
- When the cable has moved into the pipeline so far that the working bend is relieved, pull the cable out of the machine and form a new working bend.
- ATTENTION! If the movement is very stiff, rotate the cable clockwise and anticlockwise so that it does not jam during locking (clockwise rotation) and releasing (anticlockwise rotation). Make sure that the cable does not get wedged, otherwise, it will be damaged
- Pull the cable out of the tube and clean it with water.
- After using the machine, let it freely rotate for 2-3 minutes.
- Flush and dry the cable and augers. Lubricate them with oil and keep them in a dry place to prevent rusting
Maintenance
Regular maintenance
WARNING! Switch off the machine and disconnect the electric power before making any adjustment, accessory assembly and maintenance.
- Keep the machine well lubricated. Inject the lubrication oil ISO VG 32 into oil holes before and after each use
Lubrication the point marked by an arrow
- Keep the electric part of the machine from getting wet. If water accidentally enters the drain cleaning machine with the cable, remove the cover and remove the water
- Prior to the next use, after being stored for a long time, check the machine for free rotation, then turn on the control switch. If the machine shaft does not rotate after the motor is running or the handle is pressed, there may be rust inside. Turn off the electric power immediately to avoid electric damage. In this case, send it to the service or replace the clamp jaws.
Declaration of Conformity
The product:
Wöhler RM 300 Drain Cleaning Machine
has been tested in accordance to essential protection requirements of Council
Directive 2014/30/EU and found the test results indeed meet the limitation of
the relevant test standards listed below:
- EN 55014 :-1 :2017
- EN 61000-3-2 :2014
- EN 61000-3-3 :2013
- EN 55014-2 :2015
Guaranty and Service
Guaranty
Each Wohler RM 200 Drain Cleaning Machine will be tested in all functions and will leave our factory only after extensive quality control testing. The final control will be recorded in detail in a test report and delivered with any unit. If used properly, the warranty period for the Wöhler RM 300 will be 12 month from the date of sale. Consumables such as drain cleaning cables, augers and drain cleaning protection gloves are excluded. This warranty does not cover the freight and packing costs when the device is sent to the factory for repair. Service by non-authorized personnel or making modifications to the device voids any warranty.
Service
Excellent SERVICE is very important to us. Therefore, of course, we are readily available to assist you after the warranty period ends.
- When you send your meter to us, we will re-pair it within a few days and return it via our trusted parcel carrier.
- Immediate help is provided by our technical staff over the telephone.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>